Browse

Antiques Collectibles Apparel Baby Kids Items Books， Movies And Music Electronics Free Stuff Garden Outdoor Health Beauty Home Goods Home Improvement Supplies Musical Instruments Office Supplies Pet Supplies Sporting Goods Ticket Toys Games Transportation Others

Used Cars New Cars Others

Business Crafts Design And Web Events Home Improvement Legal Lessons Personal Pets Photography Repair And Technical Support Wellness Writing， Translation， And Transcription Others

Activities & Groups Artists & Musicians Classes & Lessons Events Friendship & Networking Lost & Found Rideshare Sports Teams Volunteers Travel & Travel Partners Skills & Language Swap Other

Should Brake Pads Be Replaced at a 4S Shop?

1 Answers

LaCameron

07/29/25 1:22pm

Brake pads do not need to be replaced at a 4S shop; they can also be replaced at a nearby repair shop. The specific replacement steps are as follows: 1. Check the brake fluid level: Open the engine compartment to check the brake fluid level to prevent overflow during the replacement process. 2. Remove the wheel: Take off the wheel where the brake is located. 3. Remove the brake pads: Unscrew the bolts of the brake caliper and take out the brake pads. 4. Install the new brake pads: Install the new brake pads, tighten the guide bolts, and the replacement is complete. The maintenance methods for brakes are as follows: 1. High-temperature protection: Prevent corrosion of the brake system. 2. Cleaning method: Clean oil stains from the brake discs, brake drums, and brake pads to ensure good heat dissipation of the brake discs. 3. Oil change: Regularly replace the brake fluid. 4. Inspection: Regularly check the thickness of the brake pads or brake shoes.

Was this review help?

1

4

Share

More Forum Discussions

How to Deal with Paint Peeling on a White Car?

Methods for handling paint peeling on a white car: 1. Minor scratches: If the scratches are not very noticeable, simply apply wax; 2. Visible scratches without damaging the base coat: First clean the paint surface, wipe back and forth with a soft towel dipped in toothpaste, then wipe off with a clean towel; 3. Scratches that reach the base coat: After cleaning, use a touch-up pen (scratch repair pen) to cover the steel panel completely, let it dry, then apply wax and polish; 4. If the steel panel has started to rust: First sand the rusted area with fine sandpaper to remove rust and smooth the scratches, then use a touch-up pen to cover the steel panel completely, let it dry, then apply wax and polish.

How to adjust the time on a 2009 Peugeot 307?

2009 Peugeot 307 time adjustment method: 1. Turn the ignition switch to the ON position, press the MENU button (each press corresponds to an option) to select REGLAGESAFF (display adjustment); 2. Press the OK button, at this time ANNEE will flash, start adjusting the year, then adjust the month, date, and time in sequence; 3. After all adjustments are completed, press the ESC button to exit. The 2009 Peugeot 307 has a wheelbase of 2610mm, length of 4470mm, width of 1760mm, height of 1510mm, and a trunk capacity of 5.06L.

Should I Top Up or Replace the Antifreeze When It's Low?

Upon discovering low antifreeze levels, the first step is to verify whether there is a leak in the engine's cooling system. After a preliminary inspection, you can proceed to top it up. If there is a leak or the level keeps dropping, it's advisable to visit a repair facility for inspection and maintenance promptly. During the antifreeze maintenance and inspection process, check if the antifreeze has deteriorated or changed color. Typically, antifreeze should be replaced every 2 years or 40,000 to 60,000 kilometers, depending on the vehicle's actual condition. Antifreeze prevents the coolant from freezing during cold winter parking, which could otherwise crack the radiator or damage the engine cylinder block or head. It's essential to use antifreeze year-round.

What is the working principle of a torque sensor?

Working principle of torque sensor: It uses strain gauge electrical measurement technology to form a strain bridge on an elastic shaft for torque measurement. Application scope of torque sensor: 1. Detection of output torque and power of rotating power equipment such as motors, engines, and internal combustion engines; 2. Detection of torque and power of fans, water pumps, gearboxes, and torque wrenches; 3. Can be used to manufacture viscometers; 4. Can be used in process industries and flow industries. Precautions for installing torque sensors: 1. Do not operate with electricity, and never directly strike or collide with the sensor; 2. The fastening bolts of the coupling should be tightened, and a protective cover should be added outside the coupling to avoid personal injury.

What Causes the Rattling Noise in a Car Door Limiter?

Door limiter rattling noise is caused by wear and tear of the limiter. Applying some oil to the limiter for lubrication can resolve the issue. Below is the related introduction: Introduction to Door Opening Limiter: Commonly referred to as the limiter, it is a device that restricts the rotation of the door when subjected to a certain force. Function of the Door Opening Limiter: It limits the extent to which the door can open. On one hand, it restricts the maximum opening of the door to prevent it from opening too wide. On the other hand, it keeps the door open when needed, such as when the car is parked on a slope or during windy conditions, preventing the door from closing automatically.

How to Remove Crankshaft Bolts with Primitive Methods?

Insert two steel bars into the holes, then use a pry bar to leverage the two steel bars to loosen the bolts. Alternatively, measure the hole distance and weld an F-shaped wrench. Below is an introduction to the crankshaft: 1. Introduction: The crankshaft is the most important component in an engine. It receives the force from the connecting rod and converts it into torque, which is then output through the crankshaft to drive other engine accessories. 2. Function: The crankshaft is subjected to the combined effects of centrifugal force from rotating masses, periodically varying gas inertial forces, and reciprocating inertial forces, causing it to bear bending and torsional loads. 3. Requirements: The crankshaft must have sufficient strength and stiffness, with journal surfaces that are wear-resistant, operate uniformly, and have good balance.

Trending Ranking

How Far Can a Car Go When the Last Fuel Bar is Flashing?

What are the tips for safely storing gasoline in plastic containers?

How to Solve the Hot Water Problem for Showering in an RV?

What is the actual fuel consumption of the BMW X6?

What engine is used in the new X-Trail?

What Causes the Abnormal Noise When a New Car Turns?

How to Turn on the Air Conditioning While the Car is Parked?

What does it mean when the SET yellow light on the dashboard is on?

How to Check Online Whether a Car is New?

How to Handle 7 Points Deducted from a B2 Driver's License?

More Forum Discussions

How many times should the high and low beams be toggled?

What to Pay Attention to When Driving

How Many Fingers to Use When Pulling the Motorcycle Clutch?

How to Replace the Battery in an Audi Key?

Help

Cookie

Cookie Settings

© 2025 Servanan International Pte. Ltd.