Is the overtaking speed requirement in Subject 3 above 30km/h?

1 Answers
DiEliana
07/29/25 10:57pm
There is no specific speed requirement for overtaking in Subject 3. Generally, maintain a speed of around 35 km/h in third gear. Below are the key points to note during the overtaking process in the Subject 3 test: 1. Details: When performing the overtaking maneuver in Subject 3, there is a crucial detail of looking back over your shoulder. Failing to do so will result in failure. 2. Timing: When the candidate hears the voice prompt to start the overtaking maneuver, they should immediately turn on the left turn signal. After confirming there are no vehicles approaching from the left rear, decisively change lanes to the left, ensuring proper timing. 3. Turn signal: The turn signal must be activated for at least 3 seconds. If it's less than 3 seconds, it may be judged as not using the turn signal.
Was this review help?
16
1
Share
More Forum Discussions

How to Check Vehicle Inspection Time?

Methods to check vehicle inspection time: Look at the duplicate of the vehicle license. For example, if the "Inspection Valid Until April 2019" is indicated on the duplicate of the vehicle license, then the annual inspection date is three months before the inspection validity period (including the current month), meaning the annual inspection date is from February to April 2019. The vehicle annual inspection date is calculated by month, and processing the vehicle annual inspection in the last full month of the validity period is not considered overdue. Annual inspection is a mandatory test for every vehicle that has obtained an official license plate and vehicle license, which means an annual physical examination of the vehicle according to the safety technical conditions for motor vehicle operation. Vehicle annual inspection can promptly eliminate potential safety hazards, urge the strengthening of vehicle maintenance, and reduce the occurrence of traffic accidents.
13
4
Share

How Much Horsepower Does a Motorcycle Have?

Generally, the power of a motorcycle is around 6–7 kW, equivalent to 8–9.5 horsepower. Additional Information: There is no specific standard for motorcycle horsepower, as it depends on how the bike is tuned. A well-tuned 150cc bike can reach speeds of 200 km/h, and the largest displacement motorcycles now reach up to 1600cc. Horsepower was originally defined by the French and Germans, but since the horses used to measure horsepower were smaller than average, an engine with 50 horsepower should not be imagined as 50 horses pulling the motorcycle—35 horses would be a more accurate comparison. The unit of horsepower is represented by (ps), a symbol first used by the Germans and still in use today.
2
2
Share

What to Do When There's Abnormal Noise During Low-Speed Braking?

Reasons for abnormal noise during low-speed braking include: 1. Overly worn brake pads: The exposed fixing points of the friction material rub against the brake disc or brake drum, causing abnormal noise. Solution: Replace the brake pads. 2. Poor contact surface: After replacing the brake pads, improper contact with the brake disc or drum leads to point or line contact, resulting in abnormal noise. Solution: Perform a break-in period for the vehicle. 3. Water exposure: Brakes may produce abnormal noise after the car has been through water. Solution: Handle according to water drainage, remove accumulated water, and replace the corresponding parts. 4. Wear: Excessive wear on the brake disc or brake drum. Solution: Replace the brake disc or brake drum.
19
1
Share

How to Use the Electronic Parking Brake in an Automatic Transmission Car?

Automatic transmission car electronic parking brake usage method: The operation is relatively simple. When parking, just step on the brake pedal, shift the gear into P, and then lift the electronic parking brake button; conversely, when starting, press the button to release the parking brake. The more advanced feature of the electronic parking brake is that when the driver fastens the seatbelt and prepares to start, stepping on the accelerator allows the car to move, as the electronic parking brake automatically releases completely, greatly reducing the operation time for vehicle start-up. However, this function is currently only available on some models, and most models still require manually pressing the button to release the electronic parking brake.
14
5
Share

What to do if the Polo trunk cannot be opened?

If the Polo trunk cannot be opened, you can go to a 4S shop to check whether it is a computer lock problem or other issues. Method to open the Polo trunk: The Polo has a central locking system for the entire vehicle, and there is no trunk button inside the car. The central door lock button on the driver's door can open the trunk. The central lock controls the doors, fuel tank, and trunk. Outside the car, press the unlock button on the remote control, and check if the trunk is separately locked. If it is locked, you must use the key to open it. In terms of body dimensions, the Polo has a length of 4053mm, a width of 1740mm, a height of 1449mm, and a wheelbase of 2564mm.
13
0
Share

How to Open the Nissan Sylphy Key Fob?

Nissan Sylphy key fob disassembly method: 1. Remove the mechanical key; 2. Use a flat-head screwdriver to pry open a small gap from the side seam of the key fob, then gradually separate along the opening; 3. Insert the tool into the central seam of the remote, gently squeeze while applying slight outward pressure to open it. The Sylphy measures 4641mm in length, 1815mm in width, and 1450mm in height, with a wheelbase of 2712mm. It's a 4-door 5-seater sedan equipped with a 1.6L L4 naturally aspirated engine, delivering maximum power of 135PS, peak torque of 159Nm, and rated output of 99kW.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.