Methods to Test Vehicle Pulling

Where is the handbrake of Volkswagen Lavida?

The electronic handbrake button of Lavida is located at the top of the row of buttons on the left side of the gear lever. There is a letter 'P' on this button. Pulling the button upward engages the handbrake, while pressing it downward releases the handbrake. The operation of the electronic handbrake button is similar to that of the window lift buttons. Here are some related introductions: 1. Button type: Some cars' electronic handbrake buttons can only be pressed. Pressing it downward once engages the handbrake, and pressing it again releases the handbrake. 2. Electronic handbrake: Cars equipped with electronic handbrakes generally have electronic handbrake motors on both rear wheels. After engaging the handbrake, the handbrake motors on the rear wheels will clamp the brake pads, preventing the car from rolling. 3. Mechanical handbrake: Some cars use a mechanical handbrake, which has a simple structure. Inside the car, there is a handbrake lever with two cables behind it. Pulling the lever will engage the brakes on the two rear wheels.

6

5

Share

What's the reason for the Jinbei vehicle's sluggish acceleration and muffled performance when refueling?

This situation may occur due to damage to certain sensors around the engine, or damage to certain components around the engine. The most likely causes are a faulty throttle body or mass air flow sensor. Here is additional information: 1. Engine fuel system: The engine fuel system is a common problem area in vehicles. Clogged fuel injectors, leaking fuel lines, reduced fuel pump power, or a blocked fuel filter can all lead to poor vehicle performance. In addition to fuel, the engine also requires air. If components like the air filter or throttle body are clogged or malfunctioning, resulting in insufficient air intake, it can also cause sluggish acceleration and slow speed increase. 2. Crankshaft position sensor failure: This can cause the vehicle to lose the timing of ignition and fuel injection, putting the vehicle into a limp mode with poor acceleration. Replacing the sensor can fix the issue. A damaged fuel pump or fuel pump pressure leakage, leading to insufficient fuel pressure and inadequate fuel supply, will naturally result in poor acceleration. Replacing the fuel pump can resolve this. A clogged fuel pump filter can also cause insufficient fuel pressure, and replacing the filter can fix the problem.

14

3

Share

What is the B2 night driving light usage tutorial?

B2 night driving light usage methods: 1. Correctly turn on lights during night driving: Use low beams when following another vehicle closely in the same direction, alternately use high and low beams when navigating sharp curves, slopes, arched bridges, crosswalks, or intersections without traffic signals. 2. Properly use low beams when turning at intersections: Alternate between high and low beams when overtaking to alert the vehicle being passed, use low beams when driving on well-lit roads with streetlights. 3. Night driving light simulation test begins: Turn on vehicle lights, activate low beams, drive on unlit roads at speeds exceeding 30 km/h, switch from low beams to high beams, when there's a vehicle ahead traveling in the same direction at close range. 4. Alternate between high and low beams three consecutive times as a signal: Now driving on well-lit roads with streetlights, correctly use low beams when overtaking the vehicle ahead. 5. Now driving on unlit roads: Speed exceeds 30 km/h, correctly use high beams, when an oncoming vehicle approaches, prepare to meet, switch from high beams to low beams.

18

2

Share

How to Solve the Electronic Steering Lock Failure of Baojun 510?

Electronic steering lock failure may be caused by low car voltage, the steering column lock not being opened, or the remote key not matching the system, which can also lead to the failure. You can try pressing the start button twice to reconnect the power. If the problem persists, go to a repair shop to read the fault code and perform repairs based on the fault code, using a decoder for diagnosis. More related information is as follows: 1. Electronic steering lock failures are usually caused by the following reasons: the oil cup is too dirty, the filter screen is clogged, or the oil level in the oil cup is low; there is a large amount of air in the power steering system; foreign objects in the steering system cause the steering pump flow control valve to stick; insufficient tire pressure, interference with the steering column, loose connections, loose or slipping pump belt, or loose pump installation position; loose bolts at the connection points of the oil pipes, causing steering fluid leakage; excessive wear of the steering gear piston cylinder, poor sealing of the oil seal, sticking or damage of the control valve. 2. Occurrence of deviation: Electronic steering lock failure can cause the car to deviate during driving, meaning the car steering wheel remains stationary, and the car will automatically move to one side. It can also result in heavier steering, making it very difficult to turn the steering wheel left or right.

10

2

Share

Why Does Factory Paint Bubble?

Factory paint bubbles for the following reasons: 1. Poor paint quality: This issue often occurs at roadside shops that substitute inferior products, selling so-called factory paint at low prices while actually using substandard materials. 2. Improper application conditions and process: Paint application requires strict technical standards and professional environments operated by specialists, otherwise bubbling easily occurs. 3. Excessive paint thickness: Inattentiveness during spraying or technicians' limited skills often result in overly thick paint layers that cause sagging beneath the surface.

12

0

Share

Is 120°C Oil Temperature Normal for a BMW 5 Series?

For a BMW 5 Series, an oil temperature within 120°C is considered appropriate, while temperatures above 120°C are abnormal. Under normal circumstances, the operating temperature of the engine oil in a BMW 5 Series typically ranges between 70°C and 90°C. However, during aggressive driving, the engine operates under high load, causing the temperature to rise slightly, reaching around 100°C to 110°C. Therefore, an oil temperature of 100°C is quite normal. Below is an introduction to the oil temperature in the BMW 5 Series: 1. High Coolant Temperature: This is a fault phenomenon caused by increased internal pressure in the coolant pipes due to high engine coolant temperature. Apart from high coolant temperature, the engine oil can also experience high temperature issues. This is closely related to the antifreeze. 2. High Antifreeze Temperature: Excessive antifreeze temperature can also elevate the oil temperature (oil temperature being higher than coolant temperature). When the oil temperature is too high (coolant temperature also rises, reducing heat dissipation), the thermal stability of the oil under high-temperature conditions is severely tested. This is why some oils become thinner at high temperatures, leading to oil burning phenomena.

13

5

Share

Methods to Test Vehicle Pulling

Where is the handbrake of Volkswagen Lavida?

What's the reason for the Jinbei vehicle's sluggish acceleration and muffled performance when refueling?

What is the B2 night driving light usage tutorial?

How to Solve the Electronic Steering Lock Failure of Baojun 510?

Why Does Factory Paint Bubble?

Is 120°C Oil Temperature Normal for a BMW 5 Series?

What are the functions of each gear in a manual transmission?

What to Do When Your Driver's License Points Are Depleted and You're Stopped by Traffic Police?

Can You Drive the Next Day After Drinking at Night?

Where is the air conditioning filter located in the Ford Mondeo Zhisheng?