Should Cars Be Equipped with Mudguards?

1 Answers
VanJason
07/29/25 9:21am
Yes, cars should be equipped with mudguards. Here is an introduction to mudguards: 1. Functions of mudguards: (1) To prevent mud from splashing onto the car body or people, avoiding an unsightly appearance. (2) They also prevent mud from splashing onto tie rods and ball joints, which could cause premature rust. (3) Small stones can easily get stuck in tire treads, and at high speeds, they may be flung onto the car body, chipping the paint. Installing mudguards can effectively protect the car's paint. 2. Benefits of mudguards: Mudguards can effectively protect the car body from scratches. They serve a protective function for the car body, and installing them helps safeguard the vehicle. During rainy weather, they reduce mud splashing and minimize damage from road gravel being flung by the tires.
Was this review help?
16
1
Share
More Forum Discussions

What are the precautions for inspecting a used car?

Precautions for inspecting a used car include: 1. Exterior body: When examining the vehicle's exterior, carefully observe the paint surface. The method is to stand at a 45-degree angle in front of the car and check if the body lines are straight, looking for any dents, scratches, or marks. Also, check if the left and right sides of the body are symmetrical and if the windshield is intact. 2. Interior: The car's interior is a crucial factor reflecting the comfort of the vehicle. When purchasing a used car, especially a sedan, pay special attention to details such as the interior layout, design, and decorations to ensure that the vehicle is easy and flexible to operate, has a reasonable and compact interior arrangement, pleasing interior aesthetics, and an overall comfortable feel.
11
2
Share

How to Adjust the Left and Right Rearview Mirrors for Subject Two?

Subject Two examination vehicle left and right rearview mirror adjustment methods are as follows: 1. After getting into the car, adjust the seat and backrest properly, maintain a normal driving posture, and start adjusting the rearview mirrors. 2. The rearview mirror adjustment buttons are located on the inner side of the front door and can be adjusted in four directions: up, down, forward, and backward. 3. Left rearview mirror adjustment method: Maintain an upright sitting posture and adjust the left rearview mirror. For left-right adjustment, the car body should occupy one-third of the left rearview mirror surface; for up-down adjustment, the rear door handle should appear near the upper edge of the left rearview mirror surface, allowing visibility of the left rear wheel. 4. Right rearview mirror adjustment method: Maintain an upright sitting posture. For left-right adjustment, the car body should occupy one-third of the right rearview mirror surface; for up-down adjustment, the rear door handle should appear near the upper edge of the right rearview mirror surface.
2
4
Share

Is It Normal for the Buick Center Console Screen Not to Light Up?

It is not normal for the Buick center console screen not to light up. Reasons for the screen malfunction include power supply issues, poor connection of the wiring harness, or host unit failure. Below are the detailed explanations: Power Supply Issues: Failure of the power supply module can prevent the display screen from receiving power normally, resulting in no display. It is recommended to inspect and replace the power supply module if necessary. Poor Connection of the Wiring Harness: Short circuits, open circuits, or poor connections in the wiring harness can cause the screen not to light up. It is advised to check for oxidation or poor contact at the connectors. Host Unit Failure: The display screen itself may have hardware failures or may have reached the end of its service life. Testing with a new display screen can help determine if normal function can be restored.
14
0
Share

Is the Clanking Sound When Driving a Sagitar on Bumpy Roads a Problem?

Sagitar making clanking sounds when driving on bumpy roads is indeed a problem. Lower control arm causing abnormal noises when the car is bumpy: Lower control arm: The function of the lower control arm is to support the tire. There are rubber pads at two positions on the lower control arm, and another position is where a small ball joint is installed, mounted on the steering knuckle. Long-term driving and steering wheel rotation can cause wear on the small ball joint and rubber pads, resulting in excessive gaps and abnormal noises when driving on uneven roads. Stabilizer bar ball joint causing abnormal noises when the car is bumpy: The function of the stabilizer bar ball joint is to maintain the stability of the car during driving. For example, when the horizontal heights of the left and right wheels are different, to prevent torsion of the bar body, the stabilizer bar generates anti-roll resistance to inhibit body roll. Long-term driving and turning can cause excessive wear inside the small ball joint, leading to excessive gaps and abnormal noises. The solution is to replace the new parts, which can directly resolve the noise issue.
18
2
Share

What to Do When the Honda Fit Key Cannot Be Pulled Out?

After turning off the key, apply a little force towards the lock cylinder and press it downward, then you can pull it out. As the main security latch of the vehicle, the use and maintenance of the car key directly affect the smoothness of travel and the protection of valuable property. There are two common faults with car keys: one is the inability to turn the key after insertion, and the other is the inability to remove the key after turning off the engine. There are two common causes for this: 1. Incorrect parking gear position: Because the automatic transmission did not fully return to the P position, but did not trigger the electronic sensor, or there are coins or other objects in the gear slot obstructing the return. Solution: Check if there are any obstructions in the gear slot. If there are, remove them. Then start the car again, shift the gear to confirm it is fully returned, and the key can be pulled out. 2. Steering wheel lock: The reason the key cannot be turned after insertion may be that the steering wheel was not returned to the correct position during the last parking, causing an abnormal lock of the steering wheel. Solution: While gently turning the key with your right hand, wiggle the steering wheel left and right with your left hand, and the key can then be turned.
7
4
Share

What to Do If a Beginner Driver Keeps Stalling the Car?

The main reason for stalling is that beginners are not yet proficient in controlling the clutch, leading to uncoordinated operation between the clutch and throttle. Here are some methods to avoid stalling: Mastering the Clutch: When starting the car, proper clutch control is key to avoiding stalling. Beginners often struggle with clutch control, especially in manual transmission cars. Releasing the clutch too slowly can cause the car to stall. Therefore, when starting, press the clutch pedal with your left foot, hold it steady when halfway released, and then gradually release it as the car begins to move. Applying the Throttle: While controlling the clutch, applying the throttle is equally important. Simply releasing the clutch without applying throttle can cause the car to move too slowly and stall. Therefore, gently press the throttle while releasing the clutch to ensure a smoother start. Using the Handbrake: Beginners may sometimes experience the car rolling backward when starting, which can cause panic and lead to stalling. In such cases, using the handbrake can help. Before shifting into gear to start, engage the handbrake, release the clutch halfway, then disengage the handbrake while applying the throttle. This method prevents the car from rolling backward. Avoiding High Gear at Low Speed: During normal driving, operating the car in a high gear at low speed can cause the engine to shake and lose power, leading to stalling. Therefore, beginners should learn the right timing for gear shifting.
8
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.