Is there a big difference between Audi 40 and 45?

1 Answers
SanJessica
07/30/25 4:29am
Audi 40 and 45 are not much different. The differences between Audi 40 and 45 are as follows: Power: The maximum power of the 40 model is 140kw, with a maximum torque of 320 Nm, while the 45 engine has a maximum power of 185kw and a maximum torque of 370 Nm. This engine is also equipped with AVS technology and hybrid injection technology, and uses an aluminum alloy cylinder head. Engine: The 40 is a low-power version of the 2.0-liter turbocharged engine, while the 45 is a high-power version of the 2.0-liter turbocharged engine. Both engines are essentially 2.0-liter turbocharged engines, with the only differences being in maximum power and maximum torque.
Was this review help?
8
3
Share
More Forum Discussions

How to Clear the Tire Pressure Warning Light on Volkswagen Sagitar?

Methods to clear the tire pressure warning light on Volkswagen Sagitar: 1. Turn off the engine and wait for about 2 minutes before restarting the vehicle; 2. Inflate or deflate the tires and observe the tire pressure light display on the dashboard; 3. Locate the settings button on the car's central console to reset the tire pressure; 4. Use a specialized diagnostic tool to clear the fault code. The Sagitar is a joint-venture A+ class sedan brand under FAW-Volkswagen, with body dimensions of 4753mm in length, 1800mm in width, and 1462mm in height, and a wheelbase of 2731mm. It is equipped with a turbocharged, inline four-cylinder 16-valve electronically controlled direct fuel injection engine, paired with a 7-speed dry dual-clutch transmission.
19
3
Share

What is the alignment method for the timing chain of the LaCrosse 2.4L?

The alignment method for the timing chain of the LaCrosse 2.4L: 1. Rotate the crankshaft to align the mark on the transmission with the scale line on the flywheel. 2. Rotate the camshaft to align the mark on the camshaft timing gear with the bottom of the valve chamber. 3. Locate the driving end of the oil pump shaft and align the raised rectangular side of the driving end with the direction of the crankshaft. 4. Insert the distributor assembly into the mounting hole and secure it. 5. Align the distributor rotor with the mark on the housing, cover the distributor cap, and then connect the cylinder wires and various internal components. 6. Install the timing belt, start the engine for inspection, and readjust if any issues are found. The LaCrosse 2.4L has a body size of 5005mm in length, 1858mm in width, and 1500mm in height, with a wheelbase of 2837mm. This vehicle is equipped with a 2.4L direct injection engine, delivering a maximum power of 137kw and a maximum torque of 240nm.
16
2
Share

How to install the front license plate on an Audi A4L?

Audi A4L front license plate installation method: 1. Prepare the necessary tools: one rivet gun, one Phillips screwdriver, one pack of license plate fasteners, two small screws, and two rivet nuts; 2. Take out the rivet nuts and rivet gun, and install the rivet nuts onto the rivet gun; 3. Use the rivet gun to secure the rivet nuts onto the car's bumper, aligning them with the two holes on the bumper; 4. Press firmly towards the center, then remove the rivet gun; 5. Take out the car license plate, position it correctly, ensuring equal distance on both sides; 6. Use the Phillips screwdriver to fix the license plate fasteners onto the four holes of the license plate, securing the plate to the bumper; 7. Take out the caps from the license plate fasteners and press them onto the fasteners to complete the installation. The Audi A4L is a mid-size car under FAW-Volkswagen Audi, with dimensions of 4858mm in length, 1847mm in width, and 1439mm in height, and a wheelbase of 2908mm.
1
4
Share

How Many Kilometers is Considered the Break-in Period for a Car?

The break-in period for a car is typically between 1,000 to 3,000 kilometers. During this period, it is essential for the owner to control the speed appropriately, avoiding sudden braking and rapid acceleration. It is also recommended to warm up the engine before driving to ensure proper lubrication and prevent unnecessary malfunctions that could affect normal usage. Characteristics of a new car's break-in period: 1. More minor issues may arise. It is normal for a new car to experience minor faults during the break-in period, as the components have not yet fully adapted to each other. Poor driving habits can further increase the likelihood of faults, so owners should pay extra attention while driving. 2. Lubricating oil tends to degrade faster. The high friction between new components can raise the temperature of the lubricating oil during operation, and impurities may also mix into the oil, leading to oxidation and deterioration of the lubricant.
2
4
Share

Is ETC Required?

ETC installation is necessary. According to the State Council's regulations, starting from 2020, vehicles without ETC will not enjoy toll discounts. In the future, only one manual lane will be retained at highway toll stations, and tolls can only be paid through manual lanes. Additionally, newly installed ETC devices cannot be used on highways immediately; they must be activated first. During free holiday periods, ETC users can still use highways, and no fees will be deducted when passing through ETC lanes. ETC Billing Principle: Highways will have one or more ETC lanes. Through dedicated short-range microwave communication between the vehicle's windshield-mounted electronic tag and the microwave antenna in the ETC lane, and using computer networking technology for backend settlement with banks, vehicles can pay tolls without stopping at toll stations. All of this operates on the principle of "pass first, deduct later." Benefits of Installing ETC: Time-saving: Eliminates the hassle of waiting in queues. Green and eco-friendly: Reduces noise and exhaust emissions by eliminating stops at toll stations, lowering pollution. Reduces wear and tear: Saves costs by decreasing the frequency of vehicle starts and stops, reducing wear and fuel consumption. Improves efficiency: ETC lanes can theoretically increase traffic flow efficiency by 2-3 times, making traditional ETC faster, more advanced, and more high-tech. Compared to license plate payment, ETC technology is more mature and advantageous. More policy support: The State Council's "13th Five-Year Plan for the Development of a Modern Comprehensive Transportation System" explicitly states, "By 2020, key city clusters will achieve interoperability of transportation cards, and the proportion of vehicles using ETC will significantly increase." It also sets a target of "50% ETC usage rate for road passenger vehicles by 2020" in the main indicators of the "13th Five-Year" comprehensive transportation development plan. More future possibilities: In addition to continuously improving the convenience of ETC installation and usage rates for passenger vehicles, future efforts will include promoting ETC for trucks and exploring deeper integration of ETC systems with vehicle-to-vehicle communication, vehicle-to-infrastructure coordination, and other smart transportation developments. This will provide comprehensive travel services for vehicle owners, meaning more application scenarios will support ETC usage.
5
4
Share

What are the main functions of antifreeze?

Antifreeze serves several key purposes: 1. Cooling function: Cooling is the fundamental role of antifreeze. When the engine operates, it generates a significant amount of heat, with approximately 60% of this heat being dissipated into the surrounding space through the cooling system. 2. Heat dissipation: Antifreeze provides efficient heat dissipation, removing excess thermal energy from the engine to control the temperature of critical metal components. 3. Freeze protection: During winter when temperatures are low, antifreeze contains substances that lower the freezing point of water, allowing vehicles to continue operating in cold weather by preventing the cooling system from freezing. 4. Corrosion prevention: The cooling system consists of components such as radiators, water pumps, cylinder blocks, cylinder heads, and water distribution pipes made from various metals including steel, cast iron, brass, copper, and aluminum. Due to differing electrode potentials among these metals, electrochemical corrosion can occur in the presence of electrolytes. Additionally, acidic byproducts formed from the decomposition of glycol-based substances in the coolant, as well as acidic exhaust gases from fuel combustion that may infiltrate the cooling system, can accelerate corrosion within the system.
2
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.