Must the dowry car be brand new?

1 Answers
EllieFitz
07/30/25 7:19am
The dowry car does not necessarily have to be brand new. Here are some relevant considerations regarding the use of new cars: Avoid overloading: Carrying too much weight during the break-in period can damage the mechanical components of a new car. Since the power transmission parts of a new car have not yet fully broken in, aggressive acceleration can cause irreversible damage. Therefore, it is essential to follow the principle of "slow and steady" during the break-in period. Speed limits for new cars: For domestic cars, the speed limit is generally between 40-70 km/h, while for imported cars, it is around 100 km/h. When the throttle is fully open, the speed should not exceed 80% of the maximum speed. The recommended engine speed during the break-in period is between 2,000-4,000 rpm.
Was this review help?
16
1
Share
More Forum Discussions

How to remove ETC without damaging the car film?

The methods to remove ETC without damaging the car film are: 1. Use a hair dryer to heat the contact surface between the ETC device and the glass to soften it, then gently remove it; 2. Soak a towel in hot water and heat the adhesive tape on the back of the device; 3. Use a scraper to remove the adhesive tape and take it off. After installing the ETC, the owner should not remove it at will. There is an anti-removal mark on the back of the ETC. If the ETC is accidentally removed, the electronic tag will become invalid, and it must be reactivated by the staff at the customer service center. Otherwise, the ETC will not be usable the next time the car passes through the ETC lane for toll collection.
19
0
Share

What to Do When the Roewe RX5 Car Runs Out of Battery?

If the Roewe RX5's battery is dead, you can use jumper cables to charge it. The precautions for using jumper cables are: 1. Before connecting the jumper cables to the power-supplying vehicle, turn off its engine first; 2. After connecting the jumper cables to the power-supplying vehicle, ensure that the positive and negative terminals do not come into contact, as a short circuit is very dangerous; 3. When removing the jumper cables, disconnect the negative terminal first, followed by the positive terminal. Taking the 2020 4G Internet Million Edition Roewe RX5 as an example, it is equipped with a 1.5L turbocharged engine, delivering a maximum horsepower of 169 PS, a maximum power of 124 kW, and a maximum torque of 250 Nm, paired with a 6-speed manual transmission.
9
0
Share

Which engine oil is best for Nissan Sylphy?

Nissan Sylphy performs well with mineral engine oil. The functions of engine oil are: 1. As a lubricant, it reduces friction and wear between moving parts; 2. As a coolant, it absorbs heat generated in the engine combustion chamber and piston crown, cooling the engine and preventing overheating; 3. As a sealant, it fills the gap between piston rings and cylinder liners to prevent combustion pressure leakage. The Nissan Sylphy is a 4-door, 5-seater compact sedan with body dimensions of 4631mm in length, 1760mm in width, and 1503mm in height, a wheelbase of 2700mm, a fuel tank capacity of 50 liters, and a trunk capacity of 510 liters.
15
3
Share

Where is the turn signal fuse located in the Nissan Sylphy?

The turn signal fuse in the Nissan Sylphy is located in the fuse box in the front engine compartment. The turn signal is an indicator light that alerts vehicles and pedestrians when the vehicle is turning. It uses a xenon lamp tube and is controlled by a single-chip microcomputer circuit, operating with alternating left and right flashes. Taking the 2021 manual comfort version of the Nissan Sylphy as an example, its body dimensions are: 4631mm in length, 1760mm in width, and 1503mm in height, with a wheelbase of 2700mm and a fuel tank capacity of 50 liters. The 2021 manual comfort version of the Nissan Sylphy features a MacPherson independent front suspension and a torsion beam non-independent rear suspension. It is equipped with a 1.6L naturally aspirated engine, delivering a maximum horsepower of 122ps, a maximum power of 90kW, and a maximum torque of 155Nm.
11
4
Share

How many bottles of fuel additive should be added at one time?

Only one bottle of fuel additive should be added at a time. For new vehicles with less than 20,000 kilometers of mileage, it is unnecessary to add fuel additive. For vehicles exceeding 20,000 kilometers, it should be added as needed, typically one bottle per tank of fuel. Long-term use of fuel additive is harmful to the engine, and excessive use can increase carbon deposits in the combustion chamber, even leading to engine knocking or detonation, and worsening vehicle exhaust emissions. The functions of fuel additive are: 1. Remove carbon deposits from the car; 2. Reduce abnormal engine wear; 3. Improve atomization efficiency; 4. Reduce vehicle emissions; 5. Extend the service life of the car engine; 6. Clean the fuel system.
4
4
Share

What are the main components of the crank connecting rod mechanism?

The main components of the crank connecting rod mechanism are: the engine block group, the piston connecting rod group, and the crankshaft flywheel group. Its function is to convert the reciprocating motion of the piston into the rotational motion of the crankshaft, while converting the force acting on the piston into the torque output by the crankshaft to drive the rotation of the car wheels. The differences between the engine block group, the piston connecting rod group, and the crankshaft flywheel group are: 1. The engine block group consists of: the cylinder block, cylinder gasket, cylinder head, crankcase, cylinder liner, and oil pan. 2. The piston connecting rod group consists of: the piston, piston rings, piston pin, and connecting rod. 3. The crankshaft flywheel group consists of: the crankshaft, flywheel, torsional damper, and balance shaft.
6
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.