Is the longer valve spring on the Teana for intake or exhaust?

1 Answers
LukasAnn
09/07/25 3:44am
The longer valve spring on the Teana is for the exhaust. In terms of engine structure, valves are divided into intake valves and exhaust valves. Here is the relevant information: 1. Function of the intake valve: It draws air into the engine to mix with fuel for combustion. 2. Function of the exhaust valve: It expels the burned exhaust gases and dissipates heat. 3. Symptoms of damaged car valves: (1) It will affect the engine's efficiency, reducing the car's power; (2) It will produce abnormal noises, the engine may experience unstable idling or poor acceleration during operation, overtaking performance may also decrease. In severe cases, it can lead to difficulty starting the engine, failure to ignite, and the car may exhibit air leakage or increased carbon buildup.
Was this review help?
17
0
Share
More Forum Discussions

What to Do When a Tire Locks Up?

Generally, if the brake drum gets wet after washing the car or during rain and the handbrake is applied, the tire may lock up after being left for a long time. You can use the vehicle's power to rotate the tire. The solution to this problem is to clean the entire braking system and replace the brake master cylinder rubber cup. You can repair it by sanding with sandpaper and applying grease. If the wheel cylinder itself is faulty, it may need to be replaced directly. Use hot water to melt the ice, or gently tap the brake drum with a blunt object like a hammer a couple of times. Prolonged braking can cause excessive heat, preventing the brake pads from separating on their own. Depending on the situation, the brake pads may need to be sanded or replaced directly.
7
3
Share

What is the special tool for removing the oil filter element?

The special tool for removing the oil filter element is an oil filter wrench. Here is some additional information: 1. Oil filter element: The oil filter element is the oil filter, whose function is to filter out impurities, gum, and moisture from the oil, delivering clean oil to various lubrication points. 2. Classification: Due to the high viscosity of the oil itself and the high content of impurities, oil filters generally have three stages to improve filtration efficiency: the oil strainer, the oil coarse filter, and the oil fine filter. 3. Function: The filter of a diesel generator set is a specialized pre-filtering device for diesel used in internal combustion engines. It can filter out more than 90% of mechanical impurities, gum, asphalt, etc., from the diesel, ensuring maximum cleanliness of the diesel and extending the engine's service life.
20
0
Share

Why Can't the Car Key Be Turned After Insertion?

Here are the main reasons and solutions for why a car key can't be turned after insertion: 1. The car key may not turn due to the automatic steering wheel lock, which is part of the car's anti-theft system. After the vehicle is turned off, the steering lock pin engages with the steering column, preventing the steering wheel from moving. Even with the key inserted, it cannot be turned. 2. When encountering this issue, you can unlock the steering wheel by inserting the mechanical key, pressing the brake pedal, and then gently turning the steering wheel. Although the steering wheel is locked, it can still be slightly moved. While turning the steering wheel, simultaneously turn the key to complete the unlocking procedure, allowing the vehicle to start normally.
6
5
Share

What is the reason for the sudden failure of the automatic folding function of the Mercedes-Benz car's rearview mirror?

The electric folding function of the exterior rearview mirror fails. Excluding mechanical and electronic control reasons, the causes for the Mercedes-Benz rearview mirror not folding automatically are: 1. The battery is disconnected or dead: In this case, the exterior rearview mirror must be reset to function properly. The specific reset method is to manually operate the folding button. 2. After setting "fold the rearview mirror when locking the car," you manually folded it: In this situation, the exterior rearview mirror will not automatically unfold the next time you unlock the vehicle. You need to enter the car and press the button on the door to manually unfold the exterior rearview mirror.
20
0
Share

What engine is equipped in the Ferrari 599?

Ferrari 599 is equipped with a 6.0-liter V12 naturally aspirated engine. This engine has a maximum power output of 456kW, maximum torque of 608Nm, reaches its peak power at 7,600 rpm, and achieves maximum torque at 5,600 rpm. The engine features multi-point electronic fuel injection technology and utilizes an aluminum alloy cylinder head and block. Introduction to the Ferrari 599: 1. The front suspension employs a double-wishbone independent suspension system. 2. The interior design combines the pure sports style of a genuine Ferrari sports car with exquisite detailing and personalized customization options. Its sleek styling and spacious interior create an intense sense of sportiness for the driver.
2
2
Share

What is the service life of brake pads?

Automotive brake pads can generally last for 10 kilometers, while high-quality brake pads can last up to 15 kilometers. Below is more information about automotive brake pads: 1. Automotive brake pads, also known as automotive brake linings, refer to the friction materials fixed on the brake drum or brake disc that rotates with the wheel. The friction lining and friction block bear external pressure to generate friction, thereby achieving the purpose of vehicle deceleration. Automotive brake pads are generally composed of steel plates, adhesive insulation layers, and friction blocks. The steel plates are coated to prevent rust, and the coating process is monitored using an SMT-4 furnace temperature tracker to ensure the temperature distribution during the coating process and guarantee quality. 2. A good and efficient braking system must provide stable, sufficient, and controllable braking force, along with excellent hydraulic transmission and heat dissipation capabilities. This ensures that the force applied by the driver on the brake pedal is fully and effectively transmitted to the master cylinder and sub-cylinders, while avoiding hydraulic failure and brake fade caused by excessive heat.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.