Is the Subject 2 Test Judged by Computer or Human?

1 Answers
SanElena
07/30/25 8:29am
Subject 2 is judged by computer. Here are the details about Subject 2: 1. Subject 2, also known as the small road test: It is part of the motor vehicle driver's license assessment and refers to the field driving skills test. 2. Test items for small vehicles in Subject 2: Include five mandatory tests - reversing into a garage, parallel parking, stopping and starting on a slope, right-angle turns, and curve driving (commonly known as S-curves). 3. Test items for large vehicles in Subject 2: Include stake test, stopping and starting on a slope, parallel parking, crossing a single-plank bridge, curve driving, right-angle turns, passing through a width-limited gate, navigating continuous obstacles, driving on bumpy roads, making U-turns on narrow roads, as well as simulated highway driving, continuous sharp turns on mountain roads, tunnels, driving in rain (fog), slippery roads, and emergency handling.
Was this review help?
9
3
Share
More Forum Discussions

Do You Need to Press the Brake When Shifting into Reverse Gear in a Manual Transmission?

No. When shifting gears, the clutch and throttle must be well-coordinated. Press the clutch pedal all the way down, then release the throttle pedal, and quickly shift into the corresponding gear. Master the timing of gear shifting: When driving a manual transmission car, the most important thing is to master the timing of gear shifting. Shift gears when the engine speed is around 2000 RPM. First reduce the throttle and then press the clutch, so the clutch won't be forced to disengage, and then shift gears. Gear shifting sequence: The gear shifting sequence must be first gear → second gear → third gear → fourth gear → fifth gear. Skipping gears is not recommended. The downshifting sequence depends on the vehicle speed. Based on your car's condition, generally downshift when the engine speed is below around 1500 RPM.
19
4
Share

Where is the drainage hole of the Bora car door located?

The drainage holes of the Bora car door are located at the lower part of the door panel (usually 1-2 holes). Here is some additional information: 1. Generally, there are no hoses to guide the drainage at the lower part of the door panel, and rainwater directly flows through the rust-proof treated door panel for discharge. Due to the low position of the drainage holes, vehicles that frequently drive on muddy roads may find these holes easily clogged by mud, so owners should pay attention to regular checks. 2. Sometimes, the drainage holes may be blocked by rubber plugs, which should be promptly removed to allow accumulated water to drain and prevent door rust. The drainage holes are usually positioned at the lowest part of the door, allowing water to naturally flow out due to gravity. Additionally, after washing the car, it is important to check the drainage holes at the bottom of the door to ensure they are not blocked by debris, and to clean them in time to prevent rust caused by water accumulation.
12
4
Share

Why is the metal box connected to the exhaust pipe dripping water?

The reason for water dripping from the metal box connected to the exhaust pipe: After gasoline is completely burned, it produces water and carbon dioxide. At high temperatures, water exists as water vapor, which is colorless and transparent. However, when the temperature drops below 100 degrees Celsius, the water vapor condenses into water. If the condensed water droplets are suspended in the air, they appear as white gas. When the ambient temperature is low, the white smoke from the exhaust pipe is water vapor. If the condensed water droplets accumulate, they turn into water. The exhaust pipe is equipped with a device to reduce vibration and noise, facilitate installation, and prolong the life of the exhaust muffler system. It is installed between the engine exhaust manifold and the muffler, making the entire exhaust system flexibly connected.
6
1
Share

How to Distinguish Between the Reiz Big V and Small V?

Distinguishing between the Reiz Big V and Small V can be done by checking the engine displacement: the Big V has a 3.0L displacement, while the Small V has a 2.5L displacement. The Reiz is the domestic name for the Japanese Toyota MARKX model, which features a long wheelbase, shortened front and rear overhangs, and wider wheel tracks to accommodate larger tires positioned as close to the four corners of the body as possible. The vehicle height is reduced by lowering the seating position for occupants. The Reiz's lighting is distinctive, with front headlights featuring a three-beam pea-pod shape, and fog lights, low beams, and high beams arranged in a row. The overall size is not large, and the tail lights appear particularly striking with their transparent covers, exuding a sporty vibe.
10
2
Share

What is the reason for the P0012 camshaft position A timing retardation?

p0012 camshaft timing retardation reasons are as follows: 1. Low octane rating: Low gasoline octane rating or engine disengagement causes engine misalignment, resulting in camshaft retardation and altering the position sensor signal data. 2. Stuck: Oil pressure control valve (OCV) stuck. CVVT actuator gear mechanically jammed. 3. Wear: Oil pump wear, oil pump pressure regulating valve stuck, or system blockage. 4. Belt issue: Incorrect timing belt or chain alignment. 5. Wiring problem: Abnormal current in CVVT control circuit, poor contact in solenoid valve relay contacts and wiring harness, and poor ECM loop control.
19
2
Share

How to Remove the Navigation System of Baojun 310?

Steps to remove the navigation system of Baojun 310: 1. First, remove the left air vent; 2. Then, remove the right air vent until both left and right air vents are detached; 3. Next, remove the air conditioning remote panel and control integration; 4. The vehicle information panel also needs to be removed before the navigation system can be taken out. The car navigation system features GPS global satellite positioning functionality. Simply input the destination into the car navigation system, and the system will automatically calculate the optimal route based on the electronic map. The Baojun 310 has dimensions of 4032mm in length, 1680mm in width, and 1450mm in height, with a wheelbase of 2550mm. The vehicle is equipped with an engine that delivers a maximum horsepower of 80Ps, a maximum power of 59kW, and a maximum torque of 112Nm.
13
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.