Reasons for Difficult Engine Starting

1 Answers
LeDonovan
07/28/25 6:55pm
Here are the specific reasons why a car may have difficulty starting: 1. Excessive carbon deposits leading to frequent malfunctions. When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold-start fuel injector can be largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts and making the engine hard to start. Only when the carbon deposits become saturated with gasoline does the engine start more easily. After starting, the gasoline adsorbed on the carbon deposits is then sucked into the combustion chamber by the engine's vacuum, making the air-fuel mixture too rich. The constantly fluctuating air-fuel mixture causes the engine to idle roughly after a cold start. 2. Low engine temperature. When the temperature inside the engine is insufficient, the fuel and lubricating oil cannot reach the required temperature. Therefore, during cold starts, more fuel should be injected to meet performance requirements. Poor fuel atomization at low temperatures leads to reduced ignition energy, affecting performance and causing the car to shake. Aging ignition coils, aging spark plug high-voltage wires, or electrical leakage can also reduce ignition energy.
Was this review help?
3
4
Share
More Forum Discussions

Which Method is Best for Car Tire Repair?

Among tire repair methods, the cold patch method is considered the best. Other methods include hot vulcanization repair, internal patch repair, plugging with rubber strips, and mushroom plug repair. More details about car tire repair are as follows: Cold Patch Repair: Cold patch repair involves thinning the inner side of the leaking hole on the tire. A specialized adhesive strip is then applied and repeatedly pressed to restore the tire to normal use. Hot Vulcanization Repair: Hot vulcanization is typically used for truck bias-ply tires. Passenger car tires should not be repaired this way, as the heating process can damage the tire crown and may not ensure sufficient strength. It should be avoided whenever possible. Internal Patch Repair: Larger tire specialty shops often use this method, which operates on a principle similar to bicycle tire repair. Plugging with Rubber Strips: This is the quickest and most convenient tire repair method. It involves directly inserting a rubber strip into the leaking hole using a nail, effectively sealing it and allowing the tire to be used normally in a short time. Mushroom Plug Repair: The mushroom plug is made from special materials with properties very similar to rubber. It is inserted into the leaking hole on the inner side of the tire and then smoothed out.
4
4
Share

What is the difference between AMT transmission and manual-automatic transmission?

Transmission is one of the important drivetrain components of a car, and its performance is a key parameter determining the vehicle's overall performance. Transmissions are mainly divided into manual transmissions and automatic transmissions. Among them, both AT and AMT belong to automatic transmissions. The specific differences between the two are as follows: 1. AT Transmission: The AT transmission consists of a valve body, oil pump, clutch, brake, one-way clutch, diaphragm spring, snap ring, steel plates, friction plates, large sun gear, small sun gear, planetary carrier, and ring gear. The structure of the AT transmission is complex and precise, and in actual vehicle installation, it needs to be connected to a torque converter. The AT-automatic transmission is mature in technology but has relatively higher fuel consumption. 2. AMT Transmission: The AMT transmission is essentially a manual transmission with automatic clutch and gear-shifting functions. Its structure is fundamentally the same as that of a traditional parallel-shaft manual transmission. The AMT transmission has relatively noticeable gear-shifting impacts (though advancements in electronic control technology have made gear-shifting actions and timing more precise, reducing the impact). It features a simple structure, high reliability, and ease of maintenance. Since it is essentially a manual transmission with added automatic clutch and gear-shifting mechanisms, it has more gear ratios, making it more adaptable to various complex working conditions. Ordinary AMT transmissions cannot amplify the input torque because they lack a torque converter. Only some heavy-duty transport vehicles, to cope with their specific working conditions, use AMT transmissions equipped with torque converters.
6
1
Share

What is B5?

B5 is a paper size specification. The commonly used B5 size is EXTRA, which follows the international standard dimensions of 176mm x 250mm. Additionally, there was another standard of 182mm x 257mm used in mainland China before 1982. Like other paper sizes, the establishment of an internationally standardized B5 size aims to regulate and unify paper dimensions, which holds significant importance for promoting foreign trade and international exchanges. Below is some extended information: A3: A3 paper refers to the internationally standardized A3 size, measuring 297mm × 420mm. A4: A4 paper is defined by the ISO 216 standard of the International Organization for Standardization, with dimensions of 210mm × 297mm. This international standard is adopted by the majority of countries worldwide for their paper sizes.
6
0
Share

What to Do If Your Sedan Is Recalled?

If it has been confirmed that your vehicle is within the recall scope, you can first call the local service station to inquire about the relevant information of this recall, such as the reason for the recall, potential fault symptoms and consequences, and what preventive or emergency measures should be taken before the recall repair. At the same time, schedule a repair appointment and proceed with the repair at the scheduled time. The differences between a recall and the three guarantees (repair, replacement, and refund) are as follows: 1. Different in nature: The purpose of a recall is to eliminate the safety hazards posed by defective vehicles to the entire society and to safeguard public safety; the purpose of the three guarantees is to protect the legitimate rights and interests of consumers. During the product liability warranty period, when quality issues arise with the vehicle, the manufacturer is responsible for resolving them free of charge for the consumer, thereby reducing the consumer's losses. 2. Different legal bases: Recalls are based on the "Product Quality Law" for defective automotive products that may pose a threat to public personal and property safety, aiming to maintain public safety, public interests, and social economic order; for businesses, the three guarantees are a special form of contractual liability in legal terms. According to the "Product Quality Law," for products with quality issues within the three-guarantee period, the state has formulated relevant "three-guarantee regulations," under which sellers are responsible for repair, replacement, or refund, thereby bearing the product warranty responsibility.
4
3
Share

Will Forced Downshifting in a Manual-Automatic Transmission Damage the Vehicle?

Forced downshifting in a manual-automatic transmission can, to some extent, damage the vehicle and affect its lifespan. Below is a detailed introduction to manual-automatic transmissions: 1. Overview: A manual-automatic transmission combines manual and automatic shifting modes. The manual mode allows for free adjustment of gears and RPM, providing a more convenient and sporty driving experience with enhanced driving pleasure. However, manual-automatic transmissions require higher maintenance costs and stricter usage conditions. 2. Additional Information: It is advisable to use the manual mode during high-speed driving, as it not only accelerates faster but also allows for engine braking during emergency braking.
5
1
Share

What are the length, width, and height of a sedan's trunk?

Generally, the dimensions of a sedan's trunk are approximately 1120 mm in depth, 1010 mm in width, and 560 mm in height. Here is some related information: 1. Trunk: The trunk is the area in a small car used for storing miscellaneous items, typically located at the rear of the vehicle. 2. Considerations: The trunk is a very important component of a vehicle's interior configuration, and effectively utilizing its space requires certain techniques. The order in which items are placed is crucial. The principle is to place large items at the bottom and small items on top, as well as to place heavy items in the front and lighter items at the back.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.