Should a straight-going vehicle yield to a right-turning vehicle?

2 Answers
ChristianLynn
07/30/25 12:21am
Straight-going vehicles have the right of way. When a straight-going vehicle is traveling on the main road and a right-turning vehicle is preparing to merge from the auxiliary road into the main road, the straight-going vehicle on the main road has priority. If there is a right-turn guiding lane and signal, and the right-turning vehicles are released before the straight-going vehicles, the straight-going vehicles must yield to the turning vehicles. In other words, if both right-turning and straight-going vehicles have a green light, but the right-turning vehicles are released first, the straight-going vehicles must yield to the right-turning vehicles. Below are the relevant regulations: Relevant regulations: When a motor vehicle approaches an intersection without traffic signals or traffic police directing traffic, it must stop and look before entering the intersection, yielding to vehicles coming from the right. At intersections controlled by traffic signals: At intersections with designated lanes, vehicles must enter the appropriate lane based on their intended direction; vehicles preparing to enter a roundabout must yield to vehicles already in the roundabout.
Was this review help?
13
4
Share
OliveAnn
08/16/25 4:48am
I've been driving a private car for over a decade and often encounter this issue on the road. According to traffic regulations, vehicles going straight generally don't need to yield to right-turning vehicles; right-turning vehicles should proactively yield to through traffic, especially at signalized intersections or crossroads. This is because straight-moving vehicles travel at higher speeds with greater direct collision risks, and priority yielding helps prevent rear-end or side-impact accidents. In actual driving situations, I've seen some drivers make hasty right turns without checking mirrors, nearly colliding with through traffic - extremely dangerous behavior. My advice is to always slow down and check rearview mirrors plus blind spots before turning right, only proceeding when through traffic has safely passed. At complex unsignalized intersections, it's even more crucial to develop yielding habits - safety comes first. Remember that post-accident insurance premiums will skyrocket, not to mention time wasted on claims processing. Cultivating this protective habit safeguards both yourself and others, making driving more enjoyable.
Was this review help?
4
3
Share
Expand All
More Forum Discussions

How often should a China 5 diesel filter be replaced?

China 5 truck diesel filters should be replaced approximately every 10,000 kilometers. If the diesel filter malfunctions, sulfur elements can directly react with water to form sulfuric acid, which can corrode the internal components of the engine. Here is more information about diesel filters: 1. Diesel filter: It is one of the key components ensuring the quality of diesel entering the engine. Diesel filters are mainly divided into two types: spin-on and replaceable. 2. Function: High-quality diesel filters can effectively block microscopic dust and water carried in diesel, significantly extending the service life of fuel injection pumps, diesel nozzles, and other filtration components.
15
0
Share

What are the methods to address high airbag resistance?

The methods to address high airbag resistance are: 1. Check for short circuits and secure the wiring harness connections; 2. Fix the airbag plug; 3. Replace the airbag clock spring; 4. Replace the airbag reset ring. The reasons for high airbag resistance are: 1. Loose airbag wiring harness connections; 2. Loose airbag plug; 3. Burnt airbag clock spring; 4. Damaged airbag reset ring. The method to connect the airbag resistance is to unplug the airbag connector and use a 2-ohm resistor to connect the two wires to the resistor. The airbag consists of a collision sensor, cushion airbag, gas generator, and control unit. Its function is to allow the driver to come into contact with the airbag, and the damping through the airbag exhaust hole absorbs the collision force to protect the driver.
6
3
Share

What are the causes of brake pad noise?

The causes of brake pad noise are: 1. Insufficient contact surface, leading to increased pressure per unit area of the brake pad; 2. Emergency braking causing changes in the performance of the friction material; 3. Rust on the brake caliper; 4. Slow return of the brake master cylinder. The solutions for brake pad noise are: 1. Replace the brake pads; 2. Secure the brake caliper and spring; 3. Replace the brake disc. The steps for replacing brake pads are: 1. Remove the wheel of the brake; 2. Use a wrench to remove the brake caliper bolts and take out the brake pads; 3. Clean the debris from the brake caliper with a cloth; 4. Install the new brake pads onto the brake caliper; 5. Tighten the guide bolts and check the braking effect.
12
2
Share

Can You Continue Driving with a Flat Tire?

You cannot continue driving with a flat tire. The proper response methods are: 1. Park the vehicle on a flat surface and compare the tire pressure between the front and rear wheels on both sides; 2. Check around the tire for punctures, cuts, or if the rubber valve stem is aged or cracked; 3. If a sharp object is embedded, do not remove it; simply replace it with the spare tire. The impacts of low tire pressure include: 1. Increased friction coefficient with the road surface; 2. Heavier steering wheel and tendency to drift; 3. Increased movement in various parts of the tire, leading to abnormal heat due to excessive rolling; 4. Higher risk of tire blowout during high-speed driving; 5. Increased contact area, accelerating wear on the tire shoulders.
5
2
Share

How to Check Whether a Car Meets China 5 or China 6 Emission Standards?

How to check whether a car meets China 5 or China 6 emission standards: 1. Check the vehicle conformity certificate; 2. Check the environmental protection information accompanying the vehicle list; 3. Check the car production date. China 5 and China 6 refer to the fifth and sixth stages of national motor vehicle pollutant emission standards, respectively. Their purpose is to prevent pollution of the environment by exhaust gases from compression-ignition and gas-fueled spark-ignition engine vehicles, protect the ecological environment, and safeguard human health. The differences between China 5 and China 6 are: 1. Different nitrogen oxide emission standards: China 5 nitrogen oxide emission standard is 0.18 grams per kilometer; China 6 nitrogen oxide emission standard is 0.16 grams per kilometer. 2. Different particulate matter concentration emission standards: China 5 particulate matter concentration emission standard is 0.0045 grams per kilometer; China 6 particulate matter concentration emission standard is 0.022 grams per kilometer.
6
3
Share

What brand is Sakura tires?

Sakura is the brand name of Sakura tires. Here is some relevant information about Sakura: 1. It is one of the high-end brands developed by Cheng Shin Rubber (Xiamen) Group, specializing in bicycle tires, motorcycle tires, and bias tires, with a solid market foundation. 2. Sakura tires are a brand under Taiwan's Cheng Shin Rubber, which also owns brands like Cheng Shin, Maxxis, and Sakura. 3. When purchasing tires, it is advisable to opt for well-known brands as they generally offer better quality and after-sales service compared to smaller brands. However, it's not just about blindly choosing a big brand; it's important to determine which type of tire best suits your needs.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.