Should the Throttle Be Released When Depressing the Clutch to Shift Gears?

1 Answers
Madeline
07/29/25 11:45am
When shifting gears in a car, the throttle needs to be released. Depress the clutch while releasing the throttle, then change gears, and release the clutch to the semi-engaged position while applying throttle. The clutches commonly used in automobiles mainly include the following three types: Friction Clutch: Refers to a clutch that utilizes the frictional force between the driving and driven parts to transmit torque. It is currently widely used in automobiles. Hydraulic Coupler: Refers to a clutch that uses liquid as the transmission medium. It was previously mostly used in automatic transmissions but is now rarely used in automobiles. Electromagnetic Clutch: Refers to a clutch that utilizes magnetic force for transmission, such as the type used in air conditioning systems.
Was this review help?
20
3
Share
More Forum Discussions

What is the speed in second gear for a manual transmission?

The economical speed for second gear in a manual transmission is 25-40 km/h. Starting in low gear: Generally, first gear is used, with an economical speed of 15-20 km/h. Uphill gear selection: When driving continuously uphill, lower gears (1st or 2nd) should be used. The economical speed for 2nd gear is 25-40 km/h to ensure sufficient vehicle power. Downhill gear selection: When driving continuously downhill, lower gears (2nd or 3rd) should be used. The economical speed for 3rd gear is 40-60 km/h to prevent excessive speed and avoid prolonged brake usage, thus protecting the brake pads.
14
5
Share

What is the difference between two car keys?

Some cars have no difference, while others do. Some cars have a spare key that is just a mechanical key, while others have a spare key that is the same as the main key—a remote key. The specific details are as follows: 1. It is recommended that car owners usually keep the spare key at home, so that if the main key is lost, they can go home to get the spare key to unlock the car door and start the engine. If the spare key is a mechanical key, the car door can be unlocked directly using the lock hole on the door. 2. If the main key is lost, it is important to go to the 4S store immediately to have the technician disable the lost main key, and then get a new key. Remote keys have internal batteries, which will run out after prolonged use. If the battery is dead, the remote function will fail. Therefore, car owners should replace the battery in time when the remote key's power is low to avoid delays in using the car.
2
0
Share

Does one red and one green light indicate charging?

One red and one green light indicates a damaged charger. The user should replace the electric vehicle charger. Below is relevant information: 1. Fault reason: If the red and green lights do not turn on, flash, or both stay on, it indicates an abnormality and the charger can be determined as damaged. If only the green light stays on steadily, it means the charger is receiving power normally internally, and the next step of inspection should proceed. If the green light does not turn on, it indicates an abnormality and the charger can be determined as damaged. If only the green light stays on steadily, it means the charger is receiving power normally internally, and the next step of inspection should proceed. 2. Notes: Over time, the red light on an electric vehicle will gradually brighten from dim. Typically, it takes 4-8 hours to fully charge the battery, at which point the red light reaches its brightest level. Under constant voltage float charging (indicated by the red light), even prolonged charging will not damage the battery.
1
0
Share

What are the reasons for severe jerking in Wanliyang CVT25?

The reasons and solutions for severe jerking in Wanliyang CVT25 are as follows: 1. Insufficient lubrication: Since most mainstream CVT transmissions require oil, insufficient lubrication during cold starts may lead to poor connection between the chains. This can easily cause impact when the clutch engages during cold starts, resulting in jerking when shifting gears. Solution: To avoid this, ensure the vehicle is warmed up and press the brake firmly when shifting to allow the clutch to engage smoothly. 2. Design and quality issues: CVT failures are mainly caused by poor torque converter design (connecting the transmission body and the engine), which can lead to shifting impacts at any speed. Additionally, poor quality and excessive chain wear beyond normal values can cause a large amount of metal shavings to accumulate in the oil pan, leading to vibrations in the CVT transmission, though not severe jerking. Solution: Seek professional repair at a specialized maintenance shop.
19
4
Share

Will There Be Any Impact If the Sunroof Is Not Closed Properly and Gets Rained On?

There will be an impact if the sunroof is not closed properly and gets rained on. Below are some relevant introductions about sunroofs: 1. Functions of a sunroof: It can quickly lower the temperature, eliminate fog, and rapidly exchange fresh air. Opening the sunroof while driving can quickly increase the airflow inside the car, thereby improving ventilation in the cabin. 2. Precautions for using a sunroof: Open the sunroof in traffic jams to prevent exhaust fumes from entering the car. During traffic jams, all vehicles are at a standstill, and car exhaust will inevitably spread in the air. Open the sunroof after exposure to the sun to balance the temperature inside the car. In hot summers, after the car has been exposed to the sun, the interior temperature becomes very high. At this time, the owner should promptly open the sunroof.
3
4
Share

What to Do When a Sunroof Leak Causes the Horn to Malfunction?

This issue occurs when the sunroof leaks, causing the horn wiring to get wet and short-circuit. The first step is to address the sunroof leakage problem, followed by a thorough inspection and repair of the horn wiring to eliminate the fault. Solutions: This situation may arise due to aging of the two-way seal, leading to loose water pipes and leakage. Tightening them with waterproof tape can resolve the issue. Alternatively, the connector in the fuse box may be wet and needs to be dried. Precautions: If the two-way seal is aging, the A-pillar seal must be removed and replaced. The two-way seal is located at the sunroof drainage outlet. During routine maintenance, car owners should pay extra attention to the care of the sunroof and its seals.
1
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.