Is the Honda Lingpai from Guangqi Honda or Dongfeng Honda?

1 Answers
VonRiley
07/30/25 10:19am
The Honda Lingpai is from Guangqi Honda. Here is more information about the Lingpai: 1. The predecessor of the Lingpai was the Conpect C concept car unveiled by Guangqi Honda at the 2012 Guangzhou Auto Show, marking Guangqi Honda's first compact car. The vehicle measures 4650mm in length, 1750mm in width, and 1505mm in height, with a wheelbase of 2650mm. 2. The exterior of the Lingpai adopts the manufacturer's design philosophy called 'Cool-Dragon China Dragon,' blending youthful and sporty elements with more stable and sophisticated components. The front headlights feature C-shaped LED daytime running lights and a dual-lens design. The brake lights in the rear light cluster also use C-shaped LEDs, creating a stylish look that echoes the front headlights.
Was this review help?
19
2
Share
More Forum Discussions

Is it easy to repair oil leakage after the transmission is hit by a stone?

Whether the oil leakage after the transmission is hit by a stone is easy to repair depends on the extent of the collision. The following is an introduction to the situation of oil leakage after the transmission is hit by a stone: 1. Check for external oil leaks: Pay special attention to whether there is oil leakage at the front and rear crankshaft oil seals. Damage, aging, or wear at the contact surface between the crankshaft pulley and the oil seal can cause oil leakage at the front of the crankshaft. Damage to the rear crankshaft oil seal or a too-small oil return hole in the rear main bearing cap can cause oil leakage at the rear of the crankshaft. 2. Oil leakage at the front and rear oil seals: If oil seeps from multiple locations such as the front and rear cylinder head covers, front and rear valve lifter chambers, oil filter, and oil pan gasket, but no obvious leak is found, check the crankcase ventilation system. Clean the crankcase ventilation pipes and check if the PCV valve is malfunctioning due to carbon buildup and sticking. 3. Check the oil pressure: If oil continues to leak from the oil filter and some oil pipe joints after tightening, check whether the oil pressure is too high and whether the oil pressure relief valve is malfunctioning.
8
5
Share

What Causes the Delay in Rearview Camera?

Delay in the rearview camera indicates aging of the rearview camera system. Below is a detailed introduction to the features of the rearview camera: 1. 4-Channel Signal: The system has a wide voltage input of 11-32V and can connect up to 4 camera signals, widely used in various vehicles. It is suitable for unstable power supply voltage in cold conditions, has strong anti-interference capability, and built-in overheat and overcurrent protection. 2. Screen Splitting: Equipped with 4-screen splitting function, allowing selection between single screen and 4-screen display. 3. Forced Start Signal: 4 sets of forced start signals, named CAM1, CAM2, CAM3, and CAM4, with reverse priority. In any state, it automatically switches to the reverse camera when reversing and returns to the original state after reversing, achieving automatic wake-up function for reversing. The priority level is CAM1 > CAM2 > CAM3 > CAM4. 4. Screen Mirroring: Each of the 4 screens can be individually set to mirror or non-mirror mode.
1
0
Share

How to Deal with Water Accumulation Sound in Car Doors?

You can use the door drain valve to drain the water. The door drain valve will automatically remove the accumulated water inside the door. If the door drain valve is clogged, it will affect the drainage rate. Below are methods regarding a clogged door drain valve: Location of the door drain valve: Generally, it is located at the lowest edge of the door, with three small black squares, which are the car door drain valves. Reason for clogging: The door drain holes are usually located at the lower part of the door panel, with 1-2 holes. Most door panel drain holes do not have a hose for guidance, and rainwater flows directly through the rust-proofed door panel for drainage. Due to their low position, vehicles frequently driven on muddy roads are prone to having these drain holes blocked by mud. Hazards of clogging: Once the door drain holes are clogged, the accumulated water remaining inside the door panel can cause damage to the window regulator, audio system, and central door lock. Cleaning method: The door drain holes can be unclogged using hard objects like iron wires. Special care should be taken when cleaning the drain holes hidden inside the rubber seals to avoid damaging the seals.
13
3
Share

How to Check the Manufacturing Date of a Motorcycle Engine?

Inside the engine compartment, the specific manufacturing date of the vehicle is usually marked. Carefully check the vehicle's production date. The VIN (Vehicle Identification Number) is located below the front windshield of the car. The 10th digit of the VIN indicates the manufacturing date of the vehicle. Note that each vehicle's VIN is unique.
15
1
Share

What to Do After a Hit-and-Run Accident?

After the vehicle is hit, the owner can review the footage from the dashcam to promptly identify the license plate number of the vehicle involved in the collision. Check if there are any nearby surveillance cameras around the vehicle. Through the surveillance footage, the license plate number of the vehicle that caused the scratch and fled can also be identified. If the at-fault party refuses to compensate during the settlement process, the most sensible approach is to report the incident to the police. Only through certain enforcement measures will the at-fault party be compelled to provide compensation.
6
5
Share

Where is the Jetta windshield washer motor fuse located?

The fuse for the new Jetta's windshield washer motor is located in the engine fuse box of the car. This fuse box is situated on the left side of the engine compartment, adjacent to the car's battery and the left front headlight. How to determine if the washer motor is faulty: To check if the washer motor is damaged, observe whether the car's wipers are operational. If the wipers work but no water is sprayed, this phenomenon likely indicates a damaged washer motor or an issue with the electrical circuit. Common causes include a lack of windshield washer fluid, leaking hoses, clogged filters, blocked spray nozzles, a faulty washer motor, or circuit problems. It is necessary to open the engine hood for inspection. Precautions for the washer motor: Regularly check and replenish the windshield washer fluid. If the fluid runs out and the spray switch continues to be used, the pump will operate without fluid, causing the motor to overheat and burn out due to the lack of fluid flow. Therefore, the washer fluid must be frequently checked and replenished in a timely manner. If the nozzles fail to spray or the spray pattern is incorrect, check if the nozzle openings are clogged.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.