Is the Magotan GTE a hybrid model?

1 Answers
AdrielAnn
07/30/25 10:39am
The Magotan GTE is a plug-in hybrid model. A plug-in hybrid refers to a new energy vehicle that falls between pure electric vehicles and fuel-powered vehicles. The Magotan GTE is equipped with a 1.4-liter turbocharged engine, which delivers 150 horsepower and a maximum torque of 250 Nm. The engine's maximum power output is achieved between 5,000 to 6,000 rpm, while the maximum torque is available from 1,750 to 3,000 rpm. The Magotan GTE is a mid-size sedan produced by FAW-Volkswagen, with body dimensions of 4,865 mm in length, 1,832 mm in width, and 1,469 mm in height, and a wheelbase of 2,871 mm. The front suspension type is MacPherson independent suspension, and the rear suspension type is multi-link independent suspension.
Was this review help?
3
5
Share
More Forum Discussions

What is Cylinder Bank 1 Sensor 1?

Cylinder Bank 1 Sensor 1 refers to a pre-catalytic converter oxygen sensor malfunction. The diagnostic methods for a faulty pre-catalytic oxygen sensor are as follows: 1. Read the pre-catalytic oxygen sensor data stream: The voltage should fluctuate between 0.1~1V, with changes occurring more than 8 times per 10 seconds. If the voltage fluctuates between 0.1~0.5V, it indicates a lean air-fuel mixture; if between 0.5~1V, it indicates a rich mixture; if remains static at 0.4~0.5V, it indicates sensor damage. 2. Check the oxygen sensor resistance: After the engine reaches normal operating temperature, disconnect the sensor wiring harness and measure resistance with an ohmmeter. The value should match the vehicle manufacturer's specifications. 3. Test the sensor's voltage output signal: With the sensor reconnected, extend a test lead. Start the engine, warm it to normal temperature, and maintain idle. Monitor the sensor's output voltage. When disconnecting a spark plug wire, exhaust oxygen content decreases - if the voltmeter shows increased voltage, the sensor functions properly. 4. Observe the sensor tip color for fault identification: (1) Black tip indicates carbon contamination - remove and clean carbon deposits; (2) White tip indicates silicon contamination from using non-compliant sealants during repairs - requires sensor replacement; (3) Reddish-brown tip indicates lead contamination from using leaded gasoline.
20
3
Share

What is the reason why the 2013 Lavida remote control cannot raise the windows?

The reasons why the Volkswagen Lavida car key cannot raise or lower the windows are: 1. The window lift motor is damaged or the wiring harness has poor contact. 2. The motor is overheated. 3. The guide rail is blocked or the rubber seal is aged. 4. The window lift switch is damaged. 5. The safety switch has poor contact or is not connected. Extended content, relevant introduction about Lavida is as follows: 1. Introduction: Lavida is a sedan produced by Shanghai Volkswagen and was launched in June 2008. While continuing the "dynamic and stylish" design language of the A-class models, the LAVIDA Lavida embodies a new design DNA—"fusion." 2. Technical highlights: The design of Lavida originated from the Nezha concept car at the 2006 Beijing Auto Show. The design elements derived from the Nezha concept car previewed the basic style of Volkswagen's localized sedan design in China. Compared to Volkswagen's products in Europe, the design of Nezha is relatively understated.
4
1
Share

What does the W in motor oil mean

Engine oil model in the letter w is the abbreviation of winter, which means winter. More information about engine oil is as follows: 1. If there is a letter w in the engine oil model, it means that this engine oil can be used normally in winter. In the engine oil model, the number in front of w indicates the low-temperature fluidity of the engine oil, and the number behind w indicates the high-temperature viscosity of the engine oil. 2. Engine oil is the blood of the engine. If there is no engine oil in the engine, the engine cannot run normally. Engine oil has six major functions in the engine, namely cleaning, lubrication, heat dissipation, rust prevention, buffering, and sealing. 3. There are many models of engine oil. When choosing engine oil, you must choose the engine oil model suitable for your car engine according to the technical characteristics of your car engine. 4. The performance of engine oil will decay after long-term use, so all engine oil needs to be replaced regularly. If the engine oil is not changed for a long time, it will aggravate the wear of the engine. Every time the engine oil is changed, the engine oil filter element should be replaced together. The engine oil filter element is very important for the engine. Without this component, the engine oil will become very dirty after a period of use, which will affect the normal lubrication of the engine.
18
2
Share

What to Do If You Violate Traffic Rules During the Period of Driver's License Suspension?

If a driver operates a motor vehicle during the period when their driver's license is suspended, it is considered as driving without a license. The public security department will impose a fine on the driver for the violation. According to the regulations on the use of driver's licenses, driving a motor vehicle on the road during the period of license suspension is a violation that will result in a one-time deduction of 6 points from the driver's license.
18
4
Share

How to Deal with a Locked Geely Vision Anti-Theft System That Prevents Starting?

Turn the steering wheel forcefully while turning the key, and the steering wheel lock can usually be released quickly. Ensure the gear is in the P position when igniting. It is recommended to place the smart key on the start button and then press the button to start. If the battery is drained due to reasons like leaving the headlights on for a long time or the battery lifespan has expired, replacing the battery in time according to the maintenance manual can generally resolve the issue.
8
5
Share

How to reset the auto-dipping rearview mirror?

Turn on the vehicle power without starting the engine (do not press the brake pedal); Set the memory seat and select the seat position; Choose the rearview mirror and press the mirror adjustment selection button; Press the brake pedal and shift to R gear, the selected mirror will automatically dip to the factory preset position, then use the 4-way adjustment button to set it to the desired position; Press and hold the seat memory button for about 2 seconds; Press the brake pedal, shift to P gear, then press the mirror adjustment selection button once more.
1
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.