···
Log in / Register

Is the inner lane on the left or right side?

4 Answers
DeAvery
07/30/25 12:05am

Inner lane is on the left. Here is some knowledge about lanes: 1. Lane division: Starting from the left side of the road in the direction of vehicle travel, the first lane is the overtaking lane (with a designated speed of 100-120 km/h), while the second and third lanes are the main travel lanes. 2. Emergency lane: The lane adjacent to the main lane (the far right) is the shoulder (also called the emergency stopping lane). It is used for emergency stops when vehicles break down or when accidents occur on the main lanes, serving as an emergency rescue passage. At such times, other vehicles are not allowed to use the shoulder (emergency stopping lane) for parking.

Was this review help?
19
3
Share
JosiahLynn
08/16/25 3:57am

The inner lane on right-hand traffic roads is usually the leftmost lane, adjacent to the centerline or median divider. I remember when I first started driving on highways, I also got confused—always thinking the right side was the inner lane, but actually had the direction wrong. Since the inner lane is used for overtaking and as the fast lane, its left-side position allows vehicles to pass slower traffic more safely. My driving instructor taught me that on standard roads, the left inner lane has higher speeds and is more prone to accidents, so beginners need to be especially careful not to change lanes recklessly, particularly in low-visibility conditions like heavy fog or at night. Now, I’ve gotten used to using navigation tools to check road designs in advance. Some areas may temporarily alter the inner lane position due to construction or roundabouts, but the basic principle remains the left side. Understanding this is super helpful for avoiding rear-end collisions and speeding fines. A few more practice runs on the highway, and it’ll become second nature.

Was this review help?
17
3
Share
Expand All
EzraMarie
10/19/25 5:51am

When I first started learning to drive, the instructor explained that the inner lane is usually on the left side, meaning it's closer to the center of the road. I remember being very nervous during my first time on the highway—the left lane had faster traffic, while the right outer lane near the shoulder was the slow lane. This design helps keep traffic flowing smoothly. After a few tries in practice, I understood: the left inner lane is good for when you're in a hurry, but be careful not to hog it for too long, especially as a beginner prone to misjudgments that could lead to scrapes. I recommend checking traffic manuals or app guides more often—they mark lane usage changes, like how the inner lane in urban intersections might temporarily adjust for left turns. The key to safe driving is knowing the rules and gradually gaining confidence through experience.

Was this review help?
9
4
Share
Expand All
StEmma
12/02/25 6:25am

As a parent who frequently drives, I understand that the inner lane on regular roads always refers to the leftmost lane closest to the center. This arrangement has its reasons—the left inner lane serves as the fast lane for overtaking, helping to reduce congestion. I always remind myself and my family not to frequently switch to the left lane when driving slowly to avoid reckless drivers. Especially when picking up or dropping off kids, safety comes first. Knowing your position can prevent accidents, and extra caution is needed during rainy days or peak hours. Remember, the right lane is the outer lane and tends to be more stable.

Was this review help?
1
0
Share
Expand All
More Forum Discussions

What are the effects of not having a three-way catalytic converter on a car

It has no effect on the car, but it has a very significant impact on the environment. If the three-way catalytic converter is damaged, the car will emit a large amount of harmful gases, and may even cause harmful gases to enter the car, affecting the health of the occupants. If the three-way catalytic converter is not repaired in time, it may cause the vehicle to fail the annual inspection, resulting in fines, vehicle impoundment, and other situations. The three-way catalytic converter is the most important external purification device installed in the vehicle's exhaust system. It can convert harmful gases such as CO, HC, and NOx emitted from the vehicle's exhaust into harmless carbon dioxide, water, and nitrogen through oxidation and reduction. The following are the effects of a damaged three-way catalytic converter on the car: 1. Symptoms of a damaged three-way catalytic converter: Shortly after the vehicle is started, the exhaust manifold emits a noticeable red burning phenomenon to the three-way catalytic converter, and a hissing sound of air leakage and gurgling can be heard when accelerating. 2. Consequences: If the three-way catalytic converter is damaged, the secondary oxygen sensor will not be able to accurately provide data to the driving computer. As a result, the concentration of the air-fuel mixture will become too lean or too rich. If it is too lean, it will cause difficulties in ignition, weak driving, and engine misfires. If it is too rich, it will increase fuel consumption, incomplete combustion, and severe carbon deposits in the cylinders and spark plugs. When this fault occurs, the engine fault light should illuminate.
7
4
Share

What Happens When a Motorcycle Engine Overheats?

Here are the specific hazards: 1. Decrease in engine charging efficiency: The higher the temperature, the lower the air density, resulting in reduced actual air intake by the engine. Due to engine overheating, the temperature inside the engine compartment rises further, diminishing the engine's charging capacity. This decline in charging efficiency leads to a drop in engine power, causing the vehicle to lose driving force. Additionally, as the charging efficiency decreases, the air-fuel mixture becomes relatively richer, increasing the concentration of harmful substances (CO, HC, NOx, soot) in the vehicle's exhaust and exacerbating environmental pollution. 2. Abnormal engine combustion: High ambient temperatures raise the temperature of the air-fuel mixture entering the cylinders, elevating the overall operating cycle temperature of the engine. Coupled with the radiator's reduced cooling efficiency, the engine enters an overheated state. The end-gas mixture in the combustion chamber absorbs excessive heat, accelerating pre-flame reactions and increasing the likelihood of engine knocking. Furthermore, an overheated engine causes carbon deposits on the piston top, combustion chamber walls, valve tops, and spark plugs to form hot spots, potentially leading to premature ignition of the combustible mixture. This abnormal combustion further worsens the engine's overheating, creating a vicious cycle. The cylinder block and head are prone to thermal deformation or even cracking, with common issues including burning out the cylinder head gasket, valves, and valve seats. 3. Engine oil degradation: Under high temperature and pressure, the engine oil's oxidation stability deteriorates, hastening its thermal decomposition, oxidation, and polymerization. The oil mixes with incomplete combustion byproducts, condensed water vapor, and dust from the intake air, leading to oil degradation. Moreover, elevated oil temperatures reduce viscosity, thinning the oil and diminishing its lubricating properties, which lowers oil pressure and makes it harder to form a protective lubricating film on engine components. Simultaneously, metal parts expand significantly due to heat, reducing normal clearances between components. These factors accelerate wear and tear, severely impacting the engine's lifespan. 4. Fuel system vapor lock: Higher temperatures increase the likelihood of vapor lock in the engine compartment. When the fuel system heats up, some gasoline evaporates into gas within the fuel lines and pump, not only increasing flow resistance but also, due to the compressibility of gas, causing fuel vapor in the pump's outlet line to compress and expand with the pump's pulsating pressure. This disrupts the vacuum created during the pump's suction phase, leading to insufficient or interrupted fuel supply—a condition known as vapor lock. This phenomenon is more common in hot climates, especially when the vehicle is fully loaded climbing hills or driving at low speeds for extended periods. 5. Ignition system malfunction: In high-temperature environments, the ignition coil may overheat, weakening the high-voltage spark and causing engine misfires at high speeds. In severe cases, the ignition coil may burn out, affecting normal vehicle operation.
19
4
Share

Is the purchase invoice required for the first maintenance?

The purchase invoice is required for the first maintenance. The items needed for the first maintenance include: driver's license; maintenance manual; warranty manual; owner's ID card; vehicle's registration certificate; vehicle's purchase invoice. Bring these to the designated first maintenance facility for the vehicle's first maintenance. Note: Make an appointment with the 4S shop in advance. The first maintenance refers to the initial maintenance after the new car has been driven. The specific time varies by car, usually after driving 1,000 to 3,000 kilometers. The car needs to undergo the first maintenance promptly, neither in advance nor delayed. The completion of the first maintenance marks the end of the car's break-in period, allowing it to be driven according to the standard load and normal speed required by the car. The time for the first maintenance is calculated based on the date the car was picked up. There are two indicator values for the first maintenance time: mileage and time. Whichever comes first will be the standard. The first maintenance items include: changing the engine oil and oil filter, cleaning the air filter, checking various oil levels for normalcy, inspecting the generator belt and wiper blades for damage, checking tire pressure for normalcy, and inspecting tires for damage or bulges. Required time: Completing all tasks takes about 2 hours. The most important aspect of the first maintenance for a new car is changing the engine oil and oil filter. When changing the engine oil, the oil filter must also be replaced. The selection of engine oil must refer to the "Vehicle User Maintenance Manual," as different car models specify different engine oil grades. Maintenance precautions: Do not rinse the interior of the car body with water: Many people clean their cars during holidays, using water to wash the body and wiping it with a cloth. It is important to note that the interior of the car body should not be directly rinsed with water. If the floor mats are dirty, use a vacuum cleaner or take them out to brush and clean with detergent, dry them, and then put them back. There are many holes under the rubber mats on the floor of the driver's compartment. If water enters, it will not dry but flow through these holes to parts like the gearbox, causing erosion and corrosion. The best practice is to use a vacuum cleaner for cleaning and then wipe with a cloth to prevent water accumulation. Do not mix different brands of antifreeze: When the antifreeze in the car is low, it is recommended to drain the antifreeze first and then add the same brand of antifreeze. Since antifreeze brands differ, their chemical properties vary greatly. Various functional additives may corrode others. Different brands of antifreeze use different additives, so they should not be mixed to avoid unnecessary trouble. Do not lubricate tire bolts and nuts: When the bolts on a moving car rust, they are often oiled to function properly again. To prevent the bolts and nuts on the wheels from rusting, some people apply lubricant to them, which can pose a safety risk. When the car is driven at high speed, the bolts and nuts may loosen or even fall off, leading to driving malfunctions. Do not press the accelerator when starting an EFI car: The starter of an EFI car is different from that of a regular car. Its fuel injection control device can automatically adjust the fuel supply based on the starter's temperature and operating conditions, ensuring a smooth start.
13
4
Share

What to Do If the Lavida's Door Has Abnormal Noises?

Lavida's door has abnormal noises due to the following reasons: 1. If it is caused by loose components creating friction noise, simply tighten them; 2. If the noise is due to rust, use rust remover and lubricant for treatment; 3. If the noise comes from the mechanical structure of the door cable, the door needs to be disassembled for a thorough inspection. The Lavida is the first independently developed A-segment car by Shanghai Volkswagen, featuring a front-end design that significantly differs from previous A-segment models under the Volkswagen brand, especially its unique teardrop-shaped headlights. In terms of dimensions, the Lavida measures 4605mm in length, 1765mm in width, and 1460mm in height.
19
0
Share

What is the GF-6 Engine Oil Standard?

GF-6 standard is divided into GF-6A and GF-6B. The following are the specific details of the GF-6 standard: 1. Effective Date: May 2020, when GF-6A came into effect, replacing GF-5 and earlier standards. 2. Incompatibility with Older Standards: GF-6B is not compatible with previous older standards and is only recommended for use in new vehicles requiring 0W-16 oil, primarily Japanese cars at present. 3. Not Recommended Oils: Similar to the GF-5 standard, GF-6A/B does not recommend any xW-40 viscosity oils, mainly due to greater consideration for fuel economy. Currently, API-SP can still be found in xW-40 viscosity oils.
20
0
Share

How to Determine the Right Time to Shift Gears?

When shifting gears, it's essential to consider the engine's performance and the overall vehicle matching to decide the appropriate gear. You can base your decision on the engine's RPM or the vehicle's speed changes. During manual shifting, moving the gear lever inward from neutral engages first gear, and pulling it downward from first gear engages second gear, with the highest gear typically being fifth. Manual transmissions offer higher sensitivity, making them a preferred choice for professional drivers. Additionally, manual transmission vehicles tend to have better fuel economy compared to automatic models. To start the car, quickly depress the clutch, then slowly release it while shifting into first gear. Gradually lift the clutch to the engagement point, then press the accelerator to move. For reversing, shift into the reverse gear.
13
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.