Should the driver's license be renewed upon expiration or in advance?

1 Answers
KinsleyLee
07/30/25 8:46am
Driver's license annual review should be done in advance. Here are the relevant details: Annual Review: For holders of various large passenger vehicles, medium passenger vehicles, large trucks (A1, A2, B1, B2) licenses or school bus staff, the driver's license annual review has been changed from once every two years to once every year. Regulations: Motor vehicle drivers must undergo regular reviews at the traffic management department of the public security authority in accordance with the provisions of laws and administrative regulations. Drivers holding licenses for large passenger vehicles, tractors, city buses, medium passenger vehicles, or large trucks must undergo a review at the traffic management department of the public security authority within thirty days after the end of each scoring cycle. However, if there are no demerit points recorded during a scoring cycle, the review for that cycle is exempted.
Was this review help?
18
5
Share
More Forum Discussions

How many more years can National IV cars be driven?

Currently, there is no explicit national regulation on the mandatory scrapping time for National IV vehicles in China. As long as they can pass the annual inspection at local motor vehicle inspection stations, they can continue to be driven. Below is relevant information about National IV vehicles: 1. Introduction: According to the Ministry of Environmental Protection's plan, China will enforce the National VI emission standards for light-duty vehicles starting from July 1, 2020. Therefore, the remaining time for older National III and National IV vehicles is uncertain. Notably, Shenzhen issued a notice on March 29, announcing that it would implement the National VI emission standards on July 1, 2018, a full two years ahead of the national schedule. 2. Considerations: With the arrival of National VI standards, the usability of National IV vehicles will not be immediately threatened in the short term. Given the current volatile policy environment, if considering whether National IV vehicles are worth purchasing, it's important to note that while they won't be phased out immediately, the advent of National VI will undoubtedly impact their resale value. Therefore, cautious purchasing is advised.
11
3
Share

Can 195 tires be replaced with 205 tires on a car?

The 195 tires on a car can be replaced with 205 tires. Below is relevant information about car tires: 1. Introduction: If you decide to replace them, it is recommended to change the rims as well. Generally, 195 tires are paired with 15-inch rims, while 205 tires are paired with 16-inch rims. Although 15-inch rims can accommodate up to 205 tires, it is still advisable to use 16-inch rims. The numbers 195 and 205 represent the cross-sectional width of the tires. 195 indicates that the tire width is 195 millimeters, and 205 indicates a tire width of 205 millimeters. 2. Considerations: If the rim width reaches 6J, technically, you can switch to 205 tires. However, according to China's current traffic laws, tires must match the factory certificate; otherwise, it is considered illegal modification. Currently, it is not recommended to change tire specifications. If you insist on changing them, be prepared to face potential insurance claim rejections and keep a set of compliant tires for vehicle inspection purposes.
14
1
Share

Where is the car A-pillar located?

Car A-pillars are located on both sides of the front windshield, connecting the two front doors and the engine compartment. The B-pillar is positioned behind the driver's side and serves as the pillar for securing seat belts, also connecting the front and rear doors. The C-pillar is the pillar at the rear of the car that connects the roof to the rear section. Some SUVs and MPVs may also have a D-pillar, which extends further back from the C-pillar. Functions of the car A-pillar: 1. It works together with the front edge of the engine and the vehicle roof to secure the front windshield. 2. The A-pillar also contributes to the structural rigidity of the car body. Together with the B-pillar and C-pillar, it helps prevent secondary injuries to the driver in the event of a rollover accident and enhances the vehicle's stability to a certain extent.
19
1
Share

What is the difference between full trailer and semi-trailer?

The differences between full trailer and semi-trailer are as follows: 1. Different connection methods with the tractor: A full trailer bears all the load by itself and is connected to the tractor only by a hook. The tractor does not need to bear the trailer load but only provides traction; A semi-trailer, in addition to providing support points and power, the tractor also needs to bear part of the trailer load. 2. Different standing methods: A full trailer can stand upright by its own tires, and the entire load is borne by the trailer itself, connected to the main vehicle only by a hook. The main vehicle does not need to bear the trailer load but only provides power to achieve traction and steering of the full trailer; A semi-trailer must rely on the front legs, and the semi-trailer is developed on the basis of the full trailer. The front half of the semi-trailer is placed on the traction saddle at the rear of the tractor, and the bridge behind the tractor bears part of the weight of the trailer.
17
5
Share

How to reset the oil maintenance light on the Lynk & Co 01?

The method to reset the oil maintenance light on the Lynk & Co 01: 1. Turn on the ignition switch without starting the engine; 2. Press and hold the trip meter reset button on the combination instrument panel, then observe the dashboard for a maintenance prompt; 3. The odometer will then begin to count down. When the display shows 0000.0, release the button. The Lynk & Co 01 has a body length, width, and height of 4549mm, 1860mm, and 1689mm respectively, with a wheelbase of 2734mm. The vehicle is front-engine, front-wheel drive, and its engine has a maximum power of 160kw and a maximum torque of 325nm.
7
2
Share

How to Bleed the Air from the X-Trail Clutch?

Method for bleeding air from the X-Trail clutch: 1. Use a plastic hose with one end attached to the bleeder bolt on the slave cylinder and the other end connected to a transparent container. Slowly pump the clutch pedal repeatedly; 2. One person holds down the clutch pedal while another loosens the bleeder bolt to allow hydraulic fluid to flow into the transparent container. Then tighten the bleeder bolt and repeat the operation multiple times until the discharged hydraulic fluid contains no air; 3. The discharged hydraulic fluid has absorbed air and must be left to stand for more than 30 minutes before reuse. Refill the reservoir to the normal level. The X-Trail has a body length, width, and height of 4675mm, 1820mm, and 1722mm respectively, with a wheelbase of 2706mm. The vehicle's engine delivers a maximum power of 111kW and a maximum torque of 194Nm.
8
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.