Is the steering wheel of Wuling Rongguang too heavy?

1 Answers
ColeDella
07/24/25 5:25pm
The main reasons for the excessively heavy steering wheel of Wuling Rongguang are as follows: 1. Check for oil leakage. If oil is insufficient, replenish it to the normal range. If oil is sufficient, check whether the power steering pump belt is too loose. If it is too loose, tighten the belt. Also, check whether the oil is too dirty, which may lead to poor fluidity. Generally, it should be replaced every 2 years or 60,000 kilometers. 2. Check whether the fuse is burnt out and whether there is an open circuit or a short to ground in the wiring. 3. Check the tire pressure. Air leakage can also make the steering heavier, so it is necessary to inflate the tires. 4. If the power steering effect is much worse than before, there should be a problem with the power steering system. Please check whether the power steering oil is insufficient and whether the power steering pump is working normally.
Was this review help?
2
2
Share
More Forum Discussions

Where is the wiper fuse located in the Volkswagen Tiguan?

The wiper fuse of the Volkswagen Tiguan is located in the fuse box at the lower left of the dashboard in the driver's compartment. Wiper maintenance tips: 1. In winter when the weather is colder, promptly clean any accumulated water on the wiper blades and windshield after washing the car to prevent the wipers from freezing and malfunctioning. 2. Regularly inspect your wiper blades for cracks or damage. If any are found, replace them immediately to avoid scratching your car's windshield. 3. Avoid parking outdoors for extended periods when the car is not in use. If unavoidable, lift the wipers to prevent them from freezing to the windshield when snow melts. 4. After each use, promptly remove any ice buildup on the wiper blades. 5. Turn off the wipers before shutting down the engine. In heavy snow conditions, lift the wiper blades at night to prevent them from freezing.
8
3
Share

How to Cancel the Tire Pressure Warning?

There are three methods to eliminate the low tire pressure warning light: 1. Check and confirm whether the tire pressure is normal. If there is an issue, adjust it to the standard pressure, then drive for a few kilometers. Generally, the system will automatically reset at this point. 2. If the tire pressure is confirmed to be normal, visit an auto service shop to inspect the tire pressure sensors and clear the fault code. 3. Locate the settings button on the central console for manual reset, usually by pressing the SET key. The following are the reasons for the tire pressure warning: 1. Decreased tire pressure, mostly due to insufficient tire pressure or a tire leak, requiring inspection. Insufficient pressure requires inflation; a leaking tire needs repair. 2. Inaccurate pressure testing may cause this. You can restart and observe. If the warning persists, it is likely due to reason 1; if the warning stops, there is usually no problem.
4
2
Share

How to Determine if a Tire is Tubeless?

Check the tire valve. The valve of a tubeless tire is sealed with rubber against the rim, while ordinary tires do not require sealing and mostly use standard metal valves. Look for the TUBELESS marking on the tire, which indicates a tubeless tire. Additionally, if the wheel rim is of the spoke type, it is definitely not a tubeless tire. Below are precautions for using tubeless tires: 1. Maintain the specified air pressure. Tubeless tires are made of high-quality rubber, offering good elasticity and flexibility, with a wide range of air pressure adaptability. Even at high pressure, they do not feel as hard as regular tires, so a pressure gauge must be used to check the pressure. Unless punctured, tubeless tires generally do not lose air on their own. Therefore, always use a pressure gauge to check and maintain the specified pressure when inflating, and never rely on feel to decide whether to add air as with regular tires. 2. Not suitable for overloading. Tubeless tires are wear-resistant but not pressure-resistant, making them unsuitable for excessive overloading.
5
4
Share

How to Open the Fuel Tank Cap on a Cruze?

The fuel tank cap of the Cruze is located on the right side; simply press the fuel tank cap to open it. Here is an introduction about the fuel tank: 1. Fuel tanks can be divided into two types: open fuel tanks and closed fuel tanks. The fuel tank must have sufficient volume; the suction pipe and return pipe should be inserted below the lowest liquid level to prevent air suction and oil return splashing, which can cause bubbles. 2. In addition to storing oil, the fuel tank in a hydraulic system also plays roles in heat dissipation, separating bubbles from the oil, and precipitating impurities. The fuel tank is equipped with many accessories, such as coolers, heaters, air filters, and liquid level gauges.
8
0
Share

What Causes Car Shaking in D Gear?

Car shaking in D gear indicates that the vibration originates from the transmission, as the gear is in D (Drive) position, which means the power is connected. Here are the detailed explanations: 1. Continuous noticeable shaking: If there is continuous noticeable shaking when in D gear, which improves immediately after shifting out of D gear, it may be due to cracks between the engine, transmission, exhaust pipe, and the chassis or body, or aging of the damping rubber. 2. Intermittent shaking: Intermittent shaking could be caused by a dirty throttle valve or excessive carbon buildup in the intake pipe leading to low idle speed, or it may result from faulty spark plugs and ignition coils causing misfires in the ignition system.
5
0
Share

How to Turn Off the Anti-Skid Function on Ford EcoSport?

Ford EcoSport anti-skid function turning off method: In the car's central control settings, find the ESP option and click to turn it off. The following situations require temporarily turning off ESP: 1. When the vehicle is stuck in mud or off-roading, appropriate wheel slip is needed to help escape and climb, so during extreme off-roading or when stuck, to ensure escape, ESP should be turned off first. 2. When encountering wheel slip while climbing on rainy or snowy days, because the vehicle is starting on snowy or waterlogged roads, especially on slopes, the wheels are prone to slip. At this time, the computer will recognize the wheel slip and limit the engine's output, so ESP should be turned off before attempting again. 3. When snow chains are installed on the vehicle tires, the chains used for driving on snow, because they change the wheel's outer diameter and other reasons, may interfere with the data of certain sensors in the ESP system, causing signal inaccuracy. This affects the normal operation of the ESP system, possibly leading to continuous ESP intervention or fault codes, so ESP should be turned off at this time.
8
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.