Is the Magotan Engine Imported or Domestically Produced?

1 Answers
DeAurora
07/29/25 9:06pm
The Magotan uses a domestically produced engine, manufactured in Dalian City. The engine model used in the Magotan is the EA211-DJS, with a maximum horsepower of 150 HP, a maximum power of 110 KW, a maximum power speed range of 5000-6000 rpm, and a maximum torque of 250 Nm. For daily maintenance of the Magotan's engine, the following methods can be employed: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD to SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions. For diesel engines, choose CB to CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine issues. To prevent faults, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through, the filter may burst or open the safety valve, allowing oil to bypass and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to flush the radiator. Removing rust and scale deposits not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
Was this review help?
15
2
Share
More Forum Discussions

Will an automatic car roll if parked in P gear without engaging the handbrake?

An automatic car will not roll if parked in P gear without engaging the handbrake. The relevant introduction to P gear usage is as follows: Principle of P gear: It mechanically locks the output shaft of the transmission to secure the car and prevent it from moving. Procedure for parking in P gear: After the car comes to a complete stop on a level surface, shift the gear from D to P, then engage the handbrake to complete the parking process, and finally turn off the engine. Safe parking method: If you only apply the brakes without shifting into P gear, the car may lose its braking capability. The safest and most reliable method is to shift into P gear after the car has come to a complete stop.
5
2
Share

When to Use D+ or - in Automatic Transmission Cars?

Below is the usage of D+/- in automatic transmission: Meaning of D+/-: The "D+" and "D-" in automatic transmission refer to the manual mode of the car. When the gear is in D, moving the gear lever to the left or right switches to manual mode. In manual mode, you can shift gears by operating "D+" and "D-". Pushing towards "D+" shifts up, while pushing towards "D-" shifts down. Usage of D+/-: When going downhill, you can use "D+" to shift to D2 or D3. Downhill driving utilizes the engine's braking effect, and 2nd or 3rd gear can meet the power demand. "D+" is also needed. When going uphill, the power demand is higher, so "D-" should be used to downshift the vehicle for climbing. Similarly, if the vehicle starts to accelerate downhill uncontrollably, use "D-" to downshift and control the speed. Additionally, "D-" can be used for short overtaking or in congested road conditions.
12
0
Share

Why Doesn't the Automatic Transmission Car Move When Stepping on the Gas?

Automatic transmission cars not moving when stepping on the gas can be due to the following reasons: Fuel system issues: After prolonged use, carbon deposits may form on the fuel injectors, leading to clogging. This can cause fuel line leaks, clogged fuel filters, and other fuel system problems. Intake system problems: The air filter among the three filters requires the most frequent cleaning or replacement. If the air filter becomes clogged or the throttle system is blocked, the air intake decreases, resulting in incomplete combustion and reduced power. Engine misfire: Power issues are closely related to the engine. If the car shakes at idle and experiences power loss, it may indicate an engine misfire. In this case, it is recommended to conduct a comprehensive inspection at a professional repair shop.
5
0
Share

What Causes Automatic Parking System Failure?

Automatic parking system failure can be caused by the following reasons: Lever cannot be fixed: The parking brake lever cannot be fixed; the lever needs to be replaced or reinstalled. Brake failure: The parking brake fails; it is necessary to inspect and replace parts such as brake pads. If the parking brake makes abnormal noises or is aged, lubricant should be added or the brake should be replaced. Excessive gap: If the friction pads of the automatic parking system have too large a gap with the brake drum, or if there is oil contamination, severe wear, exposed rivets, or surface hardening causing slippage, the brake pads and brake disc should be replaced.
4
1
Share

Should You Shift to Neutral When Parking an Automatic Car?

If you are waiting at a red light or only stopping for a couple of minutes, you can shift to neutral, but you must keep your foot on the brake, and it's best to engage the handbrake. If you are parking the car and leaving it unattended for an extended period, it is not recommended to leave it in neutral; instead, shift to P (Park). Parking Steps: The correct parking procedure is as follows: First, press the brake pedal, shift from D (Drive) to N (Neutral), then engage the mechanical handbrake or electronic parking brake. This step ensures that all the force is absorbed by the handbrake. Next, shift from N to P (Park), and then turn off the engine. This is the proper parking procedure. Parking on a Slope: When parking on a slope, it is even more important to follow the above steps. If you shift directly from D to P while parking on a slope, it can cause significant damage to the transmission because the locking mechanism of the transmission will bear excessive force.
8
1
Share

Can you overtake by borrowing the lane with a yellow dashed line?

The yellow dashed line in the center of the road indicates that it is possible to cross the line for overtaking if safety is ensured. When overtaking, pay attention to the following: Reduce speed and honk: When passing a parked vehicle, you should slow down and honk (in areas where honking is not prohibited), observe carefully, stay alert, maintain a large lateral distance, and be prepared to brake at any time to prevent the vehicle from suddenly starting and entering the traffic lane, causing a collision, or the driver suddenly opening the door and getting out. Especially when overtaking a bus parked at a station, be extra cautious of pedestrians suddenly crossing the road from behind the parked vehicle. Situations where emergency braking is not needed: If you find obstacles on the left side of the road or the lateral distance is too small, making a side collision possible, try to avoid emergency braking to prevent side-slip collisions due to road camber. Instead, hold the steering wheel steady without turning it left or right, increase the distance appropriately in the shortest time, and then look for another opportunity to overtake. Never take the risk of forcing an overtake.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.