Is there a toll for entering the highway on September 30th and exiting on October 1st?

2 Answers
AryaMarie
07/25/25 2:23pm
There is no toll for entering the highway on September 30th and exiting on October 1st. However, if you enter the highway before the free period starts and exit the province before the free time begins, you will be charged for the section of the highway when passing through the provincial boundary toll station. It is recommended to rest at a nearby service area before exiting the province and wait until the free time begins to pass through the provincial boundary toll station, so you won't have to pay the toll. If you enter the highway during the free period and exit during the toll period, you will be charged. If you can't exit the highway before 24:00 on the last day of the free period, you can exit at the nearest toll station just before the toll time starts, and the highway section above will be free.
Was this review help?
18
4
Share
MichaelLee
08/11/25 9:04pm
Having driven on highways for so many years, I'm quite familiar with the free policy during the National Day holiday. Usually, the free period starts at midnight on October 1st. No matter when you enter the highway, as long as you exit on October 1st, the toll station won't charge you. I often drive out for trips, and in your case, entering on September 30th and exiting on October 1st, the free toll is guaranteed. However, local rules might have minor adjustments, so checking a traffic app before departure is more reassuring. During the holiday, highway traffic is heavy, and exits can get congested, so it's best to plan your trip to avoid peak hours. Don't forget to check your vehicle—things like tire pressure and engine oil should be in good condition to avoid breakdowns. Safe driving is always the top priority; don't speed to save time, and leave some buffer for complex road conditions.
Was this review help?
20
4
Share
Expand All
More Forum Discussions

How to Remove the Spare Tire of a Highlander?

Open the rear door of the Highlander, then lift the outer floor panel of the trunk. On the right side of the vehicle, you will find a small square cover approximately 7-8cm in size. Remove this cover to reveal a screw head. Use the provided tool to loosen this screw and take out the spare tire. Below are the steps for replacing the spare tire: 1. Prepare a jack, wrench, and the spare tire for replacement. 2. Use the jack to lift the vehicle and remove the tire bolts with the wrench. 3. Once all bolts are removed, take off the tire and install the spare tire. 4. Tighten all the bolts back in place and then remove the jack.
12
4
Share

How to Distinguish Between the 8th and 8.5th Generation Accord?

The differences between the 8th and 8.5th generation Accord are that the 8.5th generation has more configurations and interior design upgrades compared to the 8th generation, while other basic configurations remain the same. The dimensions of the 8th generation Accord are 4945mm in length, 1845mm in width, and 1480mm in height. Below is relevant information about the two: The production years of the 8th generation Accord and the 8.5th generation Accord differ. The 8th generation Accord was produced from 2008 to 2010, while the 8.5th generation Accord was produced from 2011 to 2013. The 8th generation Accord is equipped with a 2.0L i-VTEC engine, whereas the 8.5th generation Accord comes with two engine options: a 2.4L i-VTEC engine and a 2.0L i-VTEC engine. The 8th generation Accord features a two-row hollow grille design under the front emblem, while the 8.5th generation Accord has a two-column hollow design under the front emblem.
10
1
Share

What is the minimum ground clearance of the Tiguan?

The minimum ground clearance of the Tiguan front-wheel-drive version is 160mm, while the all-wheel-drive version has a minimum ground clearance of 180mm. The unladen ground clearance is 210mm. Below is additional information about the Tiguan: 1. The Tiguan is equipped with industry-leading 1.8TSI and 2.0TSI engines, which are powerful and fuel-efficient, featuring high-pressure direct injection technology. 2. The 2.0TSI engine delivers a maximum power output of 147kW and a maximum torque of 280Nm, with strong turbocharged engine performance and excellent handling. 3. The exterior dimensions of the Tiguan are 4712mm in length, 1839mm in width, and 1673mm in height, with a wheelbase of 2791mm.
10
1
Share

What is the maintenance interval for the Audi A3?

Audi A3's maintenance interval is: 6 months/5,000KM. At 3,000KM, a maintenance reminder will display upon each engine start and shutdown. Below are the Audi A3 maintenance items: 1. Replacement of engine oil, oil filter, air filter, fuel filter, cabin air filter, brake fluid, and spark plugs. Coolant is replaced as needed. 2. Perform engine cleaning every 20,000-30,000KM, including intake tract, throttle body, fuel injectors, fuel lines, and engine computer inspection and calibration. 3. The Audi A3 maintenance cycle is calculated from the date of vehicle purchase invoice. The three-guarantee validity period is 2 years or 50,000KM, while the warranty period is 3 years or 100,000KM, whichever comes first.
2
0
Share

Where is the cabin air filter located in a BMW 1 Series?

The cabin air filter in the BMW 1 Series is located behind the glove compartment on the passenger side. To replace the cabin air filter, you need to remove the passenger side glove compartment first. The BMW 1 Series is a compact car under the BMW brand. Here are the specifications of the BMW 1 Series: The domestic version has a wheelbase of 2670mm, with length, width and height of 4456mm, 1803mm, and 1446mm respectively. The BMW 1 Series is equipped with two engines: a 1.5-liter turbocharged three-cylinder engine and a 2.0-liter turbocharged four-cylinder engine. The 1.5-liter turbocharged engine delivers 140 horsepower and 220 Nm of maximum torque, with a maximum power output at 4600-6500 rpm and peak torque available between 1480-4200 rpm. The 2.0-liter turbocharged engine produces 192 horsepower and 280 Nm of maximum torque, achieving maximum power at 5000-6000 rpm and peak torque between 1350-4600 rpm.
19
4
Share

What is the engine model of the Tiggo 8?

The engine model of the Tiggo 8 is SQRE4T15B. The 1.5T low-power version has a maximum power of 108kW and a maximum torque of 210Nm, the 1.5T high-power version has a maximum power of 115kW and a maximum torque of 230Nm, and the 1.6T version has a maximum power of 145kW and a maximum torque of 290Nm. The engine of the Tiggo 8 was jointly developed by Chery and AVL, but it is produced in Chery's engine production base in China, so this engine is a domestic engine. For daily maintenance of the Tiggo 8's engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected based on mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance will deteriorate, causing various problems for the engine. To avoid faults, the oil should be changed regularly according to usage conditions, and the oil level should be kept moderate. When the oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and the oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing the oil to bypass through the bypass valve and bring contaminants back to the lubrication parts, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gas, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from part wear to form sludge. A small amount of sludge remains suspended in the oil, while a large amount precipitates, blocking the filter and oil holes, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the normal operation of the engine but also extends the overall lifespan of the radiator and engine.
1
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.