···
Log in / Register

Reasons for Frost on Car Windows in Winter

3 Answers
NathanFitz
08/31/25 7:50am
Frost on car windows in winter is caused by temperature differences. Methods for defrosting include the hard object method, the bedding cover method, and the preventive method, as detailed below: Hard Object Method: When the car windows are covered with frost or snow, use old cassette cases, CD cases, or expired credit cards, prepaid cards, or similar hard objects to scrape off the frost on the glass. Since these materials are much softer than glass, they are fast and do not damage the glass. Bedding Cover Method: After parking at night, cover the front and rear windshields with newspapers, old bed sheets, or old towels. In the morning, remove the cover, and there will definitely be no frost on the windshields. Preventive Method: After using the car for the day, do not immediately lock the car and leave. Instead, open both car doors to ventilate until the interior temperature drops to match the outside temperature, then lock the doors.
Was this review help?
9
1
Share
Tess
09/13/25 4:05am
It's really annoying to find a layer of frost on the windshield every winter morning! This is mainly caused by temperature differences: the air inside the car is warmer than outside, causing moisture in the air to condense into frost on the cold glass surface. Specifically, when you turn off the engine, the glass cools down quickly, but the residual heat and moisture inside the car (from breathing or evaporation from wet clothes) can't dissipate fast enough. When humidity builds up, frost forms. High humidity is also a key factor—frost is more likely to appear on rainy or snowy days. To prevent this, I make it a habit to open the windows for a few minutes before parking to let the moisture escape. Alternatively, I park the car facing the wind to reduce glass cooling. If frost has already formed, I turn on the defroster at full blast after starting the car and use a glass defroster for better results. Regularly clearing debris near the wipers also helps. These little tricks make winter driving much smoother for me.
Was this review help?
7
0
Share
Expand All
LaCharlotte
10/27/25 4:53am
Every time the temperature drops, my car windows get covered in frost, which feels really troublesome. The root cause is that the glass is too cold, and when it meets warm, moist air, the moisture freezes on contact. In winter, we often have the heater on inside the car, making the inner surface of the glass cold, so the moisture from our breath condenses and freezes instantly. It gets worse when the humidity is high. I remember one morning when the windows were completely white, and I could barely see the road. Now I've learned my lesson: before parking, I turn on the external air circulation or run the AC for a few minutes to reduce the humidity inside the car—simple and effective. If it's really cold, covering the windshield with a protector also helps. Regularly checking the window seals to prevent moisture from getting in is also a good habit. With these accumulated tips, dealing with frost has become much easier, and driving is safer too.
Was this review help?
7
3
Share
Expand All
More Forum Discussions

What Are the Essential Items on a Major Maintenance Checklist?

Replace engine oil and three filters, replace transmission fluid, replace generator and fan belts, replace spark plugs, replace brake fluid, replace power steering fluid, replace fuel filter element, inspect and replace tires, inspect and clean throttle body, check antifreeze, inspect and replace timing belt, inspect chassis, inspect and clean fuel injectors, check battery. Here is related information: 1. Vehicle Maintenance: Vehicle maintenance refers to the preventive work of regularly inspecting, cleaning, supplying, lubricating, adjusting, or replacing certain parts of a vehicle, also known as vehicle servicing. 2. The purposes are: The purposes of vehicle maintenance are to keep the vehicle clean and tidy, maintain normal technical conditions, eliminate potential hazards, prevent failures, slow down the deterioration process, and extend the service life.
5
0
Share

Should the speed be maintained above 20 throughout the entire Subject 3 test?

It is not necessary to maintain the speed above 20 throughout the entire Subject 3 test. Here is an introduction regarding the speed requirements for the Subject 3 test: 1. Gear and speed should match: When in first gear, the speed should be between 10–20 km/h; when in second gear, the speed should be between 20–30 km/h; when in third gear, the speed should be between 30–40 km/h; when in fourth gear, the speed should be above 40 km/h; when in fifth gear, the speed should not exceed 45 km/h. 2. Speed considerations for the Subject 3 test: During the Subject 3 test, it is important to maintain a consistent speed throughout, avoiding sudden acceleration or deceleration. Driving too slowly may cause the engine to stall, while driving too fast may result in penalties. Generally, the speed should not exceed 45 km/h or drop below 10 km/h.
14
1
Share

Why can't the Nissan Sylphy start?

The reasons why the Nissan Sylphy cannot start may include human operational factors such as a dead battery, empty fuel tank, or incorrect gear position; it could also be due to vehicle usage issues like improper fuel quality, lack of antifreeze, or excessive carbon buildup. The vehicle usage reasons are as follows: 1. Fuel quality issue: During a repair, it was found that the fuel tank contained water and mud. Using such fuel will inevitably damage the car. Therefore, car owners are reminded to always refuel at reputable gas stations and can carry a gauze to cover the fuel nozzle when traveling to filter out impurities. 2. Lack of antifreeze: Some car owners add water or inferior antifreeze to their cars, resulting in extremely cold winter conditions that freeze the entire water circuit, crack the engine, prevent the car's water pump from functioning, cause failure to start, and damage other engine components.
20
1
Share

What is the sequence of actions for getting off the car in Subject 3?

The sequence of actions for getting off the car in Subject 3 is: shift to neutral, pull the handbrake, reset the right turn signal, turn off the engine, release the clutch and brake pedals, unbuckle the seatbelt, and observe the left rear before getting off. Introduction to Subject 3: Subject 3 includes the road driving skills test and the safety and civilized driving knowledge test, which are part of the motor vehicle driver's license assessment. The content of the road driving skills test varies depending on the type of vehicle being licensed. Test Content: The road driving skills test for Subject 3 generally includes: preparation for getting on the car, simulated light test, starting, driving straight, gear shifting operations, changing lanes, parking by the side of the road, going straight through intersections, turning left at intersections, turning right at intersections, crossing pedestrian crossings, passing through school zones, passing through bus stops, meeting vehicles, overtaking, making U-turns, and driving at night. The safety and civilized driving knowledge test generally includes: requirements for safe and civilized driving operations, knowledge of safe driving under adverse weather and complex road conditions, emergency handling methods for situations such as tire blowouts, and knowledge of post-accident handling procedures.
9
3
Share

How to Align the Vehicle Correctly at the Entrance of the S-Curve in Subject 2?

To align the vehicle correctly at the entrance of the S-curve in Subject 2, ensure that the left and right sides of the vehicle are equidistant and perpendicular to the entrance of the S-curve. Below are the relevant details about the S-curve in Subject 2: 1. Practical Operation Method for the S-Curve in Subject 2: Before entering the left curve, drive the vehicle close to the right side, keeping the right side of the car aligned with the right line. When preparing to switch to the right curve, turn the steering wheel to the right, aligning the left front corner of the car with the left line until the vehicle safely exits the curve, then turn the steering wheel back to the right. 2. New Requirements for the S-Curve in Subject 2: Driving over the edge line results in failure; stopping midway also results in failure.
4
3
Share

When does the 30-second countdown start for hill start?

Hill start thirty seconds is counted from when the vehicle comes to a stop, and the vehicle must be started within 30 seconds. Below is an introduction to the related content of Subject 2: 1. Assessment content: The five assessment items are reverse parking, parallel parking, hill start, right-angle turn, and curve driving. 2. Requirements: Subject 2 requires 26 training hours, of which 2 hours are theoretical knowledge, so in practice, it is 24 hours. 3. After the vehicle stops: If the vehicle is not started within 30 seconds, it results in a failure. If the front bumper of the car or the front axle of the motorcycle is not aligned with the pole line and deviates by no more than 50 cm, 10 points are deducted. 4. After the vehicle starts: If the vehicle rolls back between 30 cm and 50 cm, 20 points are deducted.
16
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.