Is There Any Danger When the Airbag Deploys While Wearing Glasses?

What is the speed limit on the acceleration lane?

There is no minimum speed limit for the acceleration lane. Below is relevant information about acceleration lanes: 1. Introduction: An acceleration lane is a dedicated lane provided for vehicles to accelerate before merging into high-speed traffic flow. It is generally the rightmost section of road after exiting a ramp, marked with dashed lines on the ground. After accelerating, vehicles can enter the main traffic lane. The length of acceleration lanes is not fixed and needs to be calculated based on current road traffic volume and speed limits to determine an appropriate acceleration distance. 2. Requirements: After passing through a ramp exit, vehicles must first enter the acceleration lane and reach the specified speed before merging into the main traffic lane. Direct entry from the ramp exit to the main lane is prohibited and may result in penalty points.

3

1

Share

What are the three electric components of new energy vehicles?

New energy vehicles' three electric components refer to the battery, electric drive, and electric control. More information about new energy vehicles is as follows: 1. New energy vehicles refer to vehicles that use unconventional vehicle fuels as power sources (or use conventional vehicle fuels with new types of on-board power devices), integrating advanced technologies in vehicle power control and driving, resulting in vehicles with advanced technical principles, new technologies, and new structures. 2. New energy vehicles include four major types: hybrid electric vehicles, pure electric vehicles, fuel cell electric vehicles, and other new energy vehicles.

13

2

Share

How to Use Toyota HOLD?

Toyota HOLD is primarily used as follows: 1. Press the Hold button after starting the vehicle. 2. A green Hold light will illuminate on the dashboard. 3. When stopping at a traffic light by pressing the brake pedal, the Hold indicator on the dashboard will turn orange, indicating the vehicle is stationary. When the light turns green, simply press the accelerator to proceed. Additional information: 1. After the engine comes to a stop with HOLD activated, the vehicle will shut off. Pressing the accelerator to start will restart the engine, and HOLD will automatically deactivate. 2. HOLD is the autohold button, with EV (Electric Vehicle) mode located next to it. EV mode can only be selected when the battery meets certain charge conditions. P stands for the electronic parking brake button.

2

5

Share

Effects of Too Rich or Too Lean Air-Fuel Mixture on Motorcycle Engines

1. When the air-fuel mixture is too rich, incomplete combustion occurs, generating large amounts of carbon monoxide and free carbon particles in the cylinder. This leads to carbon deposits on the cylinder head, piston crown, valves, and spark plugs, accompanied by blue smoke from the exhaust pipe and severe exhaust pollution. Moreover, the carbon monoxide in the exhaust gas may reignite in the exhaust pipe due to high-temperature exhaust gases, causing "backfiring" in the exhaust system. Additionally, the combustion speed of such a mixture is relatively low, resulting in reduced effective power and significantly increased fuel consumption. Furthermore, an overly rich mixture can wash away and damage the lubricating oil film in the cylinder, compromising the lubrication performance of friction components. A rich mixture also significantly impacts the engine's idle performance, manifesting as extremely unstable idle speed, severe cases of no idle, and ultimately causing the engine to stall. In such cases, removing the spark plug will reveal blackened electrodes, confirming an overly rich air-fuel mixture. 2. When the air-fuel mixture is too lean, the combustion speed of the fuel decreases. Some of the mixture may continue burning as the piston moves toward bottom dead center (in four-stroke engines, where the combustion chamber volume gradually increases). In severe cases, the combustion process may even extend into the intake stroke of the next cycle, causing residual flames in the cylinder to ignite the mixture in the intake pipe and carburetor outlet chamber through the open intake valve. This results in backfiring (also known as carburetor backfire) and produces knocking noises. This partial combustion not only converts less heat into mechanical work but also increases heat loss through the cylinder wall to the cooling water or radiator fins. Consequently, an overly lean mixture causes engine overheating and reduced power output. A lean mixture also leads to higher idle speeds, making it difficult for the engine speed to drop to idle quickly when decelerating. In such cases, removing the spark plug will show white electrodes, confirming an overly lean air-fuel mixture.

11

0

Share

What Causes the Car Body to Shake During Gear Shifting?

There are two main reasons for the shaking: one is releasing the clutch too quickly; the other is driving at too high a speed, which means the gear and speed are mismatched. Below are the reasons for car shaking during gear shifting: 1. Jerking refers to a slight and brief shaking phenomenon that occurs when the transmission shifts gears. Slow-motion videos show: at the moment the car's transmission shifts from 1st to 2nd gear, there is a slight and brief shake; 2. All AT transmissions will have jerking, the difference lies only in the degree and duration of the transmission's shaking during the gear shift. If the degree is small and the duration is short, it is not easily noticeable; 3. However, if the degree is large and the duration is long, it will be clearly noticeable. This is commonly referred to as 'experiencing jerking while driving,' which can make people feel uncomfortable, affect the driving rhythm, and lead to a poorer driving experience.

6

2

Share

What is the reason for the fuel gauge remaining in its previous state after refueling?

It is recommended to drive a certain distance after refueling to test. If the fuel gauge still shows the previous state, then there may be a fault with the fuel level sensor, and further inspection and repair at a repair shop are required. Below is relevant information about the car fuel gauge: 1. Introduction: The car fuel gauge is designed based on principles of physical mechanics and electricity. From a mechanical perspective, the fuel level scale position in the fuel tank is determined using the theoretical knowledge of buoyancy (somewhat similar to the water tank in a household toilet). This value is then transmitted to a rheostat via a sensor, and different voltage values are obtained by sliding on the rheostat, which are then converted into the scale on the fuel gauge, i.e., the fuel gauge you see. 2. Types: There are two types of fuel gauges in use in vehicles, the pointer type and the digital type.

17

3

Share

Is There Any Danger When the Airbag Deploys While Wearing Glasses?

What is the speed limit on the acceleration lane?

What are the three electric components of new energy vehicles?

How to Use Toyota HOLD?

Effects of Too Rich or Too Lean Air-Fuel Mixture on Motorcycle Engines

What Causes the Car Body to Shake During Gear Shifting?

What is the reason for the fuel gauge remaining in its previous state after refueling?

Should the clutch be released quickly when shifting gears?

Must Gear Shifting Be Completed Within 100 Meters?

What Causes the Fuel Gauge Needle to Stay at Full After Refueling?

What is the gear shifting rhyme?