Is the Roewe e950 a New Energy Vehicle Model?

Why Does the Car Air Conditioner Only Cool When the Car is Moving?

There are several reasons why a car air conditioner only cools when the vehicle is in motion: 1. Refrigerant: Insufficient refrigerant. 2. Blockage: Expansion valve blockage or evaporator coil blockage. 3. Condenser: Condenser coil blockage or excessively high system temperature, resulting in poor cooling performance. 4. Air conditioning system: Leakage in the air conditioning system pipelines. 5. Pressure: Insufficient pressure from the air conditioning compressor. 6. Short circuit: Blown air conditioning fuse, damaged wiring, short circuit, or poor connector contact. The functions of a car air conditioner are as follows: 1. Cooling: Achieves cooling effect through the continuous phase change cycle of the refrigerant. 2. Deodorizing: Removes dust, odors, smoke, and toxic gases from the air inside the car, freshening the interior air. It also humidifies the air inside the car, increasing the relative humidity of the interior air.

6

3

Share

What to Do When the Car Seat Belt Doesn't Retract Properly?

Solutions for when the car seat belt doesn't retract properly are as follows: To check if the seat belt is functioning, pull it down quickly and forcefully to see if it locks. If it locks, the seat belt can still serve its restraining function. However, if it doesn't lock when pulled quickly and forcefully, the seat belt is no longer effective and should be replaced immediately at a 4S shop. Introduction to Car Seat Belts: 1. Function: The car seat belt is a safety device designed to restrain occupants during a collision, preventing secondary impacts with the steering wheel, dashboard, etc., or avoiding injuries from being thrown out of the vehicle. 2. Overview: The car seat belt, also known as a seat safety belt, is a type of occupant restraint system. It is widely recognized as the most cost-effective and efficient safety device in vehicles, and its installation is mandatory in many countries.

2

1

Share

Which is the largest used car trading market in Kunshan?

The largest used car trading market in Kunshan is Kunshan Huafeng Used Car Trading Market. Located on the east side of Huangpu River Road, Zhoushi Town, Kunshan City, adjacent to Provincial Highway 339, it is a key project of Kunshan City with strong government support, covering a total area of 84,337.1 square meters. Below is an introduction to Huafeng Used Car Trading Market: 1. Scale: The total area is 84,337.1 square meters, with the first phase covering approximately 28,000 square meters and a total investment of 90 million yuan. The 28,000-square-meter area consists of 10 buildings divided into 5 major service zones. The second phase features 33~55 square meters prime shops and a 60-meter landmark building—a hotel apartment complex, creating a wealth event integrating the automotive industry and commercial real estate. 2. Overview: It is the only used car trading market in the city, equipped with 80 intermediary trading offices and nearly a thousand parking spaces. Situated in the core area of Kunshan Commercial City, it is surrounded by supporting facilities such as Metro Supermarket, Red Star Macalline, Mercedes-Benz 4S store, and Ganglong Decoration City. In 2009, Kunshan's used car transactions achieved a 38% growth rate, and in 2010, the total transaction volume of used motor vehicles in Kunshan City is expected to reach around 1.3 billion yuan.

9

0

Share

What Type of Vehicle is a Light-duty Flatbed Truck?

Light-duty flatbed trucks fall under the category of small cargo vehicles. Here is some relevant information: 1. Classification: Cargo vehicles can be divided into four types: heavy-duty, medium-duty, light-duty, and mini. Heavy-duty and medium-duty cargo vehicles are issued large truck license plates, i.e., large vehicles (commonly known as yellow plates), while light-duty and mini cargo vehicles are issued small truck license plates, i.e., small vehicles (commonly known as blue plates). 2. Appearance: Light-duty flatbed trucks refer to vehicles with high railings or fully enclosed structures, typically with railings 160-200 cm high; whereas small cargo vehicles refer to ordinary trucks with only 30-50 cm high railings and no additional structures on top.

8

0

Share

How to Reset Audi Tire Pressure?

Audi tire pressure reset method: First, turn on the ignition, press and hold the tire pressure monitoring reset button until you hear a "beep" sound, then release it. The tire pressure monitoring system will store the current normal tire pressure data, automatically clear the previous data, and finally, the dashboard warning light will turn off, completing the tire pressure reset. Solutions for insufficient tire pressure: If no damage is visible, simply inflate the tire to the normal pressure and reset the tire pressure system; If a puncture is found upon inspection, drive to a tire shop promptly for repair, then reinflate the tire; If the low tire pressure warning reappears after inflation without any punctures, it may be due to air leakage caused by a deformed wheel rim. It is recommended to check the wheel rim and replace it if necessary. Hazards of low tire pressure: Increased friction coefficient with the road surface, leading to higher fuel consumption; Causes heavy steering and makes the vehicle prone to deviation, posing risks to driving safety.

6

4

Share

Can You Still Drive When the Mercedes Brake Pad Warning Light Comes On?

You should not continue driving when the Mercedes brake pad warning light comes on. Here are the relevant details: 1. Classification of Brake Pads: Automotive brake pads can be categorized by type into those used for disc brakes, brake shoes for drum brakes, and linings for large trucks. Brake pads are mainly divided into the following categories: metal brake pads and carbon-ceramic brake pads. Metal brake pads are further divided into low-metallic and semi-metallic brake pads, with ceramic brake pads classified under low-metallic. Carbon-ceramic brake pads are used in conjunction with carbon-ceramic brake discs. 2. Working Principle: The working principle of braking primarily relies on friction. By utilizing the friction between the brake pads and the brake disc (or drum), as well as between the tires and the ground, the kinetic energy of the moving vehicle is converted into thermal energy through friction, bringing the car to a stop. A good and efficient braking system must provide stable, sufficient, and controllable braking force, along with excellent hydraulic transmission and heat dissipation capabilities. This ensures that the force applied by the driver on the brake pedal is effectively transmitted to the master cylinder and individual wheel cylinders, while avoiding hydraulic failure and brake fade caused by excessive heat. If the brake pad warning light comes on, it is crucial to replace them promptly, as it is a matter of life safety.

12

5

Share

Is the Roewe e950 a New Energy Vehicle Model?

Why Does the Car Air Conditioner Only Cool When the Car is Moving?

What to Do When the Car Seat Belt Doesn't Retract Properly?

Which is the largest used car trading market in Kunshan?

What Type of Vehicle is a Light-duty Flatbed Truck?

How to Reset Audi Tire Pressure?

Can You Still Drive When the Mercedes Brake Pad Warning Light Comes On?

Is it easy to remove a car film that has been applied for a week?

What brand is Ora?

Where is the position and direction for the car sticker gecko?

Is It Serious When a Car Makes a Thud Sound After Driving Off a Step?