Is there a minimum speed limit on urban roads?

3 Answers
Noah
07/28/25 3:24pm
There is no minimum speed limit on urban roads, but there is a maximum speed limit. Expressways and freeways have minimum speed limits. Additional information: The following is an introduction to speed limits on urban roads: 1. Roads without a center line: The speed limit is 30 kilometers per hour for urban roads and 40 kilometers per hour for highways. 2. Roads with only one motor vehicle lane in the same direction: The speed limit is 50 kilometers per hour for urban roads and 70 kilometers per hour for highways. 3. Speed limits under special weather conditions: In case of abnormal weather with visibility less than 50 meters, the maximum speed limit is 30 kilometers per hour. When road conditions are abnormal (such as ice, snow, mud, etc.), the speed should also not exceed 30 kilometers per hour.
Was this review help?
6
2
Share
DeFrank
08/11/25 7:46pm
I've been driving in the city for over a decade. On urban roads, I mainly pay attention to the maximum speed limit signs. For instance, main roads usually have speed limits of 50 or 60 kilometers per hour. Minimum speed limits? Not very common. Urban environments are highly variable with heavy traffic and pedestrian flow, so setting rigid low speed limits isn't reasonable. In areas like school zones or during congestion, reducing speed below 10 km/h can be necessary for safety without violating regulations. I recommend maintaining around 20 km/h when conditions allow. Driving too slowly might prompt honking from vehicles behind, and police might even issue warnings for obstructing traffic. From my experience, keeping between 20-30 km/h is optimal - it avoids rear-end collision risks, ensures smooth intersection passage, and reduces congestion during rush hours. Always observe road conditions and signage carefully. Occasionally, tunnels or bridge areas may display minimum speed reminders, but these are rare in city centers. Ultimately, rely on your judgment to adjust speed appropriately - the key is not to slow down overall traffic flow.
Was this review help?
14
4
Share
Expand All
WalterRose
09/29/25 5:17am
I have always been quite attentive to traffic regulations and have researched related information. Urban roads typically prioritize maximum speed limits, generally set between 40 to 60 kilometers per hour, while minimum speed standards are mostly not fixed, except on highways where it may require no less than 60. This is because urban road conditions are complex, with pedestrians and bicycles moving around, necessitating constant speed reduction to ensure safety. The law requires avoiding excessively slow driving to prevent traffic congestion, but specific speeds rely on the driver's discretion. It's advisable to maintain a speed of at least 15 kilometers per hour to keep traffic flowing smoothly; especially at certain elevated road entrances or tunnels, there might be signs indicating a minimum of 30. From a safety perspective, maintaining a steady speed around 20 can reduce accidents, particularly during rainy days with poor visibility. Overall, don’t worry too much about rigid rules—flexibility is key.
Was this review help?
20
1
Share
Expand All
More Forum Discussions

What Happens When the Fuel Pump Relay Fails?

Fuel pump relay failure symptoms: starter does not rotate; starter cranks weakly; starter spins freely. The relay serves both as a control switch and the controlled component (actuator). The fuel pump relay acts as the control switch for the fuel pump, but its coil can only complete the circuit through the ECU's ground point when the driving transistor in the ECU is activated. Possible causes of starter failure to rotate include: 1. Power supply issues - severely depleted battery, sulfated or short-circuited plates, poor contact between battery terminals and cable clamps, loose connections in starting circuit wiring. 2. Starter malfunctions - poor contact between commutator and brushes, open or short circuits in field windings or armature windings, grounded insulation brushes, open/short/grounded solenoid switch coils or burnt contacts. 3. Starting relay faults - open/short/grounded relay coils or poor contact at relay points. 4. Ignition switch problems - loose wiring or internal contact failure. 5. Starting circuit wiring faults - open circuits, poor wire connections or disconnections in starting circuits.
10
0
Share

Differences Between Regular Motorcycles and Light Motorcycles

Differences between regular motorcycles and light motorcycles: 1. Different nature: Light motorcycles have lower maximum design speed, displacement, or total motor power compared to regular motorcycles, with technical parameters and performance falling between electric bicycles and motorcycles. Regular motorcycles are driven by gasoline engines and are two-wheeled or three-wheeled vehicles steered by handlebars. 2. Different characteristics: Regardless of the driving method, the maximum design speed of a light motorcycle does not exceed 50 km/h; its maximum design speed, displacement, or total motor power are all lower than those of regular motorcycles. Key points for safe motorcycle riding are as follows: 1. Always pay attention to the road conditions ahead, checking for slippery sections, uneven or damaged road surfaces, gravel, obstacles in the road, oil stains, or accumulated small stones on curves. 2. When changing lanes or starting, use the rearview mirror to check the situation behind you and confirm safety before proceeding. Avoid sudden stops or deceleration unless necessary to prevent rear-end collisions. When turning, reduce speed before turning and strictly avoid decelerating during the turn. 3. Although two-wheeled motorcycles are highly maneuverable, they must not weave between lanes of moving vehicles or overtake from the right side. Such driving methods are not only extremely dangerous but also make other drivers nervous, increasing the risk of traffic accidents.
9
3
Share

What causes the sudden inability to depress the clutch in a Kia K3?

Reasons for the inability to depress the clutch in a Kia K3: the clutch is not fully engaged; the handbrake is not released; the gear is stuck and not fully engaged; excessive wear of the clutch friction plate. Related introduction: 1. Principle of the clutch: The car clutch is a mechanism that disconnects and connects the power between the engine and the transmission. When the clutch pedal is depressed, the force applied to the pedal is transmitted through leverage to push the clutch fork, which in turn moves the release bearing. 2. Types of clutches: The clutch is a commonly used component in mechanical transmissions, allowing the transmission system to be separated or engaged at any time. Its basic requirements include: smooth engagement, quick and thorough separation; easy adjustment and repair; compact size; lightweight; good wear resistance and sufficient heat dissipation capacity; easy and effortless operation. Commonly used types are jaw clutches and friction clutches.
8
3
Share

What Causes White Smoke from the Engine Exhaust Pipe?

White smoke from a car engine is caused by low temperatures. During engine operation, the exhaust gases expelled encounter the cold external environment, leading to instant condensation. The resulting water vapor produces a large amount of fog-like white smoke. There are many reasons for white smoke emission, mainly including the following aspects: 1) The engine temperature is too low. Some diesel fuel does not burn completely and turns into oil vapor, which is expelled with the exhaust gases, resulting in white smoke. 2) Water in the fuel system. If there is water in the fuel or combustion chamber, it is heated by the combustion heat in the cylinder and turns into steam, which is expelled from the exhaust pipe as white smoke. 3) Delayed fuel injection. Due to late injection timing, the cylinder temperature has already dropped when the fuel is injected, causing some diesel to remain unburned and turn into oil vapor, leading to white smoke. 4) Poor fuel injector atomization. Inadequate atomization prevents complete combustion of diesel, which then mixes with the high-temperature exhaust gases from normally operating cylinders in the exhaust pipe, resulting in white smoke. 5) Low cylinder pressure. Some diesel fuel turns into oil vapor without burning, thus causing white smoke from the exhaust pipe.
15
3
Share

What is the default 4-digit PIN for Audi?

Audi's default 4-digit PIN is either 0000 or 1234. The PIN code is used for Bluetooth connection pairing. When two devices perform Bluetooth pairing, they must enter the same password to establish the connection, and typically this password consists of four digits. Below is relevant information: How to check the PIN code: The car's PIN code can be found in the vehicle's electronic anti-theft system or in the accompanying user manual. The user manual includes a confidential envelope containing the engine electronic anti-theft system PIN code. Purpose of the PIN code: The car's PIN code serves as the vehicle's password, commonly referred to as the engine electronic anti-theft system. For vehicles, the most obvious function of the PIN code is to prevent car theft. In cases such as a damaged anti-theft converter or other faults, repair shops can use the car's PIN code for maintenance. Thus, the car's PIN code acts as a vehicle identification number, ensuring the vehicle's security. The PIN code can also be used for key programming and repairing the electronic anti-theft system. Therefore, once a technician knows the car's PIN code, they can perform repairs on the engine anti-theft system.
9
0
Share

What is the function of the anti-collision beam?

The function of the anti-collision beam is to absorb and mitigate external impact forces or to protect the front and rear parts of the vehicle body. The anti-collision beam is a U-shaped channel formed by stamping cold-rolled steel plates and is connected to the longitudinal beams of the vehicle frame, serving as the first barrier of passive safety in automobiles. Anti-collision beams are divided into front and rear anti-collision beams. Below is an introduction to the related content: 1. The front anti-collision beam is usually connected to the longitudinal beams of the vehicle body, protecting rear components such as the radiator and reducing damage in minor accidents. The materials are generally steel, fiberglass, or aluminum alloy, with a thickness of 1.5-3mm. In fact, there is usually a layer of foam supporting the outer plastic skin of the front anti-collision beam, primarily serving to protect pedestrians. 2. The rear anti-collision beam is generally thicker than the front beam, around 2-3mm. It is connected to the longitudinal beams under the vehicle chassis, aiming to reduce impact in minor rear-end collisions and protect the thin spare tire rack and rear fenders, among other parts. Without a rear anti-collision beam, even a minor rear-end collision could cause the plastic skin to fail to withstand any impact.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.