Location of the BYD F0 Transmission?

What Causes Unstable Idle Speed at Startup?

The reasons for unstable idle speed after startup are: 1. Clogged idle air passage or malfunctioning idle control device; 2. Weak spark in individual cylinder spark plugs; 3. Poor sealing of individual valves or intake manifold leaks; 4. Incorrect ignition timing (too early or too late) or improper idle speed adjustment. Solutions: 1. When the engine idle is unstable, adjust the idle speed first. If the problem persists after adjustment, check whether the idle jet and idle air jet are clogged. If clogged, clean them with gasoline or acetone and blow through with compressed air; 2. If unstable idle is accompanied by reduced engine power, further inspect spark plug performance, valve sealing, and ignition timing. Repair or adjust as necessary.

18

2

Share

Why does the Mazda Atenza sway from side to side at low speeds?

The Mazda Atenza's swaying from side to side at low speeds is caused by incorrect wheel balance data. Below is a detailed introduction to the Mazda Atenza: 1. Configuration: The new vehicle comes standard with features such as an intelligent idle stop system and brake energy recovery system. The Mazda Atenza 2.5L model accelerates from 0 to 100 km/h in just 8.3 seconds, with a combined fuel consumption as low as 6.9 liters per 100 km, while the 2.0L model achieves a combined fuel consumption of only 6.3 liters per 100 km. 2. Exterior: The car adopts Mazda's KODO design philosophy, with a U-shaped front grille paired with LED headlights, enhancing its sporty appearance. The new model introduces an 11-speaker sound system. Compared to the previous generation Mazda6, the Atenza's wheelbase has been increased by 111mm, providing more spacious rear seating. The Atenza utilizes the Skyactiv chassis technology, equipped with a high-performance MacPherson strut front suspension and a multi-link independent rear suspension. Through structural optimization, it achieves both weight reduction and increased rigidity.

3

5

Share

What procedures are required to change a seven-seater to a four-seater?

Procedures for applying to change a seven-seater vehicle to a four-seater: You need to apply at the local vehicle registration office. Only after the application is approved can you drive on the road. If the application is not submitted, the vehicle will not pass the annual inspection. According to the relevant regulations of the traffic management department of the public security authority, the following actions require an application: 1. Changing the body color or replacing the engine, or altering the vehicle body or frame; 2. Changing the use nature of the vehicle, such as converting from a commercial motor vehicle to a non-commercial motor vehicle or vice versa. The application procedures are as follows: 1. The vehicle owner must submit an application to the local vehicle registration office; 2. An application for change registration must be submitted to the vehicle registration office within the specified time after the modification; 3. Before registration, the vehicle design drawings must be submitted, and any traffic safety violations or accidents must be resolved; 4. Failure to apply for the change may result in warnings or fines from the public security traffic management department.

20

1

Share

What are the benefits of having wider rear wheels than front wheels?

The benefits of having wider rear wheels than front wheels include reducing power loss, improving vehicle handling during turns, and enhancing visual appeal. Below is a detailed introduction to the advantages of wider rear wheels: 1. Reducing power loss. The primary purpose is to minimize power loss. Since rear-wheel-drive vehicles primarily transmit power through the rear wheels, wider tires increase the contact area with the ground, thereby providing greater traction. This prevents wheel spin during acceleration, which would otherwise lead to power loss. 2. Improving handling during cornering. A larger contact area with the ground enhances the vehicle's handling in corners. For example, during emergency braking, the additional tread grooves act like powerful suction cups, firmly gripping the ground and ensuring stability even on slippery surfaces. 3. Enhancing sporty visual appeal. Visually, wider tires are more appealing. With a lower aspect ratio, the rubber tread appears thinner while the wheel rims look larger, creating a more sporty visual effect.

8

4

Share

What Causes the Jerking During Low-Speed Gear Shifts in the Atenza?

The jerking during low-speed gear shifts in the Atenza is caused by clutch failure. Below is a detailed introduction to the Atenza:1. Configuration: The new vehicle comes standard with features such as the Smart Idling Stop System and Brake Energy Regeneration System. The Atenza 2.5L model accelerates from 0 to 100 km/h in just 8.3 seconds, with a combined fuel consumption as low as 6.9 liters per 100 km, while the 2.0L model achieves a combined fuel consumption of only 6.3 liters per 100 km.2. Exterior Design: The car adopts Mazda's KODO design philosophy, featuring a U-shaped front grille paired with LED headlights for a more sporty appearance. The new model introduces an 11-speaker sound system. Compared to the previous-generation Mazda6, the Atenza's wheelbase has been increased by 112 mm, providing more spacious rear seating. The Atenza utilizes the SKYACTIV-Chassis technology, equipped with a high-performance MacPherson strut front suspension and a multi-link independent rear suspension. Through structural optimization, it achieves both weight reduction and increased rigidity.

12

3

Share

What are the reasons for the excessive motor temperature in the BAIC EX360?

Below are the reasons for the excessive motor temperature in the BAIC EX360: 1. Instantaneous voltage issue: When the motor's instantaneous voltage exceeds 10% above the rated voltage or falls below 5% of the rated voltage, it will cause the motor to heat up and experience a temperature rise under rated load. In such cases, the voltage should be checked and adjusted. 2. Power supply voltage issue: An imbalance in the three-phase power supply voltage of the motor can also cause the motor to overheat. This is because when the three-phase power supply voltage imbalance exceeds 5%, it leads to an imbalance in the three-phase current. The solution is to check and adjust the voltage. 3. Switch and circuit issues: Contact problems in the motor's power switch or a blown fuse in one phase can result in single-phase operation, leading to an increase in motor temperature. The solution is to repair or replace the damaged components.

10

3

Share

Location of the BYD F0 Transmission?

What Causes Unstable Idle Speed at Startup?

Why does the Mazda Atenza sway from side to side at low speeds?

What procedures are required to change a seven-seater to a four-seater?

What are the benefits of having wider rear wheels than front wheels?

What Causes the Jerking During Low-Speed Gear Shifts in the Atenza?

What are the reasons for the excessive motor temperature in the BAIC EX360?

How Many Grams of Freon Should Be Added to the Baojun 560?

At what mileage does the Mazda6 Atenza become less enjoyable to drive?

Should the clutch be fully released after starting?

How many cylinders does the Mercedes-Benz C260L engine have?