Is the imported Pajero a four-wheel drive?

2 Answers
AdalineDella
09/05/25 4:36am
Imported Pajero is a four-wheel drive vehicle, equipped with a full-time four-wheel drive system. There are three common types of four-wheel drive systems in vehicles: full-time four-wheel drive, part-time four-wheel drive, and on-demand four-wheel drive. The imported Pajero is a rugged off-road vehicle, positioned as a mid-size SUV, with body dimensions of 4785mm in length, 1815mm in width, and 1805mm in height, and a wheelbase of 2800mm. The Pajero is powered by a 3.0-liter V6 naturally aspirated engine, which delivers 174 horsepower and a maximum torque of 255 Nm. This engine can output its maximum power at 5250 rpm and its maximum torque at 4000 rpm. It is paired with a 5-speed automatic transmission.
Was this review help?
14
5
Share
EverlyMarie
09/17/25 5:06am
I've driven the imported Pajero a few times, and this car is definitely a classic example of four-wheel drive! The Pajero's signature feature is its Super Select 4WD system, which allows easy switching between two-wheel and four-wheel drive modes, performing exceptionally reliably during off-road activities like climbing hills or fording streams. During my last test drive in the suburbs, it didn't hesitate even on rough roads, with balanced four-wheel power distribution preventing skidding. Generally, the imported versions come standard with this, but it's important to note that there might be slight variations between different year models. For example, older Pajero models had a four-wheel drive lock, while newer ones are more electronic and easier to operate. People who choose it mainly value the all-weather safety provided by the four-wheel drive, especially in rain, snow, or during outings, reducing the risk of accidents. In short, this is the soul of the Pajero. If you often drive on complex terrains, don't miss out on this advantage.
Was this review help?
18
2
Share
Expand All
More Forum Discussions

What to Do When the Driver Information Recorded on the Driving License Changes?

If the driver information recorded on the motor vehicle driving license changes, or if the driving license is damaged and becomes illegible, the driver must apply for a replacement license within 30 days at the vehicle management office where the license was originally issued or at another vehicle management office outside the original issuing jurisdiction. If applying at a vehicle management office outside the original issuing jurisdiction, transfer procedures must be completed as required. The guidelines for applying for a replacement motor vehicle driving license are as follows: 1. Required documents: "Application Form for Motor Vehicle Driving License"; the driver's identity proof; the original driving license; two recent photographs of the driver (specifications: front-facing, full-color, bareheaded, half-length ID photo taken within the last 6 months, white background, no uniform, dimensions 32mm×22mm, head width 14mm-16mm, head length 19mm-22mm, resolution 300dpi). 2. Eligibility criteria: The driver information recorded on the driving license has changed within the jurisdiction of the vehicle management office; the driving license is damaged and illegible; the applicant does not have any of the following conditions: accumulated 12 penalty points, overdue inspection, license under seizure, detention, suspension, cancellation, revocation, or annulment.
12
1
Share

What lights should be used when overtaking at night?

When using lights for overtaking with a motor vehicle at night: Turn on the left turn signal in advance, alternate between high and low beams, or honk the horn. Due to poor visibility at night, you should alternate between high and low beams to alert other vehicles. Here are some precautions for night driving: 1. Increase the following distance. When driving at night, the driver's visibility is not as broad as during the day, and they often encounter dangerous or emergency situations. Therefore, the driver must be prepared to stop at any time. Under these circumstances, to avoid danger, it is important to appropriately increase the following distance to prevent collisions between vehicles. 2. Try to avoid overtaking. Before overtaking, observe whether there are obstacles on the right side of the vehicle being overtaken to prevent the overtaken vehicle from swerving to the left to avoid obstacles and causing a collision. If overtaking is necessary, continuously alternate between high and low beams to inform the vehicle ahead in advance, and only proceed with overtaking after confirming it is safe to do so. 3. Overcome driving fatigue. Night driving, especially after midnight, is most likely to cause fatigue and drowsiness. Additionally, since the driver cannot see the scenery on both sides of the road, there is less stimulation to keep them alert, making it easier to experience driving fatigue.
19
2
Share

What is the idle speed of a car?

Engine idle speed is normally between 1100-1500 RPM. Idle condition generally refers to the state where the throttle is fully released and the engine runs naturally. The engine speed in a cold state is higher than in a warm state, primarily to allow the engine to quickly warm up to its normal operating temperature, ensuring good lubrication. Below are relevant details: 1. Idle speed too high/too low: (1) Causes of high/low engine idle speed: Idle switch not closing (faulty idle control valve), intake manifold leak, incorrect valve timing, clogged or poor atomization of fuel injectors, blocked exhaust pipe, etc. (2) Solutions for high/low engine idle speed: Adjust or replace the throttle position sensor; clean or replace the idle control valve and use a specialized decoder for basic idle settings; clean and inspect fuel injectors to meet atomization requirements; replace the catalytic converter; locate system leaks. 2. Precautions during idle: (1) Minimize the use of high-power electrical devices such as air conditioning, high-power audio systems, and external power supply, as these increase the load on the battery and engine. (2) If the engine idle is unstable, shakes, or the RPM is too high or low, avoid driving and promptly check the vehicle's technical condition to prevent issues like stalling or loss of power while driving.
11
1
Share

What does China VI mean for passenger cars?

China VI for automobiles refers to vehicles that comply with the National Phase VI Motor Vehicle Pollutant Emission Standards. The China VI standard, officially known as the 'National Phase VI Motor Vehicle Pollutant Emission Standards,' includes 'Limits and Measurement Methods for Emissions from Light-duty Vehicles (China VI)' and 'Limits and Measurement Methods for Emissions from Heavy-duty Diesel Vehicles (China VI).' Here are the relevant details: 1. China VIa and China VIb: Currently, the 'China VI standard' is divided into two phases, 'China VIa' and 'China VIb,' with nationwide implementation planned for 2020 and 2023, respectively. The China VI standard, or 'National Phase VI Motor Vehicle Pollutant Emission Standards,' was established to enforce environmental protection laws, reduce and prevent vehicle exhaust pollution, protect the ecological environment, and ensure human health. 2. Differences between China VIa and China VIb: The emission standard data for China VIa and China VIb clearly show the differences between them. Compared to China VIa, China VIb imposes stricter requirements on the emissions of carbon monoxide, non-methane hydrocarbons, nitrogen oxides, and PM particulate matter, with significantly tighter limits. China VIa essentially serves as a transitional phase to China VIb.
11
0
Share

Is Roewe a Domestic Car Brand?

Roewe is an independent automotive brand under Shanghai Automotive Industry Corporation (Group) and is a domestic car. Here is some extended information: 1. Roewe Development: On October 12, 2006, SAIC Motor Corporation Limited (hereinafter referred to as "SAIC Motor") officially announced that its independent brand would be named "Roewe," which means "Innovation Glory, Prestige Worldwide." 2. Additional Information: "Roewe" products will be positioned in the mid-to-high-end segment of different market levels, targeting consumers who are knowledgeable, cultivated, successful in their careers, innovative, proactive, and pursuing taste.
17
3
Share

What does HOLD mean on a car?

HOLD means to maintain. After pressing this button, the automatic transmission is in hold mode, and the hold mode indicator light on the instrument panel will illuminate. The HOLD button adjusts the optimal driving state according to different road conditions, effectively preventing frequent gear shifts in the transmission. It also serves to force a downshift without upshifting during overtaking. The HOLD function can be used in the following situations: 1. Slippery road surfaces, such as starting on snow: Starting in snow with 2nd gear instead of 1st gear is smoother. When starting on snow, you can place the gear lever in position 2 and press HOLD, so the transmission will maintain the gear ratio in 2nd gear, resulting in a smoother start. 2. Driving on continuous curves: When driving on continuous curves, the automatic transmission in normal mode may frequently shift due to the driver's control of the accelerator pedal. Pressing the HOLD key in 4th gear will activate hold mode, keeping the transmission in 3rd gear. This not only reduces transmission wear but also allows the transmission to continuously output greater torque during driving, improving acceleration performance and making the ride smoother. 3. Driving on mountainous roads or continuous slopes: Pressing the HOLD key in 4th or 2nd gear to enter hold mode provides stronger acceleration when going uphill. When going downhill, it offers greater engine braking for safer driving, avoiding wear caused by frequent gear shifts in the transmission.
2
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.