Is the Jetta compliant with China VI emission standards?

1 Answers
MilesLee
07/25/25 5:26pm
Jetta is compliant with China VI emission standards. China VI refers to the National Sixth Stage Emission Standards for Motor Vehicles, which are established to prevent environmental pollution caused by exhaust emissions from compression-ignition and gas-fueled spark-ignition engine vehicles, protect the ecological environment, and safeguard human health. Taking the 2019 Jetta VS5 manual base model as an example, its body dimensions are: length 4419mm, width 1841mm, height 1616mm, with a wheelbase of 2630mm and a fuel tank capacity of 51 liters. The 2019 Jetta VS5 manual base model is equipped with a 1.4T turbocharged engine, delivering a maximum power of 110kW and a maximum torque of 250Nm, paired with a 5-speed manual transmission.
Was this review help?
17
1
Share
More Forum Discussions

Can I still use a temporary license plate if I have a regular one?

No, after the official license plate is issued, you cannot use a temporary license plate as it violates traffic regulations and poses safety hazards. Below is more information about license plates: 1. A paper motor vehicle license plate that temporarily permits a motor vehicle to drive on the road, also known as a temporary driving license plate. It refers to a temporary vehicle driving certificate issued by the vehicle management department of the public security authority before the new vehicle is officially registered. The validity period of a temporary license plate generally does not exceed thirty days. There are four types: temporary license plates for administrative jurisdictions, temporary license plates for cross-administrative jurisdictions, temporary license plates for testing purposes, and temporary license plates for special-type motor vehicles. 2. According to Article 11 of China's "Road Traffic Safety Law": When driving a motor vehicle on the road, the motor vehicle license plate must be displayed, along with the inspection qualification mark and insurance mark, and the motor vehicle driving license must be carried. The motor vehicle driving license and license plate must be displayed as required, kept clear and intact, and must not be deliberately obscured or damaged. No unit or individual may confiscate or detain motor vehicle license plates.
4
2
Share

Will Car Seat Covers Affect Airbags?

Car seat covers may interfere with the deployment of certain airbags. Here is relevant information about car seat covers and airbags: 1. Since most car seat covers do not have special treatment for airbag positions, they may prevent airbags from deploying during a collision. 2. The side airbags are most affected by car seat covers. Side airbags are installed in the seat back near the door, and original factory seats have corresponding weakened areas to ensure the airbags deploy in a specific shape. 3. When choosing car seat covers, owners should consider the airbag positions corresponding to their vehicle model and select appropriate seat covers.
19
0
Share

Is it feasible to turn off the engine in N gear for an automatic transmission?

It is not advisable to turn off the engine in N gear for an automatic transmission vehicle. For safety reasons, an automatic transmission car must be shifted into P gear before turning off the engine. The correct method to turn off the engine is: Step on the brake; Shift into N gear; Engage the handbrake; Release the foot brake to ensure the vehicle does not move; Shift into P gear; Turn off the engine. Below is additional information about N gear and P gear: 1. Both P gear and N gear disconnect the engine and the wheel transmission system from operation. The only difference is: when the engine is stopped, a vehicle in N gear can be pushed freely, while a vehicle in P gear cannot move. This is because when shifted into P gear, a pawl inside the transmission locks the transmission output shaft, preventing the vehicle from moving. 2. Increasingly, many car models are configured at the factory to prevent the engine from being turned off unless the vehicle is in P gear. This is to prevent the vehicle from moving due to external forces if the driver forgets to engage the handbrake, which could lead to accidents. 3. Always engage the handbrake before shifting into P gear. Only the handbrake can truly prevent the vehicle from moving.
14
4
Share

How often should the CVT transmission fluid in a Corolla be changed?

The CVT transmission fluid in a Corolla is generally recommended to be changed every two years or approximately 60,000 kilometers. The Corolla uses a CVT continuously variable transmission (simulating 8 gears) and an E-CVT continuously variable transmission. The replacement intervals vary for different types of vehicles. Below are the recommended replacement intervals for transmission fluid. Manual Transmission: Manual transmission fluid is generally recommended to be changed every three years or approximately 100,000 kilometers. Automatic Transmission: Automatic transmission fluid is generally recommended to be changed every two years or approximately 40,000 kilometers. Continuously Variable Transmission (CVT): CVT transmission fluid is generally recommended to be changed every two years or approximately 60,000 kilometers. The methods for changing transmission fluid are as follows: 1. Loosen the drain screw at the bottom of the transmission to drain the old fluid, then refill with new fluid. 2. Remove the transmission oil pan directly to drain the old fluid and refill: This method is more thorough than the previous one, as it removes impurities from the bottom of the oil pan. 3. Use a circulation machine to change automatic transmission fluid: A smart circulation machine can perform dynamic fluid replacement, filtering and cleaning sludge and impurities inside the automatic transmission.
15
5
Share

What causes the water sound when turning in the Trumpchi GS4?

The reasons for the water sound when turning in the Trumpchi GS4 are: first, the power steering pump may be making noise; second, the outer CV joint of the front drive shaft may be noisy. It is necessary to go to a 4S shop or repair shop to check if the outer CV joint boot is damaged. If the situation is confirmed, the outer CV joint needs to be replaced. Here is some related information: 1. Positioning: The GAC Trumpchi GS4 is positioned as an "International New Trend SUV" and was officially launched on April 18, 2015, with a total of 8 models introduced. 2. Engine: The new Trumpchi is equipped with a second-generation 200T engine. The low-inertia E-TURBO turbocharging technology can enhance low-speed torque, providing a powerful driving experience. The GCCS combustion control patent technology effectively ensures the engine's high torque and low fuel consumption. It also features a START-STOP engine start-stop system, significantly improving fuel economy and reducing emissions. The engine delivers a peak torque of 202N.m within a speed range of 1500—4200rpm, with a combined fuel consumption of only 6.3L per 100 kilometers.
20
2
Share

How Long is the Warranty for the Geely Emgrand Water Pump?

The warranty period for the Geely Emgrand water pump is three years. Automotive engines widely use centrifugal water pumps. Their basic structure consists of the water pump housing, connecting plate or pulley, water pump shaft and bearings or integrated bearing, water pump impeller, and sealing components, which are key parts of the vehicle. The repair method for a leaking water pump is as follows: 1. Remove the water pump: First, drain the coolant from the water pump, remove the V-belt, use a special tool to press out the water pump pulley, and then dismantle the water pump; 2. Disassemble the water pump: Use a special tool to first remove the water pump bearing, then detach the water pump impeller and sealing assembly from the bearing; 3. Replace the sealing ring, new gasket, new V-belt, and new pulley; 4. Reassemble: Use a special tool to press the bearing onto the water pump impeller first, then press the impeller and sealing assembly into the designated position, and press the water pump bearing onto the pulley seat. During the operation, ensure the bearing end face is flush with the housing, and the impeller plane is 0.1-0.3mm lower than the pump housing plane; 5. Inspection: The assembled water pump should have a shaft that rotates smoothly, and the bearing should have no noticeable radial play; 6. Refill with new coolant.
9
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.