Is the Nissan Teana a B-segment car?

How to Change Engine Oil and Oil Filter?

Here are the steps to change engine oil and oil filter: 1. Drain the used oil: Place the drain pan under the oil drain plug and tilt it slightly backward. Use a wrench to turn the drain plug counterclockwise until it rotates easily. Then remove the plug by hand. Be careful as the oil inside may flow out quickly and could be hot. After draining, clean the drain plug and reinstall it. 2. Replace the oil filter: Use a wrench to loosen the oil filter counterclockwise and remove it, being careful not to touch the hot exhaust pipe. The filter may be full of oil and feel heavy, so remove it carefully away from the engine and pour the oil into the drain pan. Then install the new filter. 3. Add new oil: Locate the oil filler cap marked "Oil" on top of the engine. Open this cap and pour in the specified amount of oil. Check the dipstick to confirm the oil level is correct. Then replace the cap and wipe off any spilled oil.

16

1

Share

What Causes High Carbon Monoxide Levels in Cars?

Excessive carbon monoxide in car exhaust is generally caused by incomplete combustion in the engine. Since gasoline contains a large amount of carbon, it is normally oxidized into carbon dioxide during proper combustion. However, under oxygen-deficient conditions, it is oxidized into carbon monoxide. The reasons for incomplete combustion include the following: 1. Cold engine testing: At low temperatures, gasoline evaporation is poor, so the exhaust emissions differ significantly between a cold start and a fully warmed-up engine. National standards specify different exhaust emission indicators for these two conditions, and annual inspections measure the exhaust quality of a fully warmed-up engine. 2. Fuel injector leakage: If the fuel injector does not close tightly, gasoline may slowly seep out under pressure, leading to excessive fuel supply. Common causes include injector aging, carbon buildup, or impurities in the gasoline affecting the injector's closure. 3. Worn spark plugs: Aging spark plugs can reduce ignition energy, potentially failing to ignite the air-fuel mixture, thereby increasing the cylinder misfire rate. A misfire occurs when the spark plug fails to ignite the mixture during combustion, causing the unburned mixture to be expelled directly, resulting in failed emissions. 4. Faulty oxygen sensor: The oxygen sensor detects the oxygen content in the exhaust, and the ECU adjusts the air-fuel mixture concentration based on its signal. A malfunctioning oxygen sensor can cause the mixture to become too rich or too lean, affecting exhaust emissions. 5. Failed catalytic converter: Under high-temperature exhaust heating, the catalytic converter reaches very high temperatures, converting harmful substances in the exhaust into harmless compounds through oxidation-reduction reactions. A damaged catalytic converter will worsen exhaust emissions.

2

Share

What are the techniques for braking?

Here are some braking techniques: 1. Emergency braking: Some vehicles do not have ABS systems, so it is not recommended to fully press the brake pedal at once. Instead, press the brake pedal twice in succession to prevent wheel lock-up, which could lead to skidding and loss of steering control. 2. Braking in rainy conditions: When driving on wet roads, avoid slamming the brake pedal or making sudden steering movements. After passing through a waterlogged area, it's best to gently press the brake pedal twice to utilize inertia and friction to remove water from the brake discs, preventing brake failure during sudden stops. 3. Braking while following another vehicle: When following another car, the main purpose of braking is to maintain a safe distance. Therefore, gently press the brake pedal while keeping an eye not only on the braking of the car in front but also on the movements of the vehicles ahead of it. If you notice the car in front braking, place your foot on the brake pedal in advance to prepare for sudden stops. 4. Avoid continuous braking when stopping: Continuously pressing the brake pedal until the vehicle comes to a complete stop can cause a significant impact. The technique is to release the brake pedal once just before the vehicle stops completely, then gently tap the brake pedal again until the vehicle comes to a full stop.

20

1

Share

How to Add Coolant to a BMW?

Open the hood of the BMW, locate the coolant reservoir on the left side of the engine compartment, and open the filler cap to add coolant. Precautions for adding coolant to a BMW are as follows: 1. Do not open the cooling system when the BMW engine is running at high temperatures, as it may cause burns due to coolant spraying out. 2. Only use the appropriate coolant; otherwise, it may damage the engine. 3. After topping up, ensure the antifreeze cap is securely closed. 4. The correct coolant level is crucial for the trouble-free operation of the cooling system, so check the coolant level regularly. 5. After adding coolant, start the engine and turn on the air conditioning system to check and confirm that the radiator cooling fan is working, and inspect the radiator or hoses for any coolant leaks.

14

0

Share

Is the Chevrolet Malibu Still on Sale?

The Chevrolet Malibu has been discontinued. Here is some extended information about the Chevrolet Malibu: 1. As Chevrolet's global mid-to-high-end flagship sedan, the Malibu first entered the Chinese automotive market in 2012. 2. The Malibu is positioned as a mid-size car, and this model also offered multiple variants for consumers to choose from. 3. The main reason for its discontinuation is that, in the face of a highly competitive automotive market, the Malibu lost its edge. Compared to other joint-venture mid-size cars in the market, the Malibu lagged behind in both interior space and feature offerings. 4. The car's exterior design still followed the brand's family design philosophy and did not undergo a comprehensive upgrade. With the continuous advancement of automotive production technology, consumer expectations for car aesthetics and functionality have grown. Without upgrades, older models naturally become obsolete in the market.

14

0

Share

What are the color options for the Equinox?

The Equinox comes in six body colors: Ice White, Galaxy Silver, Volcanic Red, Canyon Gray, Midnight Black, and Cold Rock Gray. Here is more information about the Equinox: 1. The Equinox is a midsize SUV under the Chevrolet brand, equipped with two engine options: a 1.5L turbocharged engine and a 2.0L turbocharged engine. 2. The 1.5L turbocharged engine delivers 169 horsepower and a maximum torque of 250 Nm. This engine reaches its maximum power at 5,600 rpm and its peak torque between 1,700 and 4,000 rpm. It features direct fuel injection and an aluminum cylinder head and block, paired with a 6-speed automatic transmission. 3. The 2.0L turbocharged engine produces 260 horsepower and a maximum torque of 353 Nm. It achieves maximum power at 5,500 rpm and peak torque between 2,000 and 5,300 rpm. This engine also features direct fuel injection and an aluminum cylinder head and block, paired with an 8-speed automatic transmission.

4

1

Share

Is the Nissan Teana a B-segment car?

How to Change Engine Oil and Oil Filter?

What Causes High Carbon Monoxide Levels in Cars?

What are the techniques for braking?

How to Add Coolant to a BMW?

Is the Chevrolet Malibu Still on Sale?

What are the color options for the Equinox?

How often should the power steering fluid be changed in a Lavida?

What brand is Lynk & Co?

Are 175 Tires and 165 Tires Interchangeable?

How to adjust the time on a Volkswagen?