···
Log in / Register

Is there a venue fee for the make-up test of Subject 2?

1 Answers
DeVera
08/27/25 2:41am

Some places require it, depending on the local regulations. Below is relevant information about Subject 2: 1. Overview: Subject 2, also known as the small road test, is part of the motor vehicle driver's license examination. It refers to the field driving skills test. For small vehicles (C1 and C2), the test items include five mandatory components: reverse parking, parallel parking, stopping and starting on a slope, right-angle turns, and curve driving (commonly known as the S-curve). Some regions also include a sixth item: high-speed toll card collection. 2. Teaching aids: Teaching software: Students can use driver simulation test software on mobile or computer devices to study traffic regulations. Teaching materials: "Safe Driving Starts Here," compiled by the Ministry of Transport of the People's Republic of China. Driving schools may provide learning materials uniformly, or students may purchase them at their own expense.

Was this review help?
10
2
Share
More Forum Discussions

What is the normal sound of engine idling?

Normally, during the engine startup process, there should be no screeching sounds, and the engine idling sound should be even. When starting a cold engine, there might be a ticking sound, which weakens and disappears after the engine warms up. This is considered normal engine sound. The reasons for an increase in car engine noise are as follows: 1. Engine abnormal noise: The engine makes a tapping sound, similar to a pencil knocking on a table, and the sound increases as the engine speed increases. Possible causes include impurities inside the engine. It is recommended to change the engine oil, oil filter, and clean the engine. 2. Inability to increase speed: While driving, acceleration may be normal, and ignition might also be normal. However, if you notice that the engine speed is too high but the speed still doesn't increase when driving at a constant speed, try checking the coolant. If the oil pressure is too high or too low, check the oil pressure gauge. There might also be an issue with the ignition timing settings, which could lead to such symptoms. Other possible causes include internal engine problems, such as a clogged EGR valve.
8
1
Share

Is Sinochem Petroleum More Fuel-Efficient?

Domestic use of 90, 93, and 97 octane gasoline has been discontinued, with all currently used fuels meeting the National V standard, such as 92 and 95 octane gasoline. As these are upgraded National V fuel products, the gasoline density of both companies has become smaller, thus there is no claim of being more fuel-efficient. Below is additional information: 1. Sinochem Petroleum: Sinochem Petroleum Co., Ltd. was established on May 21, 1988, as a wholly-owned subsidiary of Sinochem Group, primarily engaged in the import and export of crude oil and refined oil products. It is the professional company of Sinochem in domestic petroleum trade. 2. Company Business: The company's operations mainly focus on crude oil trade and refined oil trade and distribution. The main products include crude oil, fuel oil, gasoline, diesel, aviation kerosene, liquefied petroleum gas, etc. The primary business methods encompass import and export, international entrepot trade, processing trade, paper trading, and domestic distribution.
10
3
Share

What Does Coating Car Wash Mean?

Coating beauty car wash combines the simplest car washing method with the optimal car beauty treatment—coating, enhancing the functionality of car washing while completing vehicle beauty maintenance. This means applying a layer of glass fiber coating to the car paint surface immediately after washing, which is quick and convenient. In just a few minutes, the vehicle can be thoroughly protected, preventing paint oxidation, acid rain corrosion, UV damage, and increasing paint hardness by three times. Additional information: The following are the specific details of coating car wash: 1. Coating beauty car wash is the latest product combining car washing technology and market demand. 2. Coating beauty car wash democratizes the existing high-end glass fiber coating, making car paint coating a daily car care routine. Coating beauty car wash provides the maintenance benefits of car wax but without the damaging effects of wax on car paint.
4
3
Share

What does the semicircle exclamation mark warning light mean?

The semicircle exclamation mark warning light is the tire pressure warning light of the vehicle. Here are the specific details: 1. Tire pressure: The standard tire pressure is 2.4-2.5 bar. 2. Overinflation: If the tire pressure is too high, the contact area between the tire and the ground decreases, leading to increased pressure and wear per unit area, which can easily cause loss of braking control, tire blowouts when encountering road protrusions or depressions, damage to the vehicle's suspension system, and discomfort during rides. 3. Underinflation: This increases the contact area between the tire and the ground, causing abnormal temperature rise inside the tire while driving. Additionally, severe deformation of the tire sidewall accelerates aging of the internal steel wires and fabric layers, increasing the risk of blowouts, higher fuel consumption, and reduced tire lifespan.
15
3
Share

What Causes Engine Power Loss After Overheating?

Causes of engine power loss after overheating: 1. Electrical faults: The electric cooling fan fails to operate, reducing the radiator's heat dissipation capacity. When the air conditioning is not in use, the water temperature remains normal; however, when the air conditioning is activated, the water temperature rises significantly. This issue is typically caused by the electric fan of the air conditioning radiator not working or relay failure/damage. 2. Mechanical faults: The fan coupling lacks oil, is damaged, or stuck, preventing the cooling fan from operating. During prolonged engine operation, the water temperature becomes excessively high or even boils. This is usually due to a faulty thermostat obstructing water circulation. When the water temperature rises, the thermostat valve fails to open, preventing the coolant from entering the major circulation cycle, thus failing to dissipate heat or regulate water temperature. In tropical regions of southern China or during emergencies, the thermostat valve can be removed. Loose water pump belts or a damaged water pump can lead to a lack of circulating water. Leaks in hoses, water jackets, or the junctions between the cylinder block and cylinder head. 3. Improper assembly: For engines that have undergone major repairs or are newly assembled, incorrect dimensions or fitting clearances during installation often result in elevated water temperatures. A newly overhauled engine running at medium speed for about half an hour may exhibit high water temperatures, typically due to excessively small gaps between the pistons or piston rings and the cylinder walls. Prolonged operation under these conditions can cause ring sticking, ring breakage, or cylinder scoring. Debris left during repairs or improperly placed objects can block water passages, leading to high water temperatures. Blocked air intakes can also impair heat dissipation. 4. Improper adjustments: Excessive exhaust valve clearance. This delays the opening time of the exhaust valve and shortens its duration, resulting in poor exhaust flow and elevated water temperatures. This condition can usually be identified by a tapping sound between the valve and rocker arm during engine operation. Incorrect ignition timing. If ignition occurs too early, incomplete combustion can cause knocking and secondary ignition, raising the water temperature. If ignition occurs too late, incomplete combustion will similarly increase the water temperature.
6
5
Share

What Causes the OBD Engine Malfunction Light?

The engine malfunction light may illuminate due to the following 7 primary reasons: Sensor failure: This includes sensors such as coolant temperature, crankshaft position, air flow, intake temperature, and oxygen sensors. When these sensors are damaged, have poor connections, or experience signal interruptions, the vehicle's ECU cannot accurately obtain engine data, triggering the malfunction light. Fuel/oil quality issues: Failure to use the manufacturer-recommended fuel or engine oil may cause engine wear, leading to the malfunction light activation. Poor fuel mixture combustion: Incomplete combustion can cause engine carbon buildup or knocking. When detected by oxygen sensors and reported to the ECU, the malfunction light will illuminate as a warning. Contributing factors include spark plug failure, ignition coil issues, fuel pump malfunction, or fuel line blockage. Turbocharger problems: Issues with the intake boost system or turbocharger can trigger the light. Common turbocharger failures may be accompanied by oil leaks, excessive oil consumption, power loss, metallic noises, or blue/black exhaust smoke. Air intake issues: Obstructed engine air intake passages, often caused by dirty air filters that haven't been regularly cleaned, may eventually activate the malfunction light. Exhaust system faults: Problems like rear oxygen sensor failure, catalytic converter issues (most common), or exhaust camshaft/bearing failures can trigger the light. Leaded gasoline, improper lubricant additives, physical damage to the catalytic converter, or fuel system malfunctions often cause catalytic converter problems. Anti-theft system malfunction: If the electronic anti-theft system fails or isn't properly synchronized with the engine control unit, it may prevent normal engine operation while activating the warning light. When the engine light illuminates, follow these steps: 1. First check if the engine operates normally. If there's shaking, black smoke, or other abnormalities (especially with a red warning light), do not restart the engine. 2. If restarting is possible, wait 5-10 minutes after turning off the engine. Without pressing the brake pedal, press the start button once or turn the key halfway to the ON position (without depressing the clutch). The vehicle will perform a self-check for 5-10 seconds - observe if the warning light turns off. 3. If the light remains on, visit a service center immediately. Technicians can use diagnostic tools to read trouble codes and perform targeted repairs.
19
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.