Main Test Content of Subject 3?

1 Answers
RubyLynn
07/29/25 8:26pm
Subject 3 test content is as follows: 1. Preparation before starting: Candidates must follow the safety officer's instructions, approach the vehicle, walk around it (from the left front door to the back), and confirm safety before opening the door to get in. After entering, first adjust the seat to a suitable position, adjust the interior and exterior rearview mirrors, and fasten the seat belt. Then perform fingerprint verification; the fingerprint scanner is located below the left air vent on the steering wheel. 2. Starting: Upon hearing the voice prompt "Please start," press the clutch, shift into first gear, turn on the left turn signal (for more than 3 seconds), and observe the left rearview mirror (turning head left) to confirm safety. Then honk, release the parking brake, start smoothly, and turn off the turn signal. 3. Right turn at an intersection: Upon hearing "Right turn ahead," turn on the right turn signal (for more than 3 seconds) and follow the guiding arrow to turn right into the driving lane. 4. U-turn: Upon hearing "U-turn ahead," turn on the left turn signal (for more than 3 seconds), observe the left rear traffic via the (left) rearview mirror, and confirm safety before reducing speed, shifting to a lower gear, and entering the U-turn zone. While entering, observe traffic conditions left and right, confirm safety, enter the new lane, proceed normally, and turn off the left turn signal. 5. Straight through an intersection: Upon hearing "Pass the intersection ahead," slow down (brake), observe road traffic, and proceed according to traffic signals. Speed should be below 30km/h, and stopping within the intersection is prohibited. 6. Left turn at an intersection: Upon hearing "Left turn ahead," turn on the left turn signal (for more than 3 seconds) and follow the guiding arrow to turn left into the driving lane. 7. Passing a bus stop: Upon hearing "Pass the bus stop," slow down (brake) or keep speed below 30km/h before entering the area. Observe left and right (turning head) to yield to buses and pedestrians, and proceed after confirming safety. 8. Gear shifting: Upon hearing "Please perform gear shifting," shift to 2nd gear, then sequentially upshift to 5th gear (exceeding 40km/h in 5th), then downshift back to 2nd. 9. Straight driving: Upon hearing "Maintain straight driving," look ahead, hold the steering wheel with both hands, and keep the vehicle straight. Do not cross lane dividers. 10. Lane change: Upon hearing "Change lanes," turn on the (left) turn signal (for more than 3 seconds), observe rear traffic via the (left) rearview mirror (turning head left), and confirm safety before turning (left) to change lanes. If conditions are not met, slow down and wait. Do not change two lanes consecutively. 11. Passing a crosswalk: Upon hearing "Crosswalk ahead," slow down (brake) or keep speed below 30km/h before entering. If pedestrians are crossing, stop outside the safety line and proceed only after they have crossed. 12. Passing a school zone: Upon hearing "School zone ahead," slow down (brake) or keep speed below 30km/h before entering. Observe left and right (turning head) to yield to students, and proceed after confirming safety. 13. Pulling over: Upon hearing "Please pull over," turn on the right turn signal (for more than 3 seconds), observe right rear traffic via the (right) rearview mirror, and confirm safety before parking parallel to the curb (or road edge solid line) within 30cm without touching it. Stop the vehicle, engage the parking brake, and shift to neutral.
Was this review help?
4
5
Share
More Forum Discussions

What does China's new license plate look like?

The new license plate features separators in three colors: blue, yellow, and red. The left two characters represent information like "Yue A," while the right side has been expanded from the previous five digits to six digits, similar to the current new energy vehicle license plates. Here is some relevant information about license plates: Introduction: License plates, commonly known as vehicle plates, refer to the plates mounted on the front and rear of a vehicle. Additional Information: They are typically made of aluminum, sheet metal, plastic, or paper, and display the vehicle's registration number, registration region, or other relevant details. License plates serve as a unique identifier and registration record for each vehicle. Their primary function is to indicate the vehicle's region of registration and allow for tracking of the vehicle's owner and registration details based on the plate number.
2
4
Share

What brand are the tires on the CT6?

Cadillac CT6 offers two specifications of tires across its entire lineup: Goodyear Assurance ComfortTred 235/50R18 and Goodyear Eagle F1 245/45R19. The spare tire for the CT6 is a non-full-size Maxxis tire with the specification T135/70R18. Below is a tutorial for replacing tires on the Cadillac CT6: 1. First, park the vehicle on a level surface. If on the road, place a safety warning sign behind the vehicle. Use tools to remove the tire nuts, loosening them in a diagonal sequence. 2. Position the jack directly beneath the support point, then slowly adjust the jack to lift the chassis. Once the tire is off the ground, it can be removed. Due to tight fit, the tire might be difficult to remove; a gentle kick with your foot can help. 3. Place the new tire and manually secure the nuts. Finally, install the bolts diagonally. Do not apply excessive force when tightening the nuts; the final tightening should be done once the wheel touches the ground.
9
0
Share

What is the initial stopping point for reverse parking?

The initial stopping point for reverse parking is the point where you fully turn the steering wheel. Below are the precautions for reverse parking. Introduction to reversing direction: When reversing, the direction in which you turn the steering wheel determines the direction the rear of the car moves. Turning the steering wheel to the right will make the rear of the car move to the right. Whether reversing or driving normally, the movement direction of the car body is consistent with the direction of the steering wheel. When reversing, turning the steering wheel to the left will make the rear of the car move to the left, and turning it to the right will make the rear move to the right. When correcting, if the rear of the car deviates to one side, the steering wheel should be turned in the opposite direction. For example, if the car body leans to the left, you need to turn the steering wheel to the right to straighten it. Introduction to reverse correction methods: When reversing, look through the rearview mirror. If you feel the distance is wider on one side, turn the steering wheel towards that side. Therefore, if the right side is wider, turn the steering wheel to the right and observe the rearview mirror. When the car body needs to be corrected, return the steering wheel to the original position.
7
3
Share

What is PICC's damage assessment standard for waterlogged vehicles?

The following are PICC's damage assessment standards for waterlogged vehicles: Preparation before assessment: After receiving the claim report, the insurance company staff will review the survey records, understand the accident loss situation, and inquire about the surveyor's opinions. Then, they will check the insurance coverage of the vehicle to determine the corresponding insurance type and payment limit. It is important to carefully review the claim records of the involved vehicle to avoid duplicate compensation. Damage assessment approval: Before disassembling and inspecting the accident vehicle, if the estimated loss amount exceeds the branch's assessment authority, the assessor needs to fill out the "Major Case Damage Assessment Report" and submit it to the provincial company for approval and authorization before proceeding with the assessment. Basic principles of vehicle loss: The repair scope of the vehicle is limited to the damage caused by this accident; repairable parts should be repaired as much as possible; areas that can be partially repaired should not be expanded to overall repairs; replaceable parts should not be replaced with assemblies; labor costs and spare parts prices should be accurately determined based on the difficulty of the repair process and the local labor cost level.
5
5
Share

What is the reason for the humming sound when accelerating in fourth gear of Wuling Zhiguang?

The reasons for the humming sound when accelerating in fourth gear of Wuling Zhiguang are as follows: 1. Engine fuel pump malfunction: Damage to the engine fuel pump results in insufficient fuel supply. Even if the driver floors the accelerator, causing the engine speed to increase, the fuel injection volume remains low, leading to reduced engine output power and consequently weak acceleration. 2. Valve timing issue: Modern engines utilize CVVD valve timing systems to improve fuel efficiency. However, if the CVVD hydraulic control system is damaged, with oil leaks from sealing rings or malfunctioning CVVT, the engine's intake and exhaust will be affected, naturally reducing combustion efficiency and causing a drop in engine output torque.
20
1
Share

How to Remove the Magotan Window Regulator?

Magotan window regulator removal steps are as follows: 1. Prepare tools and remove the door assembly; 2. Roll the window up; 3. Unscrew the window regulator fixing screws, then remove the glass; 4. Disconnect the wiring, usually the connector is located on the inner side of the door; 5. After disconnecting the wires, the window regulator can be removed. More information about window regulators: The window regulator is the lifting device for car door/window glass, mainly divided into electric window regulators and manual window regulators. Modern car door/window glass generally adopts push-button electric lifting, i.e., using electric window regulators. Electric window regulators for cars mostly consist of motors, reducers, guide ropes, guide plates, glass mounting brackets, etc. The master switch is controlled by the driver to open/close all door/window glass, while sub-switches on each door handle allow passengers to control individual window glass, making operation very convenient. The most common window issue is hardened rubber strips in the glass track or dirt accumulation, causing sluggish or stuck window movement. Therefore, regularly spraying WD-40 in the window tracks for lubrication is crucial. For rubber strips, applying lubricant maintains flexibility and reduces cracking. Another common issue is long-term wear, such as motor failure or linkage mechanism rust/breakage due to water exposure, leading to window derailment. In such cases, factory replacement of parts is necessary.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.