Is the Mercedes-Benz C260 compliant with China VI emission standards?

Why is the boost pressure too low in BMW N54 engine?

Engine boost pressure too low alarm, it is recommended to conduct a smoke test to check for air leaks in the pipelines, whether the thrust ventilation valve is functioning normally, and if the vacuum system control is operating correctly. Remove the oxygen sensor to inspect if the three-way catalytic converter is clogged. If all the above are ruled out as normal, it is advised to replace the turbocharger. Specific reasons: Boost pressure sensor failure: Generally, the boost pressure sensor and intake air temperature sensor are integrated and installed on the boost air pipe, providing the DME with boost pressure and boost air temperature information. Vacuum supply device malfunction: The vacuum pump is damaged, or there is an air leak in the vacuum supply device pipeline. Wastegate valve sticking or leaking: Mainly caused by poor sealing leading to air leaks, especially at the air duct connection positions before and after the turbocharger intercooler. Improper installation can easily cause poor sealing, or aging and cracking of the sealing rings, resulting in air leaks. Exhaust gas turbocharger itself malfunctioning: The turbocharger itself is damaged and cannot achieve the boosting effect, such as turbine sticking, which is generally caused by poor lubrication or cooling of the turbocharger. Intake pipeline leaks: Fuel tank ventilation system failure or leaks in the pipelines leading to the intake system, and crankcase forced ventilation system failure, etc. Exhaust back pressure too high: For example, a clogged three-way catalytic converter obstructs exhaust gas discharge, leading to excessively high exhaust pipe back pressure, hindering the normal rotation of the exhaust gas turbine, thereby causing the boost pressure to be too low.

16

2

Share

How much does the Honda CR-V 2021 weigh?

Honda CR-V 2021 has a curb weight of 1.5 tons. Weight of different Honda CR-V models: Depending on the configuration, the weight of the CR-V ranges from 1525kg, 1540kg, 1590kg, 1640kg to 1655kg. Specifications of the Honda CR-V 2021 model: Length/Width/Height (mm): 4550-1820-1685; Wheelbase (mm): 2620; Front track (mm): 1565; Rear track (mm): 1565; Minimum ground clearance (mm): 135; Body structure: SUV; Number of doors: 5; Seating capacity: 5.

13

2

Share

What are the reasons for the malfunction of the Elantra reverse camera?

Damage to the reverse camera causes the Elantra's reverse imaging system to malfunction. Possible causes of reverse camera failure: Disconnection or poor contact of the data cable connected to the reverse camera; damage to the reverse camera; malfunction of the gear position sensor. Reverse imaging system: The reverse camera, also known as the parking assist system, reverse visual system, or onboard monitoring system, provides a clear and intuitive view of the rear when reversing, making it one of the most practical safety features. When the reverse gear is engaged, the system automatically activates the high-definition reverse camera located at the rear of the vehicle, displaying the rear view clearly on the LCD screen to accurately assess the road conditions behind.

6

0

Share

What is the situation when the Equinox makes noise while releasing the accelerator during driving?

When the Equinox makes noise while releasing the accelerator during driving, it is due to a component failure in the accelerator release mechanism. Possible causes: First, the transmission; second, there may be an issue with the valve train; third, it could be engine carbon buildup. These conditions can all potentially cause a noise phenomenon when the accelerator is released during normal driving. Noise locations: Bearing noise: Generally, bearing noise is closely related to engine speed, becoming more pronounced at higher speeds. Differential or main drive gear noise: This type of noise typically becomes noticeable at speeds between 50 to 70 km/h. Due to different gear meshing surfaces, the noise is usually more obvious when accelerating and significantly reduces when releasing the accelerator. Oil pump or hydraulic system noise: This noise is closely related to engine speed but not to vehicle speed. At high speeds, the oil pump may experience suction obstruction, leading to noise.

4

0

Share

Is it necessary to replace Audi spark plugs at a 4S shop?

Audi spark plugs can be replaced either at a 4S shop or at a repair shop. Spark plugs are crucial components of a gasoline engine's ignition system. They introduce high-voltage electricity into the combustion chamber, causing it to jump the electrode gap and generate a spark, thereby igniting the combustible air-fuel mixture in the cylinder. Steps for replacing spark plugs: Open the hood, lift the engine's plastic cover, remove the high-voltage ignition wires, and mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any leaves, dust, or debris on the exterior and ensure they are thoroughly cleaned. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the removed high-voltage ignition wires in the correct firing order, then reattach the cover.

16

0

Share

What is the procedure to follow after a vehicle collision?

Vehicle collision handling procedure is as follows: 1. Preserve the accident scene and promptly report to the traffic management department at the accident location for on-site investigation. If you're determined to be at fault (regardless of degree), you must notify your insurance company. If not at fault, insurance notification isn't required as this affects your no-claim discount for next year's renewal; 2. File the claim promptly. Bring your insurance policy, vehicle registration, and driver's license (if not confiscated) along with the damaged vehicle to your insurer. Complete the Vehicle Accident Registration Form and Accident Notification Form at the claims department, assisting claims adjusters with vehicle inspection; 3. Damage assessment. Take the Vehicle Accident Registration Form to the claims department's assessor to determine repair items and costs; 4. Vehicle repair. When delivering the car for repairs, present the Damage Assessment Sheet to the repair shop. The shop will perform repairs according to the specified items. After repairs, pay the fee using the Vehicle Pick-up Slip to retrieve your car, while obtaining repair invoices stamped with the shop's official seal, Repair Authorization Form, Work Order, and Parts List; 5. Obtain accident certification. Bring the other party's repair invoice and jointly visit the traffic police station to close the case, obtaining an officially stamped Accident Certificate to reclaim any confiscated documents.

18

5

Share

Is the Mercedes-Benz C260 compliant with China VI emission standards?

Why is the boost pressure too low in BMW N54 engine?

How much does the Honda CR-V 2021 weigh?

What are the reasons for the malfunction of the Elantra reverse camera?

What is the situation when the Equinox makes noise while releasing the accelerator during driving?

Is it necessary to replace Audi spark plugs at a 4S shop?

What is the procedure to follow after a vehicle collision?

How to adjust the brightness of Audi A6 low beam headlights?

What is the fuel consumption of BMW X6 3.0t?

Why did the BMW 3 Series air conditioning suddenly have weaker airflow?

How Often Should the Refrigerant in a New Car Be Replaced?