Should the handbrake be engaged or released while driving?

1 Answers
VonNadia
07/29/25 7:44pm
When driving, the handbrake should be released, and when parking, the handbrake should be engaged. Its function is to keep the vehicle stationary when parked, preventing it from rolling downhill. Precautions for using the handbrake: 1. Avoid pulling it too tightly to prevent system damage; 2. Avoid using the handbrake for long-term parking on slopes; 3. Do not engage the handbrake while driving at high speeds; 4. Release the handbrake before starting the car. Driving with the handbrake engaged can damage the braking system, with the following hazards: 1. Accelerated wear of the brake discs and hardening of the brake pads due to overheating, leading to reduced braking performance; 2. Excessive wear of the handbrake brake pads, causing damage to the drive shaft; 3. Locking of the rear wheels and snapping of the handbrake cable, which may result in skidding or rollover.
Was this review help?
18
3
Share
More Forum Discussions

What is the method to upgrade the navigation system in BYD Yuan?

BYD Yuan navigation upgrade method: The navigation system is stored on an SD card. Simply remove it and find the corresponding navigation system online. It's important to note the port parameters of the original vehicle system for the system being used. Embedded systems can only be updated through dealers or repair shops. The BYD Yuan is a compact SUV with body dimensions of 4360mm in length, 1785mm in width, and 1650mm in height, with a wheelbase of 2535mm. The BYD Yuan is equipped with two types of engines: a 1.5-liter naturally aspirated engine and a 1.5-liter turbocharged engine.
10
2
Share

What is the correct method for parking an automatic transmission vehicle?

Correct method for parking an automatic transmission vehicle: 1. On level ground, after coming to a complete stop by pressing the brake, first engage the parking brake, then shift to neutral (N), slowly release the foot brake, and then quickly shift to park (P) and turn off the engine. 2. The correct operation for parking on a slope is to press the brake until the vehicle comes to a complete stop, engage the parking brake, then shift to neutral (N), and slowly release the foot brake. When releasing, you may feel the vehicle move slightly, about a few centimeters. Once the vehicle is completely stationary, shift to park (P). When parking, it is recommended to follow the standard procedure: shift to neutral first, engage the parking brake, then shift to park (P). Additionally, when waiting at a traffic light, never shift to park (P) to prevent potential rear-end collisions that could damage the transmission.
15
3
Share

Can a C1 driver's license drive a pickup truck?

C1 driver's license can drive a pickup truck, as pickup trucks fall within the permitted vehicle types for a C1 license. The C1 license allows driving small vehicles, including small and mini passenger vehicles, as well as light and mini cargo vehicles; light, small, and mini special-purpose vehicles. Other permitted vehicle types include C2, C3, and C4. The term 'pickup' is a transliteration of the American term for a car-truck, which is a light cargo vehicle with an open cargo box behind the cab, where the side panels of the cargo box are integrated with the cab. It is also a dual-purpose passenger-cargo vehicle that looks like a sedan in the front and has a cargo box at the back. Pickups belong to the category of mini cargo vehicles and are an important part of the automotive market. A driver's license generally refers to a driving permit. The full name of the driving permit is the motor vehicle driving license, also known as a 'driver's license,' which is the certificate required by law for motor vehicle drivers.
19
4
Share

What causes the yellow TC light to illuminate on the Buick GL8?

The yellow TC light on the Buick GL8 indicates that the engine control module has detected a fault in the vehicle's traction control system. The specific causes include the following: 1. Solenoid valve failure: The traction control system operates through the solenoid valve. If the solenoid valve fails, the traction control system will malfunction and require immediate repair. 2. Dirty engine oil: Dirty engine oil can clog the solenoid valve filter, preventing the solenoid valve from functioning properly and thus affecting the traction control system. 3. Oil pressure leakage: Wear on the actuator gears and impeller can cause oil pressure leakage, triggering an alarm, which necessitates immediate factory repair. 4. Dirty throttle: When the throttle opening reaches 20%, the engine computer may misjudge and trigger a traction control system fault alarm. Regular throttle cleaning is required.
12
2
Share

How to Apply Invisible Car Wrap Film?

Steps for applying invisible car wrap film: 1. Clean the car body thoroughly; 2. Lay the invisible car wrap film on the car body and measure and cut it to approximate size; 3. Spray water on both the car body and one side of the film; 4. Position the cut film in place and use a squeegee to remove excess water; 5. After securing the film, trim off the excess, leaving about one centimeter for edge sealing; 6. Use a heat gun to shrink and seal the edges. Invisible car wrap film is a type of automotive film, different from other color-changing films. This film is transparent and unnoticeable, hence the name 'invisible car wrap.' It is a paint surface maintenance and beauty product widely used in the automotive film beauty and maintenance industry. Once applied, it isolates the car's paint from the air, protecting against acid rain, oxidation, scratches, and scrapes.
11
2
Share

Where is the transmission oil filler port of BYD F0?

The transmission oil filler port of BYD F0 is located on the top of the transmission, in the middle position where there is a round screw that can be unscrewed. The following precautions should be noted when adding transmission oil: 1. Choose the appropriate viscosity of transmission oil: If the viscosity is too high, it can cause the friction surfaces to overheat, resulting in unnecessary power loss. Conversely, if the viscosity is too low, centrifugal force may cause the oil to be thrown off the gear surfaces, leading to oil seal leakage and potential poor lubrication on the gear surfaces, which increases wear and may even cause sintering. Therefore, selecting the right viscosity is crucial. 2. Use high-quality branded transmission oil: High-quality transmission oil can effectively protect the gears, reduce wear, make vehicle operation smoother, save fuel, and extend the oil's service life, thereby lowering maintenance and repair costs. 3. Regularly clean the engine and replace the transmission oil: During the circulation process, the effective components of the transmission oil are continuously consumed, and foreign substances such as water, fuel, and dust impurities can mix into the transmission oil, degrading its performance. Therefore, it is necessary to clean the engine and replace the transmission oil periodically.
13
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.