Should I Use Recirculation Mode When Turning on AC in Summer?

How to Set Up Auto-Lock for the Ford Kuga?

To enable the auto-lock feature on the Ford Kuga, it is necessary to modify the vehicle's onboard computer data through reprogramming. However, the auto-lock function on the Ford Kuga allows doors to be opened from inside at any time, and there is also a manual lock feature on the driver's side door panel. Below are relevant details: 1. The auto-lock function is designed for anti-theft purposes. It automatically locks the doors shortly after the vehicle starts moving, helping prevent carjacking during traffic jams or at red lights, thereby enhancing security. 2. It also provides protection when child passengers are in the car, preventing them from opening the door handles during travel and falling out, which could lead to personal injury. 3. Drivers should not overly rely on the auto-lock feature. Instead, they should proactively enhance safety awareness by manually locking doors immediately after all passengers enter the vehicle. Cultivating good driving habits ensures the safety of all occupants during travel.

2

1

Share

What Causes the Car Battery Warning Light to Illuminate?

Reasons for the car battery warning light to illuminate: 1. The alternator has malfunctioned and cannot charge the battery properly; 2. The alternator belt is broken, loose, or slipping, preventing it from charging the battery; 3. The battery's positive and negative terminals are loose or severely oxidized, causing poor contact; 4. The battery is excessively worn or discharged, leading to an inability to store power properly. If the battery has been in use for too long, it should be replaced promptly. If the driver notices the battery warning light illuminated while driving, it is advisable to pull over immediately. The illumination of the battery light indicates a fault in the vehicle's charging system. Continuing to drive under such conditions may lead to the battery draining completely, causing the car to stall and potentially creating safety hazards.

6

4

Share

How Long Should You Keep the Engine Running After a Jump Start?

Generally, when a car needs to be jump-started due to a dead battery, the engine should be kept running for about half an hour before turning it off. The exact duration may vary depending on the remaining charge of the battery. Here's the detailed procedure for jump-starting a car: 1. Take one jumper cable and connect one end to the positive terminal of the donor car's battery, then connect the other end to the positive terminal of the dead battery. 2. Take another jumper cable and connect one end to the negative terminal of the donor car's battery, then connect the other end to an unpainted metal surface on the engine block of the car with the dead battery. 3. Start the donor car, then start the disabled car following normal starting procedures. 4. After successfully starting the disabled car, let it idle for about half an hour to recharge the battery. Always connect the positive terminals first and then the negative terminals when jump-starting; when disconnecting, remove the negative cables first followed by the positive ones. Important notes about car batteries: 1. Disconnect the battery if the car won't be used for an extended period to prevent power drain and battery discharge. 2. Regularly check and maintain the battery's charge level. 3. Avoid using electronic devices in the car when the engine is off. 4. Do not perform any battery operations in high-temperature conditions. 5. When replacing the battery, it's best to use an original equipment manufacturer (OEM) battery.

1

Share

What does the faucet light displayed on the car mean?

The faucet light displayed on the car is the engine status indicator light. This indicator light is used to display the working condition of the vehicle's engine. When starting the vehicle, the light will illuminate during the self-check and then automatically turn off. If the light remains on, it indicates issues such as poor engine combustion, engine knocking, poor fuel quality, or internal engine cylinder contamination. The engine fault light is controlled by the engine computer, which essentially manages all electrical components of the engine. Therefore, any faults will be displayed through the engine fault light. There are many reasons why the engine fault light may illuminate, including issues with the purge solenoid valve controlling fuel vapor emissions, air flow meter failure, ignition coil failure, thermostat failure, catalytic converter failure, oxygen sensor failure, excessive carbon buildup in the electronic throttle, etc.

4

3

Share

Can You Drive Without Brake Pads?

Driving without brake pads should be avoided, and new brake pads should be replaced immediately. Here is relevant information: If the brake pads are completely worn out, continuing to drive is extremely dangerous. After the brake pads are worn out, each time you press the brake pedal, it may also cause damage to the brake discs. Car braking system precautions: 1. During routine maintenance, always check the thickness of the brake pads and brake discs. If the brake pads are too thin, they should be replaced promptly. Generally, the front brake pads wear faster than the rear ones. 2. Brake fluid should also be checked regularly. Brake fluid is a liquid that easily absorbs moisture. If the water content in the brake fluid reaches 3%, it should be replaced immediately. Measure the water content of the brake fluid during each maintenance. If you live in a humid area, the brake fluid is more prone to absorbing moisture and deteriorating. 3. When replacing brake fluid, it is best to go to a 4S shop. Some small repair shops may not fully remove air from the brake system lines after replacing the brake fluid, which can reduce braking force, increase stopping distance, and affect driving safety. 4. When purchasing brake pads, it is also best to buy them from a 4S shop. Some repair shops may sell counterfeit or substandard brake pads. If you feel that the original brake pads do not provide enough braking force, you can purchase higher-quality brake pads to significantly improve braking performance.

14

0

Share

What is the tire pressure for 32psi?

32psi is equivalent to 2.2bar. Psi refers to the unit of tire pressure, while bar is the unit of pressure measurement. The standard tire pressure for car tires is typically represented in bar. The manufacturer-recommended tire pressure standard for vehicles ranges from 2.3 to 2.5bar. As long as the tire pressure remains within this reasonable range, both the comfort and handling performance of the vehicle can be well ensured. Strictly speaking, tire pressure refers to the air pressure inside the tires. In automotive maintenance, the engine is considered the heart of the car—its failure would signify the end of the vehicle's lifespan. Similarly, tire pressure acts as the blood pressure of the car, where its level plays a crucial role in the vehicle's performance and power.

2

1

Share

Should I Use Recirculation Mode When Turning on AC in Summer?

How to Set Up Auto-Lock for the Ford Kuga?

What Causes the Car Battery Warning Light to Illuminate?

How Long Should You Keep the Engine Running After a Jump Start?

What does the faucet light displayed on the car mean?

Can You Drive Without Brake Pads?

What is the tire pressure for 32psi?

Has the New Santana Been Discontinued?

Does the Subaru BRZ comply with China 6 emission standards?

Is the Haima M6 fuel filter internal or external?

Does Cruise Control Save Fuel?