···
Log in / Register

Is There a Retake Opportunity for Subject 2?

1 Answers
DeAlessandra
09/09/25 3:20am

Each successful appointment for the motor vehicle driver's license application comes with a second chance for the exam. Below is the relevant information: Active Application: If the first exam attempt is unsuccessful, the applicant can immediately retake it once. According to Article 37 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses," each subject exam can be taken once, and if failed, it can be retaken once. Rescheduling: If the applicant does not participate in the retake or fails the retake, the current exam session ends, and the applicant must reschedule the exam. However, for Subject 2 and Subject 3 exams, rescheduling must be done at least ten days later. If the Subject 3 safety and civilized driving knowledge exam is failed, the previously passed road driving skills exam results remain valid. Within the validity period of the driving skills test permit, the number of rescheduled exams for Subject 2 and Subject 3 road driving skills exams must not exceed five times. If the fifth rescheduled exam is still unsuccessful, the results of other previously passed subjects will be invalidated.

Was this review help?
2
2
Share
More Forum Discussions

How to Remove the Cabin Air Filter of Buick Envision?

Buick Envision's cabin air filter is located under the front passenger seat, near the left foot position, towards the inner side. Use a flathead screwdriver to firmly push and pull it outward. Insert your fingers inside and forcefully pull out the old cabin air filter. Start by pulling out one corner first, then gradually remove each corner one by one, as the filter is larger than the opening. Below is relevant information about the cabin air filter: 1. The Buick Envision cabin air filter serves the following purposes: separating solid impurities such as pollen and PM2.5 from the air; adsorbing moisture, carbon dioxide, vehicle exhaust, odors, and ensuring clean cabin air without bacterial growth. 2. The recommended maintenance interval for the vehicle's cabin air filter is approximately 10,000 kilometers or every six months. However, if driving frequently in severe smog conditions, it's advisable to replace it every three months. After replacing the cabin air filter, the PM2.5 reading can drop below 20 whether using external or internal air circulation.
10
4
Share

Can I pick up the ordered car later?

You can pick up the ordered car later. Here are some relevant considerations when ordering a car: 1. Model and Price: Before placing an order, you can research the model online, including basic configuration differences and price discounts. After gaining a preliminary understanding of the model and discount range, you can negotiate with sales consultants at 4S stores. It is recommended to compare offers from multiple dealers. 2. Vehicle Information: Before ordering, confirm the model, chassis number, engine number, and color of the car you intend to purchase. Especially ensure that both the car code and identification number are clearly stated to avoid any issues when picking up the car. 3. Order Contract: Before signing the contract, finalize the price and any included gifts. Pay attention to the type of order when drafting the contract. Additionally, clearly specify the costs for insurance and purchase tax, as well as the deposit and pickup time. Clearly define liability for breaches to prevent future disputes. Regarding the deposit, try to pay as little as possible. After drafting the contract, carefully review it to avoid any omissions. Finally, sign the contract and provide your contact information to complete the order process.
14
3
Share

Will 4S stores sell flooded cars as new cars?

4S stores generally do not sell flooded cars as new cars. Key points for restoring flooded vehicles are as follows: 1. External cleaning: After the vehicle is towed away from the flooded area, the exterior should be cleaned first, such as the inner side of the front and rear bumpers, the left and right rearview mirrors and their internal motors, and removable rearview mirror lenses should be disassembled and cleaned. 2. Internal cleaning: After initial cleaning, remove and clean the seats, electrical components (computers, audio systems, relays, dashboards), door panels, headliners, interior panels, light assemblies, door waterproof liners, sunroof assemblies, etc. 3. Engine compartment cleaning: Remove and clean the engine hood insulation panel, disconnect the battery, remove the timing belt cover to clean the inside to prevent poor crankshaft position sensor response, clean the generator interior with high-pressure water, clean the radiator and cooling fins to prevent overheating and poor cooling, and ensure every electrical connector is thoroughly cleaned.
11
5
Share

What Do the Two Numbers in Tire Pressure Display Represent?

The two numbers in the tire pressure display represent the minimum and maximum values of the tire pressure. This is because tire pressure is not fixed; it can fluctuate as the wheels rotate, and even when the vehicle is stationary, tire pressure can increase in hot weather. In other words, tire pressure can change. There are generally three reasons for abnormal tire pressure: Abnormal Tire Pressure: The system typically alerts when the pressure is below 1.8 bar or exceeds 3.0 bar. In such cases, tire inspection and pressure adjustment are necessary. Tire Pressure Monitoring Not Reset: After inflating the tires, if the tire pressure monitoring system is not reset in time, it will continue to display the previously recorded data, causing the tire pressure monitoring indicator to light up. Simply performing a tire pressure reset will resolve this issue. Damaged Tire Pressure Sensor: The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the tire inflation valve. If the sensor is damaged due to impact while driving, it can trigger the tire pressure warning light. In such cases, the only solution is to replace the sensor with a new one.
1
0
Share

How to Install License Plate Nuts?

Installation method is as follows: 1. Prepare the screw components, including spacers, screws, and caps, which need to be obtained from the vehicle management office. Do not use your own screws for fixing. If the screw components are not fixed according to regulations, you may face penalties; 2. At the location where the license plate is to be mounted on the car, you can see the fixing points. Place the side of the license plate with the license plate number facing outward, then align it with the car's fixing points, ensuring the middle holes are also aligned; 3. Insert the screws into the holes and secure them with a flat-head screwdriver. Do not tighten them completely; just ensure the screws do not fall out; 4. Install screws at all other fixing points, similarly securing each screw without tightening them completely. If tightened prematurely, it will be difficult to adjust the position later; 5. After all screws are in place, adjust the license plate position, then fully tighten all screws; 6. Finally, align the caps with the spacers and press them into the screws with slight force to secure them in place. The license plate installation is now complete.
3
0
Share

What are the differences between cornering lights and adaptive headlights?

Turn assist lights are fundamentally different from adaptive headlights in the following ways: 1. Adaptive headlights achieve their function by rotating the reflector cup and bulb; turn assist lights use a small bulb set at a special angle within the headlight that lights up at specific times to achieve the same effect. 2. In practical use, the effectiveness of turn assist lights in illuminating blind spots is not as good as that of adaptive headlights. Additional information: Details about turn assist lights and adaptive headlights are as follows: 1. Turn assist lights refer to a separate set of bulbs that light up on one side when the driver turns the steering wheel (some vehicles also use fog lights as turn assist lights), helping to illuminate the blind spots in the curve while driving. Shortly after the steering wheel is straightened, the single-sided turn assist light will turn off. 2. Adaptive headlights, also known as dynamic bending lights, refer to headlights that can rotate a certain angle in the direction of the turn when the car is turning, expanding the field of vision. This helps to illuminate the "unreached" area in advance, providing all-around safety lighting to ensure the driver has the best visibility at all times.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.