Must You Wait for the Voice Prompt Before Starting in Subject 2?

2 Answers
DelAnastasia
07/24/25 12:16pm
You must wait for the voice prompt before starting in Subject 2. If any part of the Subject 2 test is failed, the voice prompt will instruct the examinee to return to the waiting area and start over, indicating the beginning of the second attempt. Therefore, continuing with the reverse parking or proceeding to the next item is incorrect. During the Subject 2 test, always follow the voice instructions. Start only after hearing the "Start the test" voice prompt: After getting into the car and completing the preparations, start driving to the test area only after hearing the "Start the test" voice prompt. Upon entering the test area and reaching the test item point, the car will usually play a voice prompt like "XXX item, start the test." It is best to wait for the voice announcement before starting the test to avoid affecting the test results. Additionally, in some cases, the voice announcement may be delayed, but this does not affect the test results. Such situations are usually rare, and candidates should stay calm and provide timely feedback. Precautions during the Subject 2 test: If the "Start the test" announcement plays while adjusting the mirrors or seats, do not panic. You can continue with the preparations, as there is no time limit. Start the test only after completing the preparations. Many people fail the test because they panic and start hastily upon hearing the "Start the test" announcement during preparations, without completing the necessary preparations.
Was this review help?
3
0
Share
Faunus
08/11/25 6:24am
Regarding the Subject 2 driving test, from my perspective of regularly paying attention to driving test regulations, this matter is quite important. Specifically, in the Subject 2 test, you must wait until the voice instruction is fully completed before starting to move or take action. The test system will issue clear commands, such as "Please begin reversing into the parking space" or "Prepare for hill start." These voice prompts are automatically controlled by the computer, aiming to ensure each action is performed safely and orderly. If you start moving before the voice instruction finishes, the examiner's system will record it, likely resulting in point deductions or a failure, as it demonstrates rule-breaking or impatience. In practice, I've seen some students, due to nervousness, not fully listening to the instructions, leading to misaligned parking positions and point deductions. Therefore, I recommend everyone develop good habits during practice—focus on listening to the instructions during the test, operate slowly, and avoid rushing—to prevent unnecessary mistakes and improve pass rates. In summary, Subject 2 not only tests driving skills but also patience and discipline.
Was this review help?
10
1
Share
Expand All
More Forum Discussions

Where is the air conditioning filter located in a truck?

The air conditioning filter is located behind the glove compartment on the passenger side. Below is relevant information about the air conditioning filter: 1. Function: It ensures the filter fits tightly against the housing to prevent unfiltered air from entering the cabin. It separates solid impurities from the air such as dust, pollen, and abrasive particles. 2. Precautions: The air conditioning filter is prone to accumulating a lot of dust. Use compressed air or similar methods to blow away loose dust—never wash it with water, as this can easily damage it. After prolonged use, the activated carbon filtration function of the air conditioning filter will diminish, so it is recommended to replace the air conditioning filter at a 4S shop.
15
3
Share

What is the standard dimension for a 90-degree turn in the C1 driving test?

The standard dimension for a 90-degree turn is the wheelbase plus 1 meter. For training vehicles (typically Santana models), the C1 test vehicle dimension follows the same rule: wheelbase +1m. Santana specifications: length 4546mm, width 1710mm, height 1427mm, wheelbase 2548mm. The C1 driver's license permits operation of: small and micro passenger vehicles; light and micro cargo trucks; light/small/micro special purpose vehicles; passenger vehicles seating ≤9 persons. Vehicles excluded from C1 license: large buses, tractors, city buses, medium buses, heavy trucks, regular trikes/motorcycles, mopeds, wheeled machinery, trolleybuses, trams. Additionally, C1 prohibits vehicles with >9 seats or trucks exceeding 6m total length.
10
0
Share

Are out-of-town green license plates subject to traffic restrictions in Shenzhen?

In Shenzhen, out-of-town green license plates are subject to traffic restrictions. Here is some relevant information about green license plates: Meaning: Green license plates refer to hybrid and pure electric vehicles. Conditions for obtaining a green license plate: To obtain a green license plate, you must first have a new energy vehicle. New energy vehicles include hybrid electric vehicles, pure electric vehicles, solar-powered vehicles, and other types of new energy vehicles that meet certain conditions. These vehicles are eligible for green license plates. Additionally, vehicles with green license plates not only avoid purchase restrictions in some major cities but also enjoy various subsidy policies and are exempt from traffic restrictions.
6
5
Share

What are the reasons for the ABS light in a Skoda being on?

There are various states in which the ABS light may illuminate, with different causes and solutions for each state, as detailed below: State 1: ABS warning light stays on (most common). Cause 1: The ABS speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle's speed and the wheel's slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the speed sensor and adjust the gap between the speed sensor and the signal ring to restore normal function. Cause 2: Poor signal quality due to loose connections between system wires or poor contact in the ABS relay, leading to system failure. Solution: Check the wire connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates, but turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases, the voltage rises, and the ABS indicator light turns off. The ABS system's power supply voltage is too low, possibly due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body's wire connector; ABS computer malfunction. Solution: Loosen the grounding screw of the hydraulic valve body, then retighten it, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer calculates a significant difference between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the sticker near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, push the brake switch linkage down fully with a finger, then release the brake pedal to complete the self-setting position; replace the brake light switch. If the ABS warning light is on, it is advisable not to continue driving. The illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, making it difficult for the driver to slow down or adjust the vehicle's trajectory, posing significant safety risks.
14
1
Share

When will Guangxi implement the China VI emission standard?

Guangxi began implementing the China VI emission standard on January 1, 2020. Implementation plan for China VI emission standard: Phase 1: From July 1, 2020, all vehicles sold and registered must comply with China VI-A standard; Phase 2: From July 1, 2023, all vehicles sold and registered must comply with China VI-B standard; Early implementation in some regions: Some cities implemented the China VI emission standard for light-duty vehicles as early as January 1, 2019. For example, Guangzhou implemented the China VI standard for light-duty gasoline and diesel vehicles from March 1, 2019; Shenzhen required light-duty diesel vehicles to meet China VI standard from July 1, 2018, and light-duty gasoline vehicles to meet China VI standard from July 1, 2019.
12
2
Share

Is It Illegal to Change the Bumper Style?

If the modification of the bumper is not approved by the traffic management department in advance, it is illegal, and the vehicle cannot be driven on the road or pass the annual inspection normally. According to the relevant provisions of the current "Motor Vehicle Registration Regulations," any changes to the body color, model, performance, purpose, and structure of a licensed motor vehicle, as well as the replacement of the frame, body, or engine, must be applied for change registration with the vehicle management office. Actions such as installing a spoiler, adding a full body kit, or modifying the exhaust pipe are, in principle, not allowed. Below is more information about car bumpers: 1. Function: The front and rear ends of a car are equipped with bumpers, which not only have a decorative function but are also important safety devices that absorb and mitigate external impacts, protecting the car body and the safety of passengers. 2. Structural composition: The outer panel and buffer material are made of plastic, and the crossbeam is pressed into a U-shaped channel from cold-rolled sheet metal about 1.5 mm thick. The outer panel and buffer material are attached to the crossbeam, which is connected to the longitudinal beams of the car frame with screws and can be disassembled at any time. 3. Non-compliant products: According to tests by authoritative quality inspection departments, the consequences of damages caused by products that do not meet the industry standard for "Automobile Protective Bumpers" shall be legally borne by the production enterprises and sellers.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.