Is the speed limit on Guanglong Expressway 100 or 120?

1 Answers
OBeau
07/29/25 5:45pm
Guanglong Expressway has a speed limit of 100 kilometers per hour. Additional information: 1. Expressway speed limits: Expressway speed limits refer to the driving speed on high-speed lanes. Expressways should clearly indicate the driving speed for each lane, with the maximum speed not exceeding 120 kilometers per hour and the minimum speed not lower than 60 kilometers per hour. On expressways, the maximum speed for small passenger vehicles should not exceed 120 kilometers per hour, while other motor vehicles should not exceed 100 kilometers per hour, and motorcycles should not exceed 80 kilometers per hour. 2. Relevant regulations: According to the "Road Traffic Safety Law Implementation Regulations," when encountering low visibility weather conditions such as fog, rain, snow, dust, or hail on expressways, if visibility is less than 200 meters, drivers should turn on fog lights, low beams, marker lights, and front and rear position lights, and the speed should not exceed 60 kilometers per hour, maintaining a distance of more than 100 meters from the vehicle in front in the same lane. If visibility is less than 100 meters, drivers should turn on fog lights, low beams, marker lights, front and rear position lights, and hazard warning flashers, and the speed should not exceed 40 kilometers per hour, maintaining a distance of more than 50 meters from the vehicle in front in the same lane. If visibility is less than 50 meters, drivers should turn on fog lights, low beams, marker lights, front and rear position lights, and hazard warning flashers, and the speed should not exceed 20 kilometers per hour, exiting the expressway at the nearest exit as soon as possible.
Was this review help?
5
4
Share
More Forum Discussions

What are the causes of insufficient cylinder pressure in the Familia II?

The causes of insufficient cylinder pressure in the Familia II are as follows: 1. Excessive wear of the cylinder or piston rings, as well as misalignment, sticking, or breakage of piston rings, leading to insufficient cylinder pressure. Prolonged exposure to high temperatures can cause insufficient elasticity in the piston rings, preventing proper sealing of the piston, which also results in insufficient cylinder pressure. 2. Damage or poor sealing of the cylinder gasket, leading to insufficient cylinder pressure. The cylinder gasket serves to isolate two cylinders independently, and damage to the gasket between adjacent cylinders can cause gas leakage between them, ultimately resulting in low pressure in both adjacent cylinders. 3. Warping of the cylinder head's lower surface, leading to insufficient cylinder pressure. High engine coolant temperature can cause the cylinder head to deform, losing its flatness and resulting in poor cylinder sealing, which manifests as insufficient pressure during cylinder pressure measurement. 4. Poor sealing of the intake and exhaust valves, leading to insufficient cylinder pressure. Erosion of the valve cone surface, bending or breakage of the valve, or improper adjustment of the valve clearance can all cause poor cylinder sealing and insufficient cylinder pressure.
11
3
Share

Is the Great Wall Cannon a four-wheel drive?

The Great Wall Cannon is a four-wheel drive vehicle. The Great Wall Cannon is a pickup truck under the Great Wall brand. This model is equipped with two types of engines: a 2.0-liter turbocharged gasoline engine and a 2.0-liter turbocharged diesel engine. Vehicle Introduction: The Great Wall Cannon series is the flagship model of Great Wall Pickup. It made its debut at the Shanghai Auto Show on April 16, 2019. As a brand-new product series, it is built on a new platform and produced at the new Chongqing factory, targeting the international mainstream market. It is equipped with various practical features such as an intelligent connectivity system, one-button start, keyless entry, electric sunroof, seat heating, vehicle stability system, brake assist, and cruise control. Model Configuration: In terms of power, the entire series is equipped with a 2.0T inline 4-cylinder turbocharged engine, paired with an 8-speed automatic manual transmission. It delivers a maximum power of 140KW, a maximum horsepower of 190PS, and a maximum torque of 360N.m. The maximum power speed ranges from 4000 to 5500 rpm, and the maximum torque speed ranges from 1800 to 3600 rpm. All fuel supply methods are direct injection.
9
0
Share

What to Do When the Car Won't Start After Driving Through Water?

If the car won't start after driving through water, it may be due to the ignition system being affected by moisture or water ingress, causing electrical component failure. It is recommended to dry or air-dry the system before attempting to start the car again. Below are some methods for driving through waterlogged areas: 1. When driving through water, you must follow the principle of 'one test, two slow, three pass.' Enter the water at a slow and steady speed, and avoid stopping while in the water. Do not ease off the throttle; maintain a lower speed to prevent water from rushing in. If the water is not too deep, use a lower gear with slightly more throttle to pass through. 2. During the process of driving through water, keep the steering wheel and throttle steady to ensure the vehicle has sufficient and stable power. Try to complete the crossing in one go, avoiding stopping midway, making sharp turns, or jerking the steering wheel. If you notice the wheels slipping or sinking, do not press the accelerator hard. Instead, with the engine still running, seek assistance from others or another vehicle to help drive out of the waterlogged area.
20
1
Share

What does 102V tire mean?

102V tire has the following meanings: 1. 102 is the load index, indicating that each tire can bear a maximum weight of 850kg. 2. V is the speed rating, representing that each tire can withstand a maximum speed of 240km/h. Here is more information about car tires: 1. Car tires are one of the important components of a vehicle. They directly contact the road surface and work together with the car suspension to absorb the impact during driving, ensuring good ride comfort and smooth driving. They also ensure good adhesion between the wheels and the road, improve the car's traction, braking, and off-road performance, and bear the weight of the vehicle. 2. Checking tire pressure is the most important part of daily tire maintenance. During daily driving, it is essential to develop a good habit of regularly checking tire pressure to eliminate potential safety hazards in the bud.
11
1
Share

How to Replace the Mazda Key Battery?

Mazda key battery replacement method is as follows: 1. Turn the car remote key to the back. 2. Use a flat-head screwdriver to insert it between the key ring and the key side, move the screwdriver along the gap to both sides to gradually widen the gap, and then open the back cover. 3. Remove the old battery and replace it with a new one, paying attention to distinguish the positive and negative poles and not to install the battery backward. 4. Reinstall the back cover. Replacement precautions are as follows: 1. Purchase the original battery for the car key to ensure the voltage and model are the same. 2. Take measures to prevent small parts from falling and getting damaged before prying open the key. 3. After reassembling the electronic key, ensure the buckle is restored to its original position and the mechanical key is locked in place.
9
1
Share

What causes steering wheel vibration when the car reaches 120 km/h?

Reasons for steering wheel vibration when the car reaches 120 km/h are as follows: 1. The wheel is an assembly composed of a tire and a rim. If the mass distribution of each component is uneven, it will cause dynamic imbalance when the wheel rotates at high speed, resulting in noticeable steering wheel vibration. 2. At a speed of 120 km/h, steering wheel vibration may be caused by inconsistent tire pressure. Inconsistent tire pressure can also lead to reduced braking efficiency, difficulty in steering or heavy steering, and prolonged driving under such conditions can reduce tire lifespan, increase the risk of tire blowouts, and raise fuel consumption. 3. Damper failure can also cause steering wheel vibration when the vehicle is driving at high speed. The damper is used to suppress the oscillation from the spring's rebound after absorbing shocks and impacts from the road surface. Once it fails, it can also cause abnormal noises, body vibration, and steering wheel vibration.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.