Should Cars Be Waxed?

1 Answers
Alejandro
07/25/25 4:32pm
Yes, cars should be waxed. Here are some key points about car waxing: 1. Benefits: Proper waxing significantly enhances the protection level of the car's paint surface. It not only makes the paint less susceptible to damage and slows down the aging process, but also helps to some extent in preventing the paint from getting dirty. 2. Precautions: Incorrect waxing frequency or methods can cause some irreversible damage to the car's paint. Generally, new cars come with a layer of protective wax on their paint when they leave the factory. Waxing too early may remove this original protective wax from the new car's surface.
Was this review help?
10
2
Share
More Forum Discussions

What are the symptoms of a faulty steering column in a car?

When the steering column in a car is faulty, the following symptoms may occur: 1. Difficulty in controlling the vehicle: The steering may easily deviate or drift, making it hard to steer the vehicle. The owner should immediately take the car to a repair shop for inspection and, if necessary, replacement. 2. The steering shaft is the transmission component connecting the steering wheel and the steering gear: The steering column is fixed to the car body, and the steering shaft passes through the steering column, supported by bearings and bushings inside the column. In the event of a collision, the steering column and steering shaft at the front of the car will move backward, while the driver, affected by inertia, will be propelled toward the steering wheel. Part of the energy is absorbed by the restraint system, and another part is transmitted to the steering wheel and steering column. A good automotive steering system should minimize the driver's injuries in the event of a collision.
9
5
Share

Puncture Repair or Replacement?

Whether to repair or replace a punctured tire depends on the specific situation. The relevant guidelines are as follows: 1. In general, if the tire is punctured by a nail or wire: and there is no extensive damage to the internal structure of the tire, with the steel wires and fabric layers in the tire ply remaining intact, and only a small hole is present, then repairing the tire is sufficient. Typically, such small holes can be fixed using an internal patch repair method. For slightly larger holes, a mushroom plug repair can be used. However, if the puncture diameter reaches or exceeds 6mm, it is advisable to replace the tire with a new one. 2. If the tire is scratched during skidding: resulting in a long wound, the depth of the wound should be assessed. Generally, if the depth does not exceed the tread groove depth, the tire can be used temporarily. However, sometimes the depth of the wound may not be visible to the naked eye. In such cases, it is best to have it inspected at a professional shop. If the internal structure of the tire is damaged, it is recommended to replace the tire with a new one.
14
4
Share

How to Read a Pressure Gauge When Inflating Tires?

Correct usage of a tire pressure gauge is as follows: 1. The angle between the center line of the pressure gauge's measurement port and the axis of the gauge body should be 90°-180°: The scale is a quadrangular prism with a range of 0.07Wpa-0.4Wpa. Before reading, gently tap the instrument's casing or glass surface with your finger to eliminate friction in the transmission mechanism. 2. When observing, the pointer should overlap with the mirror pointer: The value indicated by the pointer at this time is the pressure reading, accurate to one decimal place. Read the temperature value on the pressure gauge, precise to one decimal place. 3. Align and press the measurement end notch of the pressure gauge with the tire valve: At this point, the pointer of the tire pressure gauge will deflect, and the indicated value is the inflation pressure of the tire. If the gauge's indicator rod is pushed out by the pressure, the value displayed on the rod is the tire's inflation pressure. The greater the internal pressure, the more the pointer will deflect.
6
3
Share

How to Determine if an Automotive Air Conditioning Compressor is Good or Bad?

Here are the methods to determine if an automotive air conditioning compressor is good or bad: 1. The quality of the compressor, or its working efficiency, can be judged under normal conditions by connecting a three-way pressure gauge set. After starting the engine, if the low-pressure gauge needle drops rapidly and the high-pressure gauge needle rises quickly, and when the throttle is increased, the amplitude of these changes becomes even greater, it indicates good performance. Conversely, if the amplitude of these changes is not significant during the above operations, it suggests low efficiency and poor performance. 2. If the gauge needles show no noticeable changes at all, it indicates no efficiency, meaning the compressor may no longer be functioning properly.
14
3
Share

What is the difference between D gear and S gear?

D gear stands for "Drive", representing the forward gear; S gear stands for "Sports", representing the sports gear. The relevant introduction is as follows: 1. D gear is the forward gear: When the car is in D gear, the driver does not need to control the gear anymore, just operate the throttle and brake directly. D gear is usually used for daily driving, but when it is necessary to drive on mountain roads or climb slopes, the low gear should be engaged. 2. S gear is the sports mode: When the car is in this gear mode, the transmission can shift gears freely, but the shifting will have a certain delay, which allows the engine to maintain high-speed operation for a long time, thereby obtaining more power and having faster acceleration ability. S gear is usually used for climbing slopes and quick overtaking.
13
3
Share

What is the correct way to use car lights?

The correct methods for using car lights are as follows: 1. High beam: Also known as headlights, high beams are typically used in rural areas or when road lighting is poor. High beams are very bright and can be glaring to pedestrians and oncoming vehicles. Misuse of high beams can be dangerous, so it's essential to use them correctly. 2. Low beam: Low beams are mainly used in situations such as driving closely behind another vehicle at night, entering tunnels, or during nighttime encounters with other vehicles. When driving on well-lit roads at night, low beams should be used. 3. Fog lights: Fog lights are usually installed at the front and rear of the car and are used to illuminate the road and provide safety warnings during rainy or foggy conditions. They enhance visibility for the driver and other traffic participants.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.