Should I Inflate the Tires When the Pressure Drops Due to Cooling?

How to distinguish the inner and outer sides of Giti tires?

There are three methods to distinguish the inner and outer sides of Giti tires. Below is a detailed explanation of these three methods: 1. Symmetrical tread tires: There is no distinction between front, back, left, right, inside, or outside during installation. The side with the production date should be placed on the outside. 2. Asymmetrical tread tires: During installation, the side marked with the word "outside" should be placed on the exterior. 3. Unidirectional tread tires: There is no distinction between inner and outer sides during installation, but the side with the production date should be placed on the outside. However, the tire must be installed in the direction indicated by the arrow, which represents the rolling direction of the wheel. Installing unidirectional tires incorrectly can reduce grip, create uneven resistance on both sides, diminish braking effectiveness, cause the vehicle to pull to one side, result in unstable steering, and hinder water drainage during rainy conditions, leading to potential safety hazards. If tires are installed incorrectly, the vehicle's comfort will be affected, and wear will accelerate more quickly than under normal conditions.

1

0

Share

Can You Release the Clutch in First Gear?

You can fully release the clutch when driving in first gear. However, the clutch should be released slowly in first gear. Once the car starts moving, you can release it completely. Since first gear provides a relatively high output torque, releasing the clutch gradually helps prevent the car from jerking forward or stalling. Steps for starting a car: Fasten the seatbelt and adjust the seat; quickly press the clutch pedal to the floor and shift into first gear; turn on the indicator, check the surroundings, and release the handbrake; quickly lift the clutch to the semi-engaged position, pause slightly, then slowly release the clutch while gently pressing the accelerator to ensure a smooth start. Correct clutch operation when shifting gears: Avoid keeping the clutch in a semi-engaged state for extended periods. Some drivers have the bad habit of unconsciously resting their foot on the clutch pedal, keeping it semi-engaged while driving. The left foot should be moved away when the clutch is not in use, as prolonged semi-engagement accelerates clutch wear. Fully depress the clutch before shifting. If the clutch pedal is not fully pressed down when shifting, it can cause a "gear grinding" phenomenon, which can severely damage the transmission over time. Only press the clutch pedal when braking at speeds below 20km/h. Pressing the clutch at higher speeds does not aid braking effectiveness. However, during emergency braking, both the brake and clutch should be pressed simultaneously.

9

2

Share

Are Out-of-Town New Energy Vehicle License Plates Subject to Traffic Restrictions?

Out-of-town new energy vehicle license plates are subject to traffic restrictions. Below is an introduction to the process of purchasing license plates for new energy vehicles: Obtaining Temporary License Plates: After selecting the vehicle at the 4S dealership and paying the final installment, you can purchase insurance at the insurance counter within the 4S store. Then, with all the necessary documents in hand, proceed to the nearest traffic management bureau to obtain temporary license plates. For the first-time application, choosing a bureau close to the 4S store is sufficient. Business Verification: Business verification, also known as business filing, is the process where the local Administration for Industry and Commerce records and files the newly sold vehicle for future reference. If the purchased new vehicle hasn't undergone business verification before the inspection and license plate registration, it won't affect the subsequent inspection and registration process. After obtaining the temporary license plates, return to the 4S store to drive the vehicle for business verification. Tax exemption certificate for vehicle purchase tax, online license plate self-selection: To self-select license plates online, you need to register and choose a number on the Public Security Traffic Safety Comprehensive Service Management Platform.

13

3

Share

What are the reasons for a truck lacking power when going uphill and not responding to acceleration?

The reasons for a truck lacking power when going uphill and not responding to acceleration: 1. Excessively rich air-fuel mixture. 2. Excessive engine oil in the fuel. 3. Poor sealing of piston rings or crankshaft oil seals. 4. Presence of water in the fuel. 5. Faulty spark plugs. 6. Overly dirty air filter. Additional information on troubleshooting and diagnosis is as follows: 1. Improper mixing of fuel and oil: If the mixed fuel contains too much oil or the oil quality is poor, the oil in the combustible mixture cannot be completely burned, resulting in black smoke. For two-stroke engines with separate lubrication systems, an improperly adjusted oil pump supplying too much oil can also cause the above phenomenon. 2. Excessive wear or breakage in four-stroke engines: This can cause oil to enter the combustion chamber, leading to excessive oil in the mixture. If the crankshaft oil seal in a two-stroke engine is damaged, it can also allow oil from the transmission to enter the crankcase and subsequently the combustion chamber with the mixture.

16

0

Share

How long can the annual inspection of a truck be delayed?

Truck annual inspection cannot be delayed for more than 30 days. Vehicles must undergo annual inspection once every year. For vehicles over 10 years old, inspection is required every 6 months. Small and micro non-operational passenger vehicles require inspection once every 2 years within the first 6 years, once every year after exceeding 6 years, and once every 6 months after exceeding 15 years. If a motor vehicle fails to obtain the inspection compliance mark for 3 consecutive inspection cycles after the expiration of the valid inspection period, it will be mandatorily scrapped. Additional required documents for vehicle annual inspection include: 1. Required documents: Original "Motor Vehicle License Plate Application Form". Motor vehicle compulsory traffic accident liability insurance certificate. 2. Copy of vehicle and vessel tax payment or tax exemption certificate. If tax payment information is noted on the compulsory traffic accident liability insurance certificate, provide the original insurance certificate. 3. Original motor vehicle safety technical inspection compliance certificate. Original "Motor Vehicle Driving License". For entrusted issuance of motor vehicle inspection compliance marks, also provide the original "Notice of Entrusted Issuance of Inspection Compliance Mark". 4. For proxy registration, provide the agent's identity proof and the original legally binding written power of attorney issued by the vehicle owner.

15

2

Share

Can Engine Oil Replace Hydraulic Oil?

Engine oil cannot replace hydraulic oil, as doing so may damage your vehicle. Each type of oil is specifically formulated for its intended environment and purpose. The concept of mixing or using oil beyond its designated scope is quite broad. Generally, any lubricating oil can be referred to as engine oil, which is short for mechanical oil. Its composition consists of base oil with some antioxidants, and its viscosity can be selected. More details about hydraulic oil are as follows: 1. Function of Hydraulic Oil: Hydraulic oil is a hydraulic medium used in hydraulic systems that utilize liquid pressure energy. It plays roles in energy transmission, system lubrication, corrosion prevention, rust prevention, and cooling within the hydraulic system. The properties of engine oil and hydraulic oil differ. Most importantly, the quality of hydraulic oil significantly impacts the operational reliability and lifespan of the hydraulic system. Using engine oil as a substitute can easily damage the hydraulic system, so it is advised not to attempt replacing hydraulic oil with engine oil. 2. Differences Between Hydraulic Oil and Engine Oil: Hydraulic oil is primarily used in hydraulic systems and is a type of industrial lubricant. In industrial applications, standard hydraulic oil (there are also synthetic variants) is formulated by blending base oil with various additives such as antioxidants, anti-wear agents, and anti-foaming agents. Mineral engine oil is derived from refined petroleum, while fully synthetic engine oil is made from artificially synthesized base oil. Engine oil is often referred to as the lifeblood of an engine, serving functions such as lubrication, cleaning, sealing, heat dissipation, buffering, and rust prevention within the engine.

17

1

Share

Should I Inflate the Tires When the Pressure Drops Due to Cooling?

How to distinguish the inner and outer sides of Giti tires?

Can You Release the Clutch in First Gear?

Are Out-of-Town New Energy Vehicle License Plates Subject to Traffic Restrictions?

What are the reasons for a truck lacking power when going uphill and not responding to acceleration?

How long can the annual inspection of a truck be delayed?

Can Engine Oil Replace Hydraulic Oil?

How to Remove the Daytime Running Lights on a Volvo XC60?

How early can a vehicle with semi-annual inspection be inspected in advance?

Where is the Touareg Water Temperature Sensor 2 Located?

How Long After Sheet Metal Painting Can You Wash the Car?