Must the tire pressure of all four car tires be the same?

1 Answers
DeBethany
07/30/25 6:22am
Car tire pressure does not have to be the same for all four tires. The normal tire pressure range is 2.2 to 2.8 bar. It is sufficient to maintain the front tire pressure at 2.4 bar and the rear tire pressure at 2.3 bar. In winter, you can appropriately increase the pressure by 0.1 bar, and in summer, decrease it by 0.2 bar to prevent tire blowouts. Functions of tires: 1. Generate driving force, braking force, and lateral force through interaction with the road surface; 2. Bear the weight of the car; 3. Provide cushioning and shock absorption. Steps for replacing a new tire: 1. Use a jack to lift the car to a certain height; 2. Remove the screws and take off the old tire; 3. Install the new tire and release the jack.
Was this review help?
3
0
Share
More Forum Discussions

Do Cars Have a Reserve Fuel Tank?

Cars generally have a reserve fuel tank. The methods to open the fuel tank are as follows: Mechanical key opening: This is usually seen in some rugged off-road vehicles. Modern family cars generally do not use mechanical keys for opening because it is relatively complicated to operate. In-car switch method: The in-car fuel tank switch is located in different positions depending on the car model. Some may be on the floor to the left of the driver's seat, some on the left front door panel or the central console, all marked with a fuel pump symbol. However, it's important to note that the in-car switch can easily lead to the owner forgetting to turn off the engine before refueling, so always remember to turn off the engine before refueling. Press-to-open method: The press-to-open fuel tank door is currently the most convenient method. The owner only needs to park the car, and the fuel attendant can press to open the tank for refueling. However, when not parked for refueling, always remember to lock the central control, otherwise the fuel tank cap can be opened.
11
3
Share

Why is one side of the car air conditioning cold while the other is not?

One side of the car air conditioning being cold while the other is not is due to a fault in the air vent, where one of the servo motors of the air vent is damaged, causing one side of the air conditioning to not cool. Another reason could be that the air valve plate is stuck, hindering its rotation and affecting the airflow on one side, or there might be a blockage in one of the air conditioning ducts. Solutions for one side of the car air conditioning being cold while the other is not: If the issue is with the air vent, the servo motor of the air vent needs to be replaced. If the air valve plate is stuck, it is necessary to visit a repair shop for inspection and repair. Maintenance methods for car air conditioning: Regularly check the refrigerant and compressor oil, clean the surface of the condenser, and clean the surface of the evaporator. The car air conditioning system, abbreviated as car AC, consists of a refrigeration system, heating system, ventilation and air purification devices, and a control system. Functions of car air conditioning: It adjusts and controls the temperature, humidity, air cleanliness, and airflow inside the car cabin to a comfortable state, providing a pleasant riding environment for passengers and reducing travel fatigue. It also creates favorable working conditions for the driver and plays a crucial role in ensuring safe driving as a ventilation device.
13
5
Share

Abnormal Noise from Car Air Conditioner Blower?

It may be caused by the blower blades hitting debris. Here is a detailed introduction to the relevant content: Introduction: The car air conditioning system includes the compressor, dryer, evaporator, high and low pressure pipes, and expansion valve. Typically, the air conditioning cycle involves four processes: compression, condensation, expansion, and evaporation. Ordinary air turns into low-temperature, low-pressure gas after these processes, and the blower's role is to blow this gas out through the air conditioning vents. Troubleshooting: Remove the dust filter cover on the drain trough cover and take out the dust filter. Turn on the blower switch to make it rotate, and observe that there is no debris around the blower impeller, indicating that the noise is not caused by the first reason. After removing the central vent, listen again and feel that the noise is coming from inside. Remove the entire dashboard, then take out the middle connecting piece of the air conditioning duct. It is found that there is a layer of sponge attached to the temperature adjustment flap, with a black plastic film glued to it. Half of this plastic film has separated from the sponge on this car, and when the blower is working, this black plastic film flutters in the airflow, causing the abnormal noise.
16
4
Share

Can Car Window Tinting Be Redone If Not Done Properly?

If there are issues during the tinting process, such as impurities in the film, you can request a redo. Below is a detailed introduction to the relevant content: Tinting steps: Clean the glass, spray a small amount of installation liquid on the outer surface of the glass, cover it with the window film, and trim the film along the edges. Use a portable heat gun to precisely shape and shrink the film. After heat shaping, clean the inner surface with a strong liquid cleaner and scrub off the oil with a nylon soft pad. Remove the protective film, spray installation liquid on the adhesive surface of the window film and the inner surface of the glass, apply the film to the glass, reposition it, spray installation liquid again, and use specialized tools to remove the installation liquid. Precautions: Avoid washing the car within three days after tinting to prevent the film from peeling off due to moisture. After tinting, do not roll down the side windows for 24 hours in summer and 48-72 hours in winter. The film, not yet fully bonded, is prone to displacement. If bubbles are found, they should be addressed within 24 hours at a professional car beauty and maintenance shop. After applying sun protection and heat insulation film, avoid using strongly adhesive labels directly on the film for one month.
20
4
Share

Under What Circumstances Should the Car's Eco Mode Be Used?

Car's eco mode is used in urban traffic congestion conditions. The eco mode is divided into active eco driving mode and non-active eco driving mode. The active eco mode usually has a button, allowing the owner to choose whether to enable it. The non-active eco mode does not have a dedicated button and serves to remind the owner to save fuel. When optimal fuel supply is achieved, the dashboard will display a green 'eco' indicator. If the accelerator is pressed hard for rapid acceleration or when encountering uphill sections, the 'eco' indicator will disappear. The working principle of the eco mode mainly involves analyzing various configurations that affect fuel consumption, such as transmission gear, engine speed, braking system, and transmission oil temperature, through various sensors. Then, the ECU calculates a lower fuel supply for the engine, effectively reducing fuel consumption compared to normal driving mode. Whether the car engine operates at long-term idle or high-speed driving, carbon deposits will form. The carbon deposits produced when working in eco mode are basically similar to those in normal operation. Carbon deposits increase only when the engine's air-fuel mixture is too rich, combustion is poor, or when low-quality fuel is used. Therefore, the eco mode can be used with confidence when enabled.
20
1
Share

Why is the electric forklift not responding to lifting?

Check if the battery voltage of the electric forklift accessories is too low. Below are the detailed explanations of the relevant content: Possible causes: Check if the electric forklift drive system accessories such as switches and wiring are loose or short-circuited, and if the micro switch is damaged. Check if the drive contactor assembly of the electric forklift accessories is burnt out, or if there is a short circuit, open circuit, or poor contact in the coil. Check if the drive module is burnt out or if there is a short circuit or open circuit. Solutions: Repair and clean the wiring, replace or repair the micro switch; repair the platinum contacts of the electric forklift contactor or directly replace it with a new hydraulic contactor assembly; repair or replace the module assembly.
4
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.