Should the NIO ES6 opt for air suspension?

1 Answers
EleanorFitz
07/30/25 2:50am
Whether to install air suspension should be judged based on the owner's personal needs. The core advantages of installing air suspension are the adjustment of vehicle height and changes in comfort. More relevant information is as follows: 1. Advantages of installing air suspension: When passing over speed bumps or rough roads at low speeds, the vehicle height can be raised to protect the chassis. On high-speed sections, lowering the chassis can provide the NIO ES6 with higher stability, making the vehicle drive more smoothly and reliably. Lowering the vehicle height when exiting the car is particularly beneficial for vulnerable groups such as the elderly and children, making it easier and quicker to get in and out of the vehicle. 2. Lifespan of air suspension: After purchasing a genuine air suspension, it comes with a lifetime warranty, as specified in NIO's specific terms.
Was this review help?
10
4
Share
More Forum Discussions

What is the reason for the constant flashing of the Prado differential lock light?

The reasons for the constant flashing of the Prado differential lock light: It may be due to a damaged differential lock sensor switch. It could also be that the drive solenoid valve needs cleaning, and if the fault persists after cleaning, it should be replaced. If the center differential light flashing causes an engine fault, it is usually due to a faulty oxygen sensor. A four-wheel drive system fault will not trigger the engine light; replacing an oxygen sensor can perfectly resolve this issue. The function of the differential lock: The differential lock serves the opposite purpose of the differential. Its role is to limit the function of the differential. Engaging the differential lock will lock the differential, hindering its function. This is typically used in extreme road conditions, such as when a wheel cannot rotate or when the vehicle is stuck spinning in place. Introduction to the central differential lock: The central differential lock is a locking mechanism installed on the central differential, used in four-wheel-drive vehicles. Its purpose is to enhance the vehicle's ability to traverse poor road conditions. When one of the vehicle's drive axles spins freely, it can quickly lock the differential, turning the two drive axles into a rigid connection.
17
3
Share

What is the reason for the intermittent operation of the Xiali A+ odometer?

The reasons for the intermittent operation of the Xiali A+ odometer: If it is an electronic odometer, the fuse may be blown; if it is a mechanical odometer, the connecting wire may be loose. Determining whether it is a sensor or instrument malfunction: Lift the left front wheel of the car, do not turn on the ignition switch, manually rotate the left front wheel, and use a dedicated test connector VAG1598/4 and a multimeter to measure the resistance value between electrodes 2 and 3 on the sensor connector. The resistance should oscillate between 0 and n. Determining whether it is an instrument or wiring malfunction: Remove the instrument panel without unplugging the connector. Use a multimeter to measure the three electrodes on the instrument. With the ignition switch turned on, the voltage from fuse No. 26 to the power line of the speedometer should be 12V to ground. Use the multimeter's resistance mode to measure the pulse signal line resistance from the instrument to the sensor connector, which should be zero, and the ground electrode resistance to ground should also be zero.
5
2
Share

What causes the abnormal noise in the Audi A4L dual-clutch transmission?

Audi A4L dual-clutch transmission abnormal noise causes: Abnormal noise when in neutral: When there is abnormal noise in neutral and the sound disappears after pressing the clutch pedal, it is generally due to wear and looseness of the front and rear bearings of the transmission shaft or noise from the constant-mesh gears. If the noise occurs in any gear, and if it is the rear bearing of the second shaft making noise, severely loose or damaged bearings should be repaired or replaced. Abnormal transmission noise during low-speed driving: When the vehicle is driving at low speed, an irregular "clatter, clatter, clatter" noise occurs, which turns into more chaotic gear impact noise when the speed increases, and the noise also occurs when shifting gears. This may be caused by poor gear meshing in the transmission. If the noise is slight and relatively uniform, it can continue to be used after running-in. If it is severe and uneven, the transmission should be disassembled for inspection, and if necessary, readjusted or replaced. Abnormal transmission noise during engine idle operation: During engine idle operation, a rhythmic "clatter, clatter, clatter" noise is heard, which becomes more severe when the throttle is increased, accompanied by a noticeable vibration in the transmission. This is generally caused by tooth surface peeling or gear tooth breakage. If the repair assembly is misaligned or the gear center is offset, this noise can also occur. In such cases, the transmission should be disassembled for inspection, and if necessary, new parts should be replaced.
6
5
Share

What is the reason why the automatic start-stop of the Mercedes-Benz A200L does not respond?

Reasons why the automatic start-stop of the Mercedes-Benz A200L does not respond: Failure to meet safety conditions: The vehicle has not reached the ideal working state. Insufficient battery power or low voltage can cause the automatic start-stop to not work. This is because during engine shutdown, the engine cooling fan and in-car air conditioning require power to operate. Engine coolant temperature being too high or too low can also cause the automatic start-stop to not work. Failure to reach the set state: The vehicle has not reached the state set by the driver. When the in-car air conditioning is turned on in summer, if the engine is turned off, the air conditioning compressor will not work. Once the difference between the in-car temperature and the air conditioning set temperature is too large, the automatic start-stop system will restart the engine.
14
1
Share

What is the size of the Volkswagen T-Roc windshield?

The front windshield of the T-Roc measures approximately 145cm in length, 40cm in width, and 6mm in thickness. The T-Roc is a compact SUV produced by FAW-Volkswagen, known for its stylish design and rich features, making it particularly popular among young drivers. Overview of automotive windshields: Car windshields are typically designed as a single-piece, large-curved surface with specific curvatures on all sides. They are primarily made of laminated tempered glass, capable of withstanding strong impacts. Function of windshields: Windshields provide a survival space for passengers. Upon impact and shattering, the glass breaks into small fragments with blunt edges, minimizing the risk of injury to occupants.
10
1
Share

Does the Audi Q7 have autonomous driving?

2021 Audi Q7 does not come with autonomous driving assistance across all trims. Autonomous Driving System: The system employs advanced communication, computer, network, and control technologies to achieve real-time and continuous control over trains. Utilizing modern communication methods, it directly interfaces with trains, enabling bidirectional data communication between the train and ground. This system features fast transmission speeds and large data capacity, allowing following trains and control centers to promptly obtain the exact position of preceding trains. This enhances operational flexibility, improves control efficiency, and better meets the requirements of train autonomous driving. Main Functions of the Autonomous Driving System: The primary functions include bidirectional information transmission between ground and vehicle, as well as comprehensive and emergency handling of operational organization. The ground-vehicle information transmission channel is a crucial component of the train operation automatic control system. The onboard equipment of the automatic control system relies entirely on operational control commands received from the ground control center to operate. It continuously monitors the train's actual speed and the ground's permitted speed commands. If the train speed exceeds the ground operational speed limit, the onboard equipment will implement braking to ensure the safety of train operation.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.