Is the Ora Good Cat 2021 Model a New Energy Vehicle?

How to Remove Iron Particles from a Car?

Methods to remove iron particles from a car: Minor iron particles can be removed using a clay bar, which must be kept lubricated with water during use. For severe cases, an iron particle remover can be used; it quickly decomposes iron particles on the car's paint and rims. After the reaction changes color, rinse it off with water. Below is an introduction to the hazards of iron particles on cars: Iron particles on the paint surface will adhere to the car's surface as water evaporates, turning into yellowish-brown rust spots after oxidation. These particles will continuously spread and oxidize the surrounding paint. Eventually, they can penetrate the paint surface, reaching the primer to directly oxidize the metal, or due to high speed, they may embed into the paint or soften and integrate into it under the influence of high temperatures and heat emitted by the engine.

6

3

Share

Why Was the New Baojun RM-5 Discontinued?

Baojun RM5 faced significant issues with its engine, with engine failures and transmission jerks being the main complaints from actual owners. In such a fiercely competitive market, it struggled to survive, and its sales fell far short of the expected targets, leading to the decision to discontinue production to minimize losses. Below are the relevant details about the New Baojun RM5: 1. Introduction One: The New Baojun RM5 is a compact MPV with dimensions of 4705mm in length, 1806mm in width, and 1615mm in height, and a wheelbase of 2750mm. It is equipped with two types of engines: a 1.5L turbocharged engine and a 1.5L naturally aspirated engine. 2. Introduction Two: The 1.5L turbocharged engine delivers a maximum power of 108kW at 5200 rpm and a maximum torque of 250Nm between 2200 and 3400 rpm. This engine features multi-point fuel injection technology and uses an aluminum cylinder head with a cast iron cylinder block. It is paired with either a 6-speed manual transmission or a CVT. 3. Introduction Three: The 1.5L naturally aspirated engine produces a maximum power of 73kW at 5800 rpm and a maximum torque of 143Nm between 3400 and 4400 rpm. This engine also employs multi-point fuel injection technology and uses an aluminum cylinder head with a cast iron cylinder block. It is matched with either a 6-speed manual transmission or a CVT. 4. Introduction Four: The New Baojun RM5 features a MacPherson independent front suspension and a torsion beam non-independent rear suspension. The use of a torsion beam rear suspension helps to maximize rear passenger space and trunk capacity, which are crucial for an MPV.

1

2

Share

How are new energy vehicles subsidized?

According to Article 9 of the "New Energy Vehicle Subsidy Standards", the subsidy amount is determined based on the energy capacity of the power battery pack. For eligible new energy vehicles, a subsidy of 3,000 yuan per kilowatt-hour is provided, with plug-in hybrid passenger vehicles receiving a maximum subsidy of 50,000 yuan per vehicle, and pure electric passenger vehicles receiving a maximum subsidy of 60,000 yuan per vehicle. The following is an introduction to new energy vehicles: 1. New energy vehicles refer to vehicles that use unconventional vehicle fuels as power sources, integrating advanced technologies in vehicle power control and driving systems, resulting in vehicles with advanced technical principles, new technologies, and new structures. Unconventional vehicle fuels refer to fuels other than gasoline and diesel. 2. New energy vehicles include four major types: hybrid electric vehicles, pure electric vehicles, fuel cell electric vehicles, and other new energy vehicles.

20

1

Share

What is the detection method for electronic throttle pedals?

Detection method for electronic throttle pedals: 1. There are two ICs inside the electronic throttle pedal, referred to as the main pedal sensor and the secondary pedal sensor. 2. The reference voltage should be the state voltage reference value provided by the original manufacturer's data. When the pedal is not pressed, the reference voltage value for the main IC should be 800mV, and when fully pressed, it should be around 4900mV. 3. If the throttle pedal data does not match the reference voltage, being either too high or too low indicates a fault in the electronic throttle pedal. The following is an introduction to electronic throttle pedals: As a key component of the electronic throttle control system, the performance of the electronic throttle pedal is not only related to the vehicle's power performance, comfort, fuel economy, and other performance evaluation indicators but also to the vehicle's driving safety.

19

2

Share

Will installing caliper covers affect heat dissipation?

Installing caliper covers will significantly affect heat dissipation. Since the heat generated by prolonged caliper operation cannot dissipate, it will impact the vehicle's braking performance. As caliper covers come in fixed sizes, trimming is often required during installation, and adhesive is used for fixation. If low-quality adhesive is used, the caliper cover may easily detach, posing a serious safety hazard. Below is an introduction to brake calipers: 1. Genuine brake calipers are expensive. Some car enthusiasts install caliper covers purely for visual appeal, but these serve only decorative purposes and offer no practical function. 2. Caliper covers can hinder the heat dissipation of brake calipers and may even break or fall off during driving, which is highly unsafe. Therefore, it is strongly advised that car enthusiasts avoid using caliper covers. 3. Many car enthusiasts modify calipers not for visual effects but to enhance braking power. If the goal is to improve braking performance, upgrading the brake pads should be the first step, as a high-quality set of brake pads can significantly increase braking force.

10

5

Share

What level of maintenance does tire disassembly, inspection, and rotation belong to?

Tire disassembly, inspection, and rotation belong to secondary maintenance. Below is an introduction to tire rotation: 1. Tire rotation is a maintenance measure to extend the service life of the vehicle's tires. Its main purpose is to prevent uneven wear on the car tires over time, which could affect driving safety. 2. The primary reason for uneven tire wear is that tires are divided into front drive wheels and rear non-drive wheels, which bear different forces and thus experience different degrees of wear. Additionally, during braking, the car does not distribute the braking force as evenly as one might think. Generally, the front wheels play the main role in deceleration, so the front tires usually wear out more severely than the rear tires.

8

1

Share

Is the Ora Good Cat 2021 Model a New Energy Vehicle?

How to Remove Iron Particles from a Car?

Why Was the New Baojun RM-5 Discontinued?

How are new energy vehicles subsidized?

What is the detection method for electronic throttle pedals?

Will installing caliper covers affect heat dissipation?

What level of maintenance does tire disassembly, inspection, and rotation belong to?

What is the method for resetting the tire pressure monitoring system?

How to Clean Fabric Seats?

How to Define an Off-Road Vehicle?

What to Do If You Forget to Bring Your Driver's License During a Traffic Check?