Should the Atenza use 92 or 95 octane gasoline?

1 Answers
DiElena
07/29/25 1:15pm
The Atenza should use 92 octane gasoline. 92 octane gasoline has an octane rating of 92 and contains 8% n-heptane, making it suitable for vehicles with relatively low compression ratios. The Atenza is a mid-size sedan equipped with a 2.0L L4 naturally aspirated engine, delivering a maximum horsepower of 158ps and a peak torque of 202nm. The vehicle dimensions are 4870mm in length, 1840mm in width, and 1445mm in height, with a wheelbase of 2830mm. It features a 4-door, 5-seat sedan body style, a 6-speed automatic transmission, a top speed of 212 km/h, front-engine front-wheel drive layout, and a unibody construction.
Was this review help?
5
5
Share
More Forum Discussions

Which Prado model features full-time four-wheel drive?

The new Prado is a full-time four-wheel drive model. Full-time four-wheel drive utilizes a flexibly connected central differential, along with independent differentials on the front and rear axles, to distribute driving force to all four wheels. The differential in full-time four-wheel drive can be either a viscous coupling type or a multi-plate clutch type. The advantages of full-time four-wheel drive include: 1. Improved starting and climbing ability, independent of load conditions. 2. Better acceleration performance in low gears, especially with high-power engines. 3. Reduced sensitivity to crosswinds. 4. Greater traction in all road conditions, particularly on slippery and winter surfaces. 5. Reduced torque steer effect; more even tire wear.
7
3
Share

How to adjust the height of the headlights on the Sylphy?

Here are the methods to adjust the height of the headlights on the Sylphy: 1. The headlight height adjustment knob is located below the left side of the steering wheel. Turn the knob to adjust the headlight height. 2. If you are driving without heavy loads/luggage or on flat roads, select the normal position "0". 3. If the number of passengers or the load/luggage in the car changes, the headlight beam may be higher than the normal position. The introduction to headlight height adjustment is as follows: 1. The headlight height adjustment knob is generally located on the left side of the dashboard, near the light control switch. 2. Normally, the knob has numbers from 0 to 3, with higher numbers indicating a lower height. In most cases, position "0" is sufficient. 3. Position "0" is the initial position, representing a level height suitable for when the front seats are occupied and the trunk is empty. Positions 1-3 are suitable for when the vehicle is fully loaded with passengers and luggage.
1
3
Share

What is the method for jump-starting a car?

Method for jump-starting a car is as follows: 1. First, bring the two cars as close together as possible. Generally, car batteries are located under the front hood, so depending on the actual situation, either park the cars side by side or head to head. 2. Then, locate the batteries of both cars, identify the positive and negative terminals, uncover the terminal covers, and use the red battery cable clamp to attach to the positive terminal and the black clamp to the negative terminal. 3. Once all four terminals are connected, the jump-starting setup is complete. Once the cables are properly connected, you can proceed to the car with the dead battery and start the ignition. 4. Use the vehicle's emergency power supply when starting the ignition.
3
4
Share

What to Do When the Dashboard Backlight of Maxus V80 Doesn't Light Up?

The dashboard is a high-definition flat panel or structural component installed with instruments and related devices. It can be classified by form into screen-type dashboards, frame-type dashboards, passage-type dashboards, and cabinet-type dashboards. There are 4 possible reasons why the dashboard backlight of the Maxus V80 doesn't light up: 1. The dashboard backlight switch is not turned on: The solution is to simply turn on the backlight switch. 2. The dashboard circuit board is burnt out: The dashboard needs to be replaced with a new one to resume functionality. 3. The dashboard illumination light is damaged: Disassemble the dashboard. The illumination lights are usually located at the rear of the dashboard. Replace the non-functioning illumination light. 4. The dashboard power supply fuse is blown: Check the electrical fuse of the dashboard. If faulty, replace it with a new fuse.
19
0
Share

How to Remove the Spare Tire of Changan Oshan X7

Here are the steps to remove the spare tire of Changan Oshan X7: 1. The spare tire of Changan Oshan X7 is located under the chassis. To remove it, simply unscrew the fixing bolts and take down the spare tire. 2. Other tools that assist in installing or removing the spare tire can also be taken down at the same time. Below is a brief introduction to Changan Oshan X7: 1. The Oshan X7 features natural aesthetic design and aerospace-grade painting technology. The front face adopts a large hexagonal grille with wave-pattern horizontal bars extending downward. The Changan Oshan Cloud Eagle logo is suspended above the grille, giving the vehicle a distinctive look. Exterior highlights include full-LED natural light compound headlights, dual-tone straight-cut alloy wheels with a whirlwind design, and a continuous waistline design. 2. The Changan Oshan X7 is a compact SUV developed by Changan Oshan Auto, positioned as an urban premium SUV. The new vehicle is based on Changan's global R&D center's new modular MPA-2 platform, which supports the development of EV, hybrid, and traditional fuel vehicles. The Oshan X7 is equipped with a 1.5TGDI engine, delivering a maximum power of 178 horsepower (131kW) at 5500rpm and a peak torque of 265N·m between 1450-4500rpm. It is paired with a wet 7DCT automatic transmission independently developed by Changan and its UK R&D center.
15
3
Share

When was China III released?

China III was released on July 1, 2007. The China III standard is China's third-stage vehicle emission standard. The national third-stage emission standard is equivalent to the European III emission standard, meaning the content of tailpipe pollutants is equivalent to Euro III levels. The difference is that new vehicles must be equipped with an onboard diagnostic (OBD) system. The characteristic of the OBD system lies in the increase of detection points and detection systems, with oxygen sensors installed at both the inlet and outlet of the three-way catalytic converter. By fully monitoring vehicle emissions in real-time to ensure compliance, it can better guarantee the implementation of the Euro III emission standard.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.