Should the Air Conditioning Be Turned Off Before Turning Off the Car?

What Causes the Jerking Sensation When Pressing the Throttle at Low Speed in a Civic?

Civic experiencing a jerking sensation when pressing the throttle at low speed can be a normal phenomenon in some cases, while in others, it may indicate a vehicle malfunction that requires timely inspection. The specific causes and precautions are as follows: Specific reasons for jerking when pressing the throttle: Normal phenomenon: The jerking sensation when pressing the throttle may occur in manual transmission models when driving in a semi-clutch state, where both accelerating and decelerating can cause jerking—the deeper the throttle is pressed, the more pronounced the jerking. For automatic transmission models, there may be a slight jerking sensation during upshifting, which becomes more noticeable when forcefully downshifting and then upshifting with a heavy throttle. Another normal phenomenon: Jerking when pressing the throttle can also be due to excessive carbon buildup in the throttle body, fuel injectors, and intake manifold. Carbon buildup can lead to various malfunctions, and in some vehicles, it may cause jerking. Regular carbon cleaning is recommended. Other causes include substandard fuel quality leading to incomplete combustion, or faults in spark plugs and ignition coils causing cylinder misfires. These issues require inspection and repair at a service center to avoid further safety hazards. Precautions for jerking when pressing the throttle: Engine power is transmitted through the transmission, which is also a key factor affecting fuel consumption. Generally, automatic transmissions consume 10% more fuel than manual transmissions. Whether manual or automatic, more gears usually mean better fuel efficiency. When towing an automatic transmission vehicle due to a malfunction, it is best to lift the drive wheels before towing. Additionally, the towing speed should not be too fast—preferably no more than 35 km/h—and the towing distance should not be too long, ideally within 65 km.

6

2

Share

How to Shift Gears in the Subject 3 Road Test?

Here are the techniques for shifting gears in the Subject 3 road test: 1. When starting the vehicle, use first gear: Always depress the clutch fully when shifting gears; otherwise, you may encounter difficulty engaging the gear. 2. Shift gears progressively: Accelerate to upshift and decelerate to downshift. Ensure that the speed matches the gear, and shift gears one step at a time without skipping. When decelerating, reduce the speed first before shifting. If you accidentally shift into the wrong gear, fully depress the clutch and shift again. 3. Shift quickly but smoothly: When adjusting gears, shift promptly once the speed drops. Speed is crucial, especially during the 100-meter acceleration and deceleration test, which evaluates the driver's shifting speed.

13

4

Share

What does the 4x4 of the Mercedes-Benz G-Class mean?

Mercedes-Benz G-Class 4x4 represents a four-wheel drive system with four wheels. Here are some details about the Mercedes-Benz G-Class 4x4: 1. Introduction to the Mercedes-Benz G-Class 4x4: Four wheels, a four-wheel drive system, and two shock absorbers per wheel, totaling eight shock absorbers. 3. Overview of the Mercedes-Benz G-Class: The Mercedes-Benz G-Class is a representative of hardcore off-road vehicles and has almost no rivals in this field. Its three differential locks—central differential lock, rear differential lock, and front differential lock—are well-known and ensure powerful off-road capabilities. The G-Class has maintained its iconic boxy design, which is quite retro but highly recognizable. Just by looking at the model, one can immediately identify it as the Mercedes-Benz G-Class, which is part of its success.

12

0

Share

How to Remove the Car Windshield Washer Nozzle?

To remove and install the car washer nozzle, locate the nozzle position and simply use a screwdriver to pry it up. Below are precautions for using the car washer nozzle: 1. Check the nozzle's spray position: If the spray position is incorrect, adjust it promptly. The normal spray position should direct the cleaning fluid to the upper-middle part of the windshield. As the fluid flows down, the wiper blades will evenly spread it across the entire windshield, cleaning and removing dirt. Generally, the nozzle position can be adjusted manually. Some models have screws fixing the nozzle, which can be loosened before adjustment. 2. Regularly check and replenish the windshield washer fluid: If the fluid runs out and the driver continues to use the spray switch, the pump will run dry, causing the motor to overheat and burn out due to lack of fluid flow.

3

Share

Can the Vehicle License Show the National Emission Standard?

Methods to check the national emission standard on the vehicle license: Directly check the vehicle model number on the license. 'Y' indicates the National IV emission standard, and 'V' indicates the National V emission standard. However, after testing by most people, it has been confirmed that this method is not applicable to all vehicle models. Other methods to check the emission standard: 1. Vehicle's environmental protection label: The simplest and most direct method is to look at the vehicle's environmental protection label, which has clear markings on the back. 2. Factory certificate: For new vehicles, you can check the vehicle's factory certificate or vehicle conformity certificate. 3. Query platform: You can also log in to the public query platform of the Motor Vehicle Environmental Protection Network, enter the vehicle's VIN number (Vehicle Identification Number) and the last 6 digits of the engine number to query vehicle information.

14

4

Share

What Causes the Abnormal Noise When Releasing the Brake at Car Start?

Abnormal noise when releasing the brake at car start is due to damage in the brake system. The specific reasons are as follows: 1. Brake Pads: Abnormal clearance in the brake pads. 2. Brake Disc: Uneven hardness of the brake disc, affecting the uneven surface of the brake pads. 3. Braking: Release the brake once before the vehicle comes to a complete stop, then lightly apply the brake until the vehicle stops moving. 4. Engine Braking: When braking while the vehicle is in a curve, reduce the speed sufficiently through braking. However, if it's too late to slow down, the brake can be used briefly according to the situation. Emergency braking on slippery curved roads can easily cause the tail to swing out, which can be mitigated by downshifting the gearbox and utilizing engine braking to slow down.

18

4

Share

Should the Air Conditioning Be Turned Off Before Turning Off the Car?

What Causes the Jerking Sensation When Pressing the Throttle at Low Speed in a Civic?

How to Shift Gears in the Subject 3 Road Test?

What does the 4x4 of the Mercedes-Benz G-Class mean?

How to Remove the Car Windshield Washer Nozzle?

Can the Vehicle License Show the National Emission Standard?

What Causes the Abnormal Noise When Releasing the Brake at Car Start?

What brand is KLC engine oil?

What are the driving license medical examination items?

How Does Water Damage Insurance Work?

What car is the K logo?