Methods for Repairing Minor Scratches on Car Body

1 Answers
TuckerMarie
07/30/25 6:56am
First, clean the area to be repaired with water, ensuring no wax residue or grease remains, as these can reduce the adhesion of the paint. If the scratched area has rust, gently remove it with emery cloth. Then, pour the paint into a small dish and carefully apply it dot by dot using a fine brush tip. Wait for the first layer of paint to dry before applying the next layer, continuing until the repaired area is slightly raised compared to the surrounding undamaged surface. Be careful not to apply paint outside the scratched area. Once the paint is dry, use fine sandpaper with water to sand down the raised area until it is level with the surrounding surface. Finally, wrap some emery cloth around your finger for a final polish.
Was this review help?
14
1
Share
More Forum Discussions

How Long Should a Novice Driver Wait Before Driving on the Highway?

Novice drivers must wait at least one year before they can drive on the highway independently. Here are some important considerations for new drivers on the highway: 1. Accompaniment Required: During the probationary period, a novice driver must be accompanied by a licensed driver who has held a valid driver's license for the same or higher vehicle category for at least three years. 2. Penalties: According to Article 65, Section 2 of the "Decree No. 123," driving without a qualified accompanying driver or with an unqualified accompanying driver will result in a fine of 200 yuan and an order to exit the highway at the nearest exit. Novice drivers attempting to enter the highway will be educated and advised to turn back.
18
1
Share

What does the black license plate with Jing A mean?

Jing is the abbreviation for China's capital, and Jing A is the earliest issued vehicle license plate. Black license plates are for foreign vehicles. Below are the relevant details: 1. Issuance Scope: Black license plates are issued to foreign enterprises (including those from Hong Kong, Macao, and Taiwan), foreign and international organizations stationed in China, vehicles purchased by foreigners in their personal names for use in China, vehicles entering from Hong Kong, Macao (Taiwan), and foreign countries, as well as temporary license plates for customs-seized vehicles or confidential institutions. 2. Matters Regarding the Installation of Motor Vehicle License Plates: Motor vehicle license plates can be directly installed on the vehicle body or mounted using a standardized license plate frame, provided that such a frame cannot be easily removed and must use a sealing device to secure the screw caps to prevent unauthorized removal. License plate frames must not use external, internal lock, electronic automatic shielding, or replaceable types that facilitate easy removal or replacement.
16
2
Share

How many hours does it generally take to charge a car battery?

Generally, the charging time of a car battery is related to the charging equipment. Professional charging equipment requires 2-4 hours, while a normal charger usually takes 6-8 hours for a full charge. Below are the usage methods for car batteries: 1. Develop good in-car electricity habits: To maintain the vehicle battery, the most important thing is to develop good electricity habits. Avoid listening to the radio loudly, charging your phone, or using a charging pump when the engine is off. Over time, this can easily drain the battery, and frequent battery depletion will significantly reduce its lifespan. 2. Regularly drive on highways for long distances: There are many benefits to regularly driving on highways, not only can it remove carbon deposits from the vehicle, but it can also fully charge the battery. Generally, driving on the highway for more than an hour can fully charge the car battery, keeping it in optimal condition. 3. Do not leave the car unused for long periods: If the car is not used for a long time, the battery cable should be disconnected, or the vehicle should be started and driven for dozens of kilometers every two weeks to ensure the battery can function normally.
13
1
Share

What is the normal fuel tank pressure?

The fuel pump pressure should be 284-325kpa. The following is a related introduction about the fuel tank: 1. Function: In addition to storing fuel, the fuel tank also plays roles in heat dissipation, separating air bubbles in the fuel, and settling impurities in the hydraulic system. There are two types of fuel tanks: open tanks and closed tanks. Open tanks have a simple structure and are easy to install and maintain, making them commonly used in hydraulic systems; closed tanks are generally used for pressurized fuel tanks. 2. Structure: The fuel tank usually has two outlets: one is the fuel filler neck that is directly visible, and the other is used to install the fuel pump and fuel metering device. The fuel tank is a relatively sealed system, often equipped with ventilation devices to prevent deformation caused by excessive fuel consumption and the resulting pressure difference between the tank and the atmosphere. Early fuel tanks were mostly made of metal materials, but later, synthetic materials were increasingly used to meet the requirements of lightweight and structural design.
10
2
Share

What to do with ETC after vehicle transfer and license plate change?

If you need to handle the ETC license plate change, you should bring the license plate change procedures, along with your ID card and vehicle license, to the original bank processing point or any ETC processing point established by the highway department to handle the change business. The ETC installation process is as follows: Upon receiving the device, first check whether the ETC card and electronic tag (OBU) are damaged. Press the anti-tamper button on the back of the OBU. The red light will briefly light up, and the OLED screen will display "Tag Invalid" and "Please Insert Card," indicating the device is functioning normally. Clean the front windshield to ensure the glass surface is smooth, clean, and dry. Then peel off the OBU adhesive backing film, stick it to the installation position, and press it with your hand for 2-3 minutes to remove any air bubbles. Insert the ETC card with the front side facing the driver and the back side facing the front glass, ensuring the chip is inserted into the OBU device.
16
0
Share

Why Do Car Headlights Keep Flashing?

Reasons for car headlights flashing: 1. Poor circuit contact. 2. Stabilizer malfunction. 3. Issues with bulbs or high-voltage coils. Introduction to car headlights: 1. Definition: Car headlights, also known as automotive front lights or LED daytime running lights, serve as the "eyes" of a vehicle. They not only affect the owner's external image but are also crucial for safe driving at night or in adverse weather conditions. 2. Historical background: The use and maintenance of car lights should not be overlooked. It is said that the first car headlight was a household portable lamp. In 1898, the Columbia electric car applied electricity to front and rear lights, marking the birth of automotive lighting.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.