Is Volkswagen a German Car?

Is the compulsory traffic insurance the same for large and small vehicles?

The compulsory traffic insurance coverage is the same for large and small vehicles, but the premiums are different. Introduction to compulsory traffic insurance: The full name of compulsory traffic insurance is "Compulsory Traffic Accident Liability Insurance for Motor Vehicles". It is a mandatory liability insurance where the insurance company compensates for personal injuries, deaths, and property losses (excluding the vehicle's occupants and the insured) caused by road traffic accidents involving the insured motor vehicle, within the liability limits. Coverage of compulsory traffic insurance: Compared to the more than 20 exemption clauses in commercial third-party liability insurance, the exemptions for compulsory traffic insurance are limited to "losses caused intentionally by the victim", "property losses of the insured themselves", "related arbitration and litigation costs", and certain indirect losses caused by the accident, offering much broader coverage. Moreover, regardless of whether the insured vehicle is at fault in the accident, compulsory traffic insurance provides compensation within the liability limits, with no deductible or exemption rate.

19

4

Share

Is a small car inspected every two years?

Small cars within ten years are inspected every two years. Inspection regulations: Small cars within ten years are inspected every two years. For new cars within 6 years, an inspection mark needs to be applied for every two years, but the vehicle does not need to undergo on-site testing. At the 6th and 8th years, the vehicle must undergo on-site testing. For private cars over 10 years old, the original inspection cycle still applies, i.e., annual inspection for cars aged 10 to 15 years, and semi-annual inspection for cars over 15 years. Inspection precautions: During the inspection, the staff at the vehicle management office will check the vehicle's frame number, engine number, and chassis. Cleaning the vehicle's body, engine compartment, and chassis in advance can facilitate the inspection process and help pass the inspection. During the inspection, the vehicle owner can apply for the inspection compliance mark at the local vehicle management office within 3 months before the expiration of the vehicle's inspection validity period.

20

2

Share

Where to Check the Vehicle Production Date?

Below the B-pillar on the passenger side, the certificate of conformity that comes with the new vehicle. Specific locations: Below the B-pillar on the passenger side, open the door to see it. This nameplate only shows the year and month. The nameplate also notes the vehicle's VIN; the certificate of conformity that comes with the new vehicle is located in the upper right corner of the certificate. The production date marked here can be precise to the year, month, and day. Details about the nameplate date: Not applicable to all vehicle models. When a new vehicle is delivered to the dealership, there will be a paper nameplate on the front windshield near the driver's seat. The paper nameplate shows the VIN and the MIIT fuel consumption. If the bottom of the paper nameplate specifies the year, month, and day, then the production date on this nameplate can be used as a reference date. If the nameplate only shows the year and month, it cannot be considered as the production date.

14

3

Share

What does oil churning loss mean?

Oil churning loss refers to the power loss due to oil churning, also known as no-load loss or idle power loss. The extent of oil churning loss varies depending on the lubrication method, and within different lubrication methods, it also differs due to various factors. Impact of oil temperature on churning loss: Before significant changes in lubricant viscosity occur, oil temperature has the greatest influence on transmission oil churning power loss, followed by rotational speed, with oil volume having a relatively minor effect. When oil volume is constant, at low speeds (below 1000 rpm), power loss shows a linear relationship with both oil temperature and rotational speed, and the power loss is relatively small. At high speeds, the power loss does not exhibit a linear relationship with oil temperature and rotational speed. Impact of oil volume on churning loss: When lubricant temperature is constant, at low speeds (below 1000 rpm), power loss has a linear relationship with oil volume. At high speeds, this relationship is not linear. With constant lubricant temperature, power loss generally shows a linear relationship with rotational speed (though when the transmission is in neutral, the best-fit curve is not a simple linear one).

18

1

Share

What is the yellow wire in a motorcycle?

The yellow wire is responsible for the generator lighting and charging power output. Principle: The yellow wire and the white wire from the magneto coil are both output wires from the lighting and charging coil. They are connected to the rectifier for voltage regulation, lighting, and charging the battery. For motorcycles with AC headlights, the yellow wire splits into two paths: one goes to the voltage regulator for stabilization, and the other connects to the headlight switch to supply power for the headlight. The white wire connects to the rectifier to charge the battery. For motorcycles with DC lighting, both the yellow and white wires connect to the rectifier, and the stabilized current is used to charge the battery. The headlight power is then supplied by the battery. Functions of other wires: Red - Battery positive terminal to the ignition switch front; Pink - Engine power output; Blue - Headlight high beam; Green - Power negative and ground wire; Black - Ignition switch to the vehicle's power positive terminal; White - Generator charging output, headlight low beam; Gray - Flasher to the turn signal switch.

14

3

Share

What lights should be used when driving in the same direction at night?

When driving behind another vehicle at night, use low beam headlights. Here are the specific instructions for using low beam headlights: 1. Following another vehicle: When driving behind another vehicle at night, turn off the high beam headlights and turn on the low beam headlights. If high beams are used, the driver in front will not be able to observe the situation behind through the rearview and side mirrors. 2. Meeting oncoming traffic or at intersections: When meeting oncoming traffic or when there is an approaching vehicle, turn off the high beams. High beams can make it difficult for the oncoming driver to see the road ahead, which can easily lead to accidents. If the oncoming vehicle does not turn off its high beams, you can alternately switch between high and low beams to signal them to turn off the high beams. When passing through a dimly lit intersection, alternately switch between high and low beams and honk the horn. 3. Overtaking: When preparing to overtake, first alternately switch between high and low beams and honk the horn to alert the vehicle in front of your intention to overtake. Then, turn on the left turn signal, check the situation behind you, and if there is no oncoming traffic, change lanes to the left, accelerate, and overtake.

19

5

Share

Is Volkswagen a German Car?

Is the compulsory traffic insurance the same for large and small vehicles?

Is a small car inspected every two years?

Where to Check the Vehicle Production Date?

What does oil churning loss mean?

What is the yellow wire in a motorcycle?

What lights should be used when driving in the same direction at night?

Should You Downshift or Upshift When Going Uphill?

What does a warning light with a circle and six dots indicate?

Can motorcycles share the same lane with cars?

Why is throttle body cleaning so expensive at 4S stores?