Browse

Antiques Collectibles Apparel Baby Kids Items Books， Movies And Music Electronics Free Stuff Garden Outdoor Health Beauty Home Goods Home Improvement Supplies Musical Instruments Office Supplies Pet Supplies Sporting Goods Ticket Toys Games Transportation Others

Used Cars New Cars Others

Business Crafts Design And Web Events Home Improvement Legal Lessons Personal Pets Photography Repair And Technical Support Wellness Writing， Translation， And Transcription Others

Activities & Groups Artists & Musicians Classes & Lessons Events Friendship & Networking Lost & Found Rideshare Sports Teams Volunteers Travel & Travel Partners Skills & Language Swap Other

Should the front and rear brake pads be replaced together?

2 Answers

HarleyFitz

07/24/25 5:21am

Front and rear brake pads do not need to be replaced together as they have different replacement cycles. Compared to front brake pads, rear brake pads have a longer service life. Under normal driving conditions, front brake pads typically need replacement every 30,000-50,000 kilometers, while rear brake pads can last about 60,000-100,000 kilometers before requiring replacement. Introduction to brake pads: 1. Automotive brake pads, also known as brake linings, refer to the friction materials fixed on the brake drum or brake disc that rotates with the wheel. The friction lining and friction block within them withstand external pressure to generate friction, thereby slowing down the vehicle. 2. Automotive brake pads are generally composed of a steel plate, adhesive heat insulation layer, and friction block.

Was this review help?

2

4

Share

DelNova

08/11/25 1:01am

I'm a seasoned auto mechanic who changes brake pads every day. Let me tell you honestly, there's really no need to replace front and rear pads together. The front brake pads handle most of the braking force and wear out at least twice as fast as the rear ones. For regular family cars, front pads typically need replacement around 40,000 km, while rear pads can last at least 70,000 km. Plus, most modern cars have brake wear sensors - it's perfectly fine to replace them when the warning light comes on. During every maintenance check, I always inspect the thickness for customers. I recommend replacement when front pads go below 3mm, while rear pads can still keep working. Replacing both sets simultaneously is just throwing money away - why replace rear pads that still have 20,000 km left? Of course, if you're the type who loves driving fast and brakes aggressively, then the wear will be faster.

Was this review help?

3

5

Share

Expand All

More Forum Discussions

Do Lavida and Bora belong to FAW or SAIC?

Lavida is a compact sedan launched by SAIC Volkswagen; Bora is a compact sedan launched by FAW Volkswagen. The following are the differences between Lavida and Bora: 1. Difference one: Exterior design: Lavida appears very stable, while Bora's front face design is more aggressive. 2. Difference two: Body dimensions: The new Volkswagen Lavida has a length of 4670 mm, a width of 1806 mm, a height of 1474 mm, and a wheelbase of 2688 mm; the new Volkswagen Bora has a length of 4663 mm, a width of 1815 mm, a height of 1462 mm, and a wheelbase of 2688 mm. 3. Difference three: Side design: The new Volkswagen Lavida has a less prominent waistline design, while the new Volkswagen Bora's waistline extends from the front headlights to the rear taillights, appearing more noticeable, and a silver chrome waistline is also equipped below the doors. 4. Difference four: Rear design: The new Volkswagen Lavida's rear design is more rounded, with two small-sized brake lights below the taillights, while the new Volkswagen Bora's taillight design is more three-dimensional, with a folded rear design that gives it a more sporty feel.

What are the steps for changing the oil in an automatic transmission using a machine?

Here are the steps for changing the oil in an automatic transmission: 1. Connect the exchange machine: Open the hood, place fender pads, lift the vehicle, perform a simple inspection of the vehicle's chassis, locate and confirm the position of the transmission cooling oil pipes, select the appropriate connecting adapters, and connect the two hoses of the exchange machine to the transmission's inlet and return oil pipes respectively. 2. Check the old oil: Start the vehicle, connect the smart exchange machine to the battery, turn on the smart exchange machine, and observe the cleanliness of the old oil from the old oil display tube. If metal particles, sludge, friction plate fragments, or other impurities are found in the old oil, it may indicate internal wear in the transmission, requiring further repairs and making it unsuitable for an oil change at this time. 3. Replace the filter: Turn off the engine, lift the vehicle, open the drain plug, and drain the old oil. Use a measurable container to collect the old oil, remove the oil pan, and pour the oil inside the oil pan into the old oil container. Replace the oil pan gasket and, if possible, also replace the filter. Note that the location of the filter may vary significantly between different vehicles. 4. Circulation cleaning: Add new oil to the exchange machine, activate the "fill new oil" function of the exchange machine, set the filling amount to match the drained old oil quantity, and start the vehicle. Activate the "circulation cleaning" function of the exchange machine. The driver should operate the gearshift mechanism to perform circulation cleaning for each gear, with each gear's cleaning time controlled within 5-10 seconds, and the total circulation time between 5-8 minutes. 5. Equal exchange: After circulation, stop the engine, add new oil to the exchange machine again, and select the "equal oil exchange" function. Upon completion, observe whether the colors of the new and old oil in the exchange machine match. If they match, the operation is complete. If not, continue adding new oil until the colors of the new and old oil match. Check if the oil level is sufficient. For transmissions with a dipstick, check the dipstick's scale position. For those without a dipstick, lift the vehicle and open the inspection bolt. Excess oil will overflow from the inspection bolt hole. If no overflow occurs, add new oil via the smart exchange machine based on the actual situation until oil overflows.

How to Replace Valve Stem Seals by Yourself?

Remove the camshaft and hydraulic lifters, storing them face down. Remove the spark plugs and adjust the piston of the corresponding cylinder to top dead center. Screw the pressure hose into the threaded hole. Install the spring compression tool onto the cylinder head. Connect the pressure hose to the air compressor. Use the threaded mandrel and thrust plate to remove the spring. Gently tap the valve spring retainer to remove the valve lock. Use a tool to pull out the valve stem seal. Place the plastic sleeve onto the valve stem and apply a layer of engine oil to the seal lip. Install the seal onto the tool and slowly push it onto the valve guide.

What is the crv240turbo?

Here is the relevant introduction about the Honda crv240turbo: 1. The dimensions of the Honda CR-V are: length 4585mm, width 1855mm, height 1679mm, wheelbase 2660mm, fuel tank capacity 53L, and curb weight 1642kg. 2. The Honda CR-V features a MacPherson strut front suspension and a multi-link independent rear suspension. 3. The Honda is equipped with a 2.0L naturally aspirated engine, delivering a maximum horsepower of 146PS, maximum power of 107kW, maximum torque of 175Nm, and is paired with an electronic continuously variable transmission.

How to fold down the rear seats of the Yaris L?

Before folding down the rear seats, move the front seats forward to ensure there is enough space for the rear seats to be folded. Close the center armrest in the rear seats to avoid friction, and retract the seatbelt buckle of the middle rear seat. It is best to have the headrest in the lowest position. There is a thin strap on the side of the rear seat—pulling it allows you to adjust the backrest angle forward or backward. Fold down the rear seats.

How to Remove the Dashboard of a Mercedes-Benz GLK300?

Use a lock disassembly tool to turn the lock to the left until it comes apart. If professional disassembly tools are difficult to purchase, you can borrow them from an auto shop. Use a pry bar to remove the small panel on the far right (near the right door). Use a hex ball-head screwdriver to unscrew the internal screws. Raise the steering wheel to its highest position, use a pry bar to open the gaps on both sides of the steering wheel lock, remove the air vents, and be careful to disconnect the warning light wiring. Finally, use a pry bar to slowly pry open the screen.

Trending Ranking

What level of car is the Murano?

How many hours can a car run continuously?

How long does it take to charge a car battery to normal?

What engine does the Geely King Kong have?

What to Do When Car Windows Fog Up on Rainy Days?

Where is the Sail Air Filter Located?

Where is the fuel tank cap switch on the Sagitar?

Is the Lavida's Engine Imported?

At what age can you get a driver's license?

Is the Wuling Hongguang Front-Wheel Drive or Rear-Wheel Drive?

More Forum Discussions

Where is the timing belt of the Corolla located?

Can a Car Purchased Out of Town Be Licensed Locally?

How to Determine if Your Installed ETC is Usable?

What Causes the Fault Light in Volkswagen Lavida?

Help

Cookie

Cookie Settings

© 2025 Servanan International Pte. Ltd.