Is the Wildlander Four-Wheel Drive a Full-Time Four-Wheel Drive System?

Does coasting in neutral harm a dual-clutch transmission?

Coasting in neutral is dangerous and wastes fuel, and it may even damage the transmission in automatic vehicles. When shifting into neutral (N) while driving normally, the transmission output shaft rotates at high speed while the engine idles, leading to insufficient lubrication from the transmission oil pump. This worsens lubrication conditions and affects the multi-plate clutches inside the transmission. Although power is cut off, the driven plates continue spinning at high speed due to wheel movement, increasing the risk of slippage—a highly hazardous situation. Additional considerations for coasting in neutral: 1. Reduced Safety: Coasting in neutral significantly compromises safety. Vehicle propulsion relies on engine torque, which is weaker in higher gears, resulting in sluggish throttle response and slower acceleration. For proper overtaking, downshifting is recommended. In automatic transmissions, fully depressing the throttle prompts the transmission to downshift, delivering adequate torque. 2. Increased Fuel Consumption: Coasting in neutral does not save fuel and may even increase consumption due to the operation of fuel-injected engines. These engines adjust fuel injection based on programmed parameters. In gear, releasing the throttle activates a coasting mode where the engine stops injecting fuel for extended periods. In neutral, however, the engine enters idle mode and continues injecting fuel.

8

4

Share

What to Do When the Rearview Mirror's Vertical Adjustment Fails?

When the rearview mirror's vertical adjustment fails, there are several possible scenarios: Button contact failure. The adjustment buttons for up-down and left-right directions malfunction. In this case, first check the switch—it's highly likely that the switch is dirty. Usually, cleaning it will restore normal function. Since dismantling the entire control panel is difficult, it's recommended to go directly to an auto repair shop or a 4S shop and have professionals clean it. Misalignment of the white screw inside the mirror. During adjustment, the motor makes a working sound and shows signs of operation, but the adjustment fails. Solution: Insert the white screw back into the rubber sleeve. The mirror lens can be pried off directly—apply force from the bottom of the lens, pushing upward and outward. The center of the lens has a large spherical slot; once opened, you can see the white screw. Motor gear damage or wiring harness issues. In this situation, you can only go to a 4S shop or an auto repair shop, have professionals inspect it first to identify the problem, and then proceed with targeted repairs.

14

4

Share

How to Solve the High Fuel Consumption of Baojun 730?

Here are the solutions to the high fuel consumption of Baojun 730: Press the accelerator gently. Pressing the accelerator gently can save fuel, because stepping on it suddenly will cause the engine speed to drop sharply, creating a drag effect that offsets part of the driving inertia, making the car vibrate and increasing fuel consumption. Start smoothly. Start in a low gear, press the accelerator pedal slowly, and accelerate gradually to reduce fuel consumption. If you rev the engine hard to speed up when starting, it will not only damage the car but also increase fuel consumption. Maintain a certain speed. Driving at a constant speed in a straight line is the most fuel-efficient. The optimal speed for small-displacement cars is 60-80 km/h, and for medium-displacement cars, it is 80-100 km/h. Keep a safe following distance. Maintaining a proper following distance while driving can save fuel. If the road is congested and the car in front brakes frequently, keeping enough distance allows you to slow down calmly and reduces the number of times you need to brake. Control the engine speed. Generally, the optimal engine speed for fuel-injected cars is around 2200-2500 rpm. Reduce braking. Control the driving gear and shift speed.

14

0

Share

What is the distance between two vehicles when using a flexible towing device?

The distance between two vehicles when using a flexible towing device should be maintained between 4 meters and 10 meters. Article 61 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China" stipulates that when using a flexible towing device, the distance between the towing vehicle and the towed vehicle should be greater than 4 meters and less than 10 meters. Extended content: 1. Preparation: When towing, attach both ends of the towing rope to the towing hook of the towing vehicle and the tow hook of the towed vehicle. 2. Starting: When using a flexible towing link, first determine the communication signals and precautions between the towing vehicle and the towed vehicle. 3. Driving: When driving with a flexible towing link, the front vehicle should maintain a constant speed. 4. Turning: When encountering a curve, the front vehicle should slow down in advance and use gestures and horn signals to alert the rear vehicle. It should try to drive on the outer side of the curve. 5. Driving on slopes: When going uphill, the front vehicle should position itself slightly offset from the rear vehicle to prevent collision if the front vehicle rolls back. When going downhill, the front vehicle should stay on the right side of the road and increase speed appropriately to prevent the towing rope from becoming too loose and difficult to control. 6. Braking and stopping: During flexible towing, unless under special circumstances, the front vehicle should avoid using the brakes and must not brake suddenly. Choose a wide and flat area for stopping. The front vehicle should first use gestures to alert the rear vehicle, then slow down and move to the side. When the rear vehicle is expected to enter the roadside, apply the brakes smoothly to stop.

20

5

Share

What is the Reverse Parking Control Line?

In the driving test's Subject 2 (reverse parking), the control line means that neither the front nor the rear of the car can cross the line, and the vehicle must not touch the lines on either side. Reverse parking has been a mandatory test item for obtaining a small car driver's license since 2013. It assesses the driver's ability to maneuver the vehicle in a confined space. Reverse parking is a key evaluation point in the driver's test, requiring the examinee to correctly reverse the vehicle into a parking space from both sides while in motion. Methods for reverse parking: Adjust the side mirrors: During the test, the examinee should adjust the mirrors to a suitable angle for better visibility of the ground markings. When the examinee can see the rear door handle and the wheels in the mirror, it indicates that the mirrors are properly adjusted. Use the mirrors: Checking the mirrors is essential for reverse parking, and it's important to learn how to use them correctly. The examinee can observe whether the car body is parallel to the markings by looking at the left rearview mirror. Mastering mirror usage is highly beneficial for successful reverse parking. Maintain proper distance between the car body and the side line: The requirement for reverse parking is that the vehicle should be about 1.5 meters away from the starting line and the roadside line. This distance should be neither too large nor too small. If it's too large, the wheels might cross the line when parking; if it's too small, the front of the car might stick out. Therefore, the examinee must learn to maintain an appropriate distance between the car body and the side line. Control the speed: There are specific speed requirements for reverse parking. The vehicle must not move too quickly, and you can't just "zoom" into the parking space. This often requires using the clutch, so the examinee should practice clutch control. The slower the speed, the better, but it shouldn't be excessively slow either.

14

2

Share

Why does 12123 show out-of-town traffic violations from many years ago?

Here are the specific reasons why the Traffic Management 12123 app may display out-of-town traffic violations from many years ago: 1. Data anomalies: Issues with the traffic violation information system of the traffic police department. When the system is upgraded by local traffic police departments, abnormal data may appear. 2. Improper handling: The vehicle management office failed to properly process violations associated with license plates of scrapped vehicles, leading to these violations appearing on new vehicles when the license plates are reused. 3. Out-of-town violations: In the past, there were no SMS notifications for out-of-town violations, resulting in such records appearing in the traffic violation system after interconnection.

17

0

Share

Is the Wildlander Four-Wheel Drive a Full-Time Four-Wheel Drive System?

Does coasting in neutral harm a dual-clutch transmission?

What to Do When the Rearview Mirror's Vertical Adjustment Fails?

How to Solve the High Fuel Consumption of Baojun 730?

What is the distance between two vehicles when using a flexible towing device?

What is the Reverse Parking Control Line?

Why does 12123 show out-of-town traffic violations from many years ago?

What is drive-mode

How old must a car be to meet China V emission standards?

Which Side Goes First When Both Vehicles Are Going Straight at an Intersection?

Reasons Why Three Windows of the 7th Generation Accord Cannot Be Lowered?