Is the owner's ID card required for motorcycle annual inspection?

What are the common faults of Citroen C5?

Common faults include engine failure, fuel injection system failure, ECU failure, etc. The causes of these faults are as follows: 1. Starting system failure prevents the engine from turning or turning too slowly: insufficient battery charge, loose or severely oxidized electrode terminal clamps; blown main circuit fuse; ignition switch failure; starter failure; open circuit in the starting line or poor contact of the line connector. 2. Ignition system failure: poor performance of the ignition coil, resulting in weak or no high-voltage spark; ignition device failure; incorrect ignition timing. 3. Fuel injection system failure: no fuel in the tank; fuel pump not working or low pumping pressure; fuel pipe leakage or deformation; open circuit relay disconnection; poor performance of the fuel pressure regulator; excessively dirty fuel filter. 4. Intake system failure: idle control valve or its control line failure; idle control valve air pipe rupture or joint air leakage; air flow meter failure.

13

4

Share

What is the body structure of the Exeed Landmark?

Introduction to the body structure of the Exeed Landmark is as follows: 1. In terms of safety architecture design: Built on the M3X Mars architecture, the Exeed Landmark adopts an integrated cage-type body with a high-strength steel application rate of up to 78%. The B-pillar has a tensile strength of 1500MPa. Additionally, the Exeed Landmark features a subframe detachment technology typically found in luxury brands, which allows the body to bounce and slide away during frontal or small-angle collisions, improving collision energy absorption efficiency and reducing collision damage. 2. The Exeed Landmark is equipped with the most comprehensive and advanced active safety system currently available in the market: Its autonomous driving capability reaches L2.5 level. It also ensures the security of the vehicle's internet connection through identity authentication, link security, data signature/encrypted transmission, and software security, safeguarding user information security. Furthermore, it provides CN95-level protection, ensuring users breathe clean and safe air inside the vehicle, comprehensively protecting their travel health and safety.

13

2

Share

What causes the vibration of the new Sylphy in D gear when stationary?

If the transmission was previously disconnected in neutral and then connected after shifting to D gear, slight vibration is a normal phenomenon; if the vibration is severe, it may be due to spark plug issues, and it is recommended to have it checked at a service center. The following is an introduction to the new Sylphy: 1. Configuration: The new Sylphy is a main sales contributor for Dongfeng Nissan. The central control features a 7-inch touchscreen + basic button design, integrating Carplay functionality, and systems such as Bluetooth calls and multimedia can also be operated through it. The newly added 2019 Intelligent Connect version is equipped with Dongfeng Nissan's self-developed "Intelligent Connect+" system, which includes intelligent voice control, full-time in-car navigation, remote real-time monitoring, 24-hour entertainment, in-car Wi-Fi hotspot, and worry-free data usage. 2. Powertrain: The new Sylphy adopts a combination of a 1.6L naturally aspirated engine and a CVT continuously variable transmission, with a maximum power of 93kW (126PS) and a maximum torque of 154N·m. There is also a 1.8L naturally aspirated engine option, with a maximum power of 102kW (139PS) and a maximum torque of 174N·m/3600rpm, also paired with a CVT continuously variable transmission.

8

0

Share

What does Chevrolet Code 82 mean?

Chevrolet Cavalier's code 82 indicates a faulty oil pressure sensor, which needs to be replaced at a 4S shop as soon as possible. Here is an introduction to the oil pressure sensor: 1. Oil Pressure Sensor: Installed on the engine's main oil passage, when the engine is running, the pressure measuring device detects the oil pressure, converts the pressure signal into an electrical signal, and sends it to the signal processing circuit. After voltage and current amplification, the amplified pressure signal is connected to the oil pressure gauge via a signal line. 2. Changing the Oil Pressure Gauge: Indicates the ratio of current passing through the two internal coils, thereby displaying the engine's oil pressure. The amplified pressure signal is also compared with the set alarm voltage in the alarm circuit. When it falls below the alarm voltage, the alarm circuit outputs an alarm signal and lights up the alarm lamp via the alarm line. 3. Wiring Method of Electronic Oil Pressure Sensor: Fully consistent with traditional mechanical sensors, it can replace mechanical pressure sensors and directly connect to the vehicle's oil pressure gauge and low-pressure alarm lamp, indicating the diesel engine's oil pressure and providing low-pressure alarm signals.

12

0

Share

What Causes Abnormal Noise in Yamaha Engines?

Abnormal noise in Yamaha engines is caused by drawbacks of direct fuel injection technology, operation of the carbon canister solenoid valve, and cold starts of the vehicle. Drawbacks of direct fuel injection technology: Direct injection engines tend to be noisier because the fuel injection pressure in these engines is over ten times higher than in conventional engines. The vibration produced by the fuel injectors during high-pressure injection can be particularly noticeable as abnormal noise during quiet or low-speed driving. Operation of the carbon canister solenoid valve: The carbon canister solenoid valve opens when the engine starts, allowing the gasoline vapors adsorbed in the carbon canister, along with air, to enter the cylinders for combustion. This component can also produce a distinct abnormal noise during operation. Vehicle cold starts: During a cold start, the oil pump has not yet fully built up oil pressure, resulting in insufficient lubrication for various components. Normally, the abnormal noise will disappear after the engine has been running for a while.

12

3

Share

Are all 2003 Polo models imported?

All 2003 Polo models are imported. Here is an introduction about the Polo car: 1. Exterior: The exterior is sporty and stylish, especially the headlights. The LED side turn signals are also a relatively mainstream configuration recently. 2. Interior: The interior is rough, which is a common issue with compact cars, but the new Cross-POLO has seen significant improvements. 3. Handling: It offers handling performance that other vehicles in the same class cannot provide. Whether driving at high speeds or navigating through urban areas at low speeds, the POLO maintains excellent stability and operability. There is no noticeable feeling of instability at high speeds, and the steering remains precise. During low-speed driving, accelerating and decelerating, as well as maneuvering up and down, are all handled with ease, bringing the POLO's handling to a new level.

14

5

Share

Is the owner's ID card required for motorcycle annual inspection?

What are the common faults of Citroen C5?

What is the body structure of the Exeed Landmark?

What causes the vibration of the new Sylphy in D gear when stationary?

What does Chevrolet Code 82 mean?

What Causes Abnormal Noise in Yamaha Engines?

Are all 2003 Polo models imported?

What does Xiaopeng LCC mean?

Where is the Geely Xingyue produced?

What Causes the Odor in BMW 116i Cabin?

What is the actual fuel consumption of the Transit Diesel version?