Is there a layer of glue-like substance on the car headlight surface?

How to Reset the Maintenance Light on MG MG6?

The method to reset the maintenance light on MG MG6 is: 1. Turn on the ignition switch, hold down the reset button 5 with one hand, and turn off the ignition switch with the other hand; 2. Keep holding the reset button 5 without releasing until the clock and mileage on the dashboard completely disappear (the dashboard should show no display, black screen), then release the button. Taking the 2020 MG MG6 as an example, its body dimensions are: length 4704mm, width 1848mm, height 1466mm, with a wheelbase of 2715mm. The 2020 MG MG6 features a front suspension type of MacPherson independent suspension and a rear suspension type of multi-link independent suspension.

6

5

Share

What causes jerking and fuel cut-off when accelerating suddenly?

The reasons for jerking and fuel cut-off when accelerating suddenly are as follows: There may be three main causes: 1. Excessive carbon deposits in the throttle body, fuel injectors, or intake manifold: Many malfunctions are caused by carbon deposits, and some vehicles may experience jerking due to this issue. It is recommended to regularly clean carbon deposits. 2. Poor fuel quality: This leads to incomplete combustion, and qualified fuel should be used instead. 3. Faulty spark plugs, ignition coils, etc., causing misfires. It is necessary to visit a repair shop for inspection and timely repairs to avoid further safety hazards.

16

0

Share

Where is the ABS pump located in a car?

The ABS pump is located near the firewall in the car's engine compartment. The working principle of the ABS pump is: relying on highly sensitive wheel speed sensors installed on each wheel and the vehicle's speed sensor, under computer control, when emergency braking is detected and a wheel is about to lock up, the computer immediately commands the pressure regulator to release pressure from that wheel's brake caliper, allowing the wheel to resume rotation. The ABS pump, also known as the Anti-lock Braking System, features anti-skid and anti-lock characteristics. Its working process involves a cycle of locking and releasing, keeping the vehicle in a state of near-lock rolling, effectively overcoming issues like deviation, side-slip, and fishtailing during emergency braking, and preventing loss of vehicle control.

17

0

Share

Does the Roewe i5 comply with the China VI emission standard?

Roewe i5 complies with the China VI emission standard. The China VI standard, also known as the National Sixth Stage Emission Standard for Motor Vehicles, is established to prevent environmental pollution caused by exhaust emissions from compression-ignition and gas-fueled spark-ignition engine vehicles, protect the ecological environment, and safeguard human health. The Roewe i5 is a high-performance internet-connected mid-size sedan under the Roewe brand, with dimensions of 4607mm in length, 1818mm in width, and 1489mm in height, and a wheelbase of 2680mm. The Roewe i5 features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.5L naturally aspirated engine, delivering a maximum power of 88kW and a maximum torque of 150Nm.

5

0

Share

What Causes Engine Vibration in the Hyundai Elantra?

The reason for engine vibration in the Hyundai Elantra is: severe carbon buildup or a dirty air filter, and it is recommended to clean and replace them promptly. The engine is the core part of the powertrain, with the cylinder as its main component, and it serves as the power source for the entire vehicle. Taking the 2020 Hyundai Elantra as an example, in terms of suspension, the front suspension is a MacPherson strut independent suspension, and the rear suspension is a torsion beam non-independent suspension. The 2020 Hyundai Elantra is a compact car with body dimensions of: length 4610mm, width 1800mm, height 1450mm, a wheelbase of 2700mm, and a curb weight of 1319kg.

19

2

Share

How to Replace the Battery in a Geely Borui Key?

The method to replace the battery in a Geely Borui key is: pull out the mechanical key, then use a screwdriver to pry open the key, and you can replace the battery. When reinstalling, follow the reverse steps. The key maintenance methods are: 1. Do not frequently place it with metal items; 2. Prevent the smart key from falling or being impacted; 3. Avoid exposing the smart key to high temperatures or contact with liquids; 4. Do not place the key with electronic devices. The Geely Borui has a length, width, and height of 4986mm, 1861mm, and 1513mm respectively, with a wheelbase of 2870mm. It is equipped with a 1.8T turbocharged engine, with a maximum power of 135kw, and matched with a 7-speed dual-clutch transmission.

12

2

Share

Is there a layer of glue-like substance on the car headlight surface?

How to Reset the Maintenance Light on MG MG6?

What causes jerking and fuel cut-off when accelerating suddenly?

Where is the ABS pump located in a car?

Does the Roewe i5 comply with the China VI emission standard?

What Causes Engine Vibration in the Hyundai Elantra?

How to Replace the Battery in a Geely Borui Key?

Why was the Geely Xingyue L discontinued so quickly?

What does AOFF mean on a car?

How to reset the maintenance light on a Hyundai Elantra?

What is the Basic Working Principle of an Oscilloscope?