Is the Sehol Engine Made by Volkswagen?

1 Answers
LaJonathan
07/30/25 3:42am
Sehol's engine is a domestically produced engine manufactured by the Jianghuai Group. Sehol is a new brand established through a collaboration between Jianghuai Automobile and Volkswagen. Therefore, its engine is not from Volkswagen. The engine model used by Sehol is HFC4GC1.6E, with a maximum horsepower of 184, a maximum power output of 135KW, a maximum power speed of 5500rpm, and a peak torque of 300N.m. For daily maintenance of the Sehol engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment in the intake and exhaust systems and usage conditions; for diesel engines, choose CB_CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine issues. To avoid malfunctions, change the oil regularly according to usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, it may rupture the filter element or open the safety valve, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. In small amounts, it remains suspended in the oil; in large amounts, it precipitates, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
Was this review help?
19
1
Share
More Forum Discussions

What is a Business Vehicle?

Business vehicles, also known as multi-purpose vehicles (MPVs), combine the functions of sedans, station wagons, and vans. Each seat in the vehicle can be adjusted and reconfigured in various ways. For example, the backrest of the middle row seats can be folded down to form a table, and the front seats can rotate 180 degrees. Originally, business vehicles referred to small passenger vans. Later, Renault of France improved this model by introducing the concept of foldable second and third-row seats. Business vehicles emphasize versatility, integrating the features of sedans, station wagons, and commercial vehicles. The first multi-purpose vehicle (MPV) was introduced in 1983. Advantages of Business Vehicles: Spacious interiors—7-seater business vehicles feature large space designs, often incorporating face-to-face conference table setups, allowing business professionals to conduct meetings directly inside the vehicle; high safety standards—7-seater business vehicles are equipped with full-range seat belts, standard safety headrests, and front and rear safety brakes.
20
1
Share

Why does the BMW Mini N16 engine burn oil?

There are reasons why the BMW Mini N16 engine burns oil. Environmental factors: Due to different driving conditions, domestic fuel quality and road conditions can easily lead to carbon deposits, causing the piston rings to stick and lose their oil-scraping performance. Engine factors: Blocked oil return holes prevent oil from returning normally to the crankcase; wear between the cylinder walls and pistons leads to excessive gaps; corrosion and aging of valve seals and crankshaft seals cause oil leakage. If sealing components fail, the working surfaces cannot be lubricated, resulting in severe wear. This can also damage other functional components, rendering them inoperable, or cause oil leakage due to corrosion and aging of valve seals and crankshaft seals. Solutions: Take the car to a 4S shop for engine repair, including replacing the piston rings and valve seals. Regularly inspect the engine for internal issues. If the engine emits blue smoke during high-load operations like idling starts, it should be sent for maintenance. Additionally, using high-quality engine oil ensures good operational efficiency and reduces such occurrences.
1
4
Share

What material is the Bentley bumper made of?

Bentley bumpers are made of plastic. Bumper Introduction: The material is plastic, commonly referred to as a plastic bumper. The outer panel and cushioning material are made of plastic, while the crossbeam is formed by stamping cold-rolled thin plates of about 1.5mm thickness into a U-shaped channel. The outer panel and cushioning material are attached to the crossbeam, which is then screw-connected to the frame longitudinal beams. These plastic bumpers primarily use two types of materials: polyester-based and polypropylene-based, manufactured through injection molding. Bumper Function: Bumpers provide cushioning during low-speed collisions, protecting the front and rear body of the vehicle. They also offer some protection for pedestrians in accidents involving them. Additionally, bumpers serve a decorative purpose, being an important component in enhancing the vehicle's exterior appearance. They help reduce injuries to passengers during side-impact collisions and strengthen the door's resistance to impact forces. Bumper Maintenance: Regularly wipe with a damp cloth and inspect for any scratches or partial damage to prevent accidents.
14
5
Share

How often should a Jetta be serviced with Shell Helix HX7?

Jetta using Shell Helix HX7 can be replaced every six months. Replacement cycle: Change the engine oil every 5,000 to 10,000 kilometers. If the car is used infrequently and it takes several years to reach 10,000 kilometers, then replace it based on time, which can be every six months. Reason: If the oil is not changed for a long time, it will deteriorate. Engine oil has its own replacement cycle. The degradation of engine oil is actually affected by oxidation, and the speed of degradation is determined by the rate of oxidation. Regular oil changes are very necessary, as the oxidized substances in the oil will be expelled from the engine, creating a good working environment for the engine. Maintenance: During maintenance, the gasoline filter and air filter can be removed and cleaned with compressed air if they are not dirty. Additionally, replace the spark plugs every 30,000 kilometers. Pay attention to whether the gear oil has water ingress; if it does, replace it in advance. The timing belt and timing belt tensioner should be replaced every 80,000 kilometers for 2V models and every 60,000 kilometers for 5V models.
12
5
Share

Does the Automotive Three-Way Catalytic Converter Need Cleaning?

The automotive three-way catalytic converter needs cleaning when symptoms such as difficulty starting, weak acceleration, inability to reach higher speeds, white smoke from the intake manifold, or even backfiring occur. Additional information on the three-way catalytic converter: 1. Reasons for cleaning the three-way catalytic converter: Under normal circumstances, the minimum service life of a three-way catalytic converter is approximately 130,000 km. With proper use, it generally does not fail. The common issues encountered are blockages, excessive carbon deposits, poor oil quality, severe oil burning, and prolonged driving in congested roads, all of which can cause the three-way catalytic converter to clog. In such cases, cleaning the three-way catalytic converter is usually sufficient. 2. Timing for cleaning the three-way catalytic converter: It can be based on the maintenance manual or the actual condition of each vehicle. The specific judgment is that once the three-way catalytic converter is clogged, the engine's performance will severely deteriorate, necessitating cleaning. If the vehicle has exceeded 30,000 km without exhibiting the above issues, cleaning may not be necessary.
16
4
Share

What is the Difference Between the Ex-factory Price and the On-the-road Price of a New Car?

The difference between the ex-factory price and the on-the-road price of a new car is: 1. Definition: The ex-factory price refers to the price of the car alone, while the on-the-road price includes (the ex-factory price, car insurance, and taxes). You can also understand the on-the-road price as the total cost of your purchased vehicle plus purchase tax, insurance, registration, and other fees, which is the price you pay to drive the car on the road. 2. Ex-factory price: The price set by the 4S store based on the manufacturer's suggested retail price (MSRP) and market conditions. 3. On-the-road price: The total cost required for the vehicle to be legally driven on the road. The on-the-road price is the final transaction price, meaning that once you have completed all the legal procedures and can drive the car on the road, the sum of all the costs associated with the vehicle is the on-the-road price.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.