Is the Golf produced by Shanghai Volkswagen or FAW-Volkswagen?

What is the ON button?

"ON" is the power-on button, and "OFF" is the power-off button. ON and OFF are very common buttons. You can find them on the car light lever, where ON means turn on and OFF means turn off. Below is a related introduction to other functional buttons in cars: 1. The "SEL" button is the menu selection confirmation button, usually located on the multifunction steering wheel. 2. The "OK" button has the exact same function as the "SEL" button. Some cars use "SEL," while others use "OK." 3. The "A/C" button is the compressor switch, short for Air-Condition, which is the air conditioning cooling switch. This is because car air conditioning heating does not require the compressor. 4. "VOL+/-" are the volume adjustment buttons. VOL is the abbreviation of the word "volume," meaning sound level, and it can adjust the volume of the car audio. 5. "MUTE" is the mute button, which can mute the sound with one click. 6. "MODE" is the mode-switching button. 7. "SET" on the multifunction steering wheel is the cruise control function button.

17

5

Share

What is the age requirement for obtaining a B2 driver's license?

B2 driver's license can be obtained between the ages of 21 and 50. The vehicles allowed under a B2 license include heavy and medium-sized trucks or large, heavy, and medium-sized special operation vehicles, with heavy and medium-sized trucks mainly referring to trucks. Individuals aged 60 and above are not permitted to drive large buses, tractors, city buses, medium-sized buses, large trucks, trolleybuses, and trams. Age restrictions for other vehicle types: 1. Small cars (C1): 18 to 70 years old; 2. Automatic transmission cars (C2): 18 to 70 years old; 3. Medium-sized buses (B1): 21 to 50 years old; 4. Large buses (A1): 26 to 50 years old; 5. Motorcycles (E): 18 to 60 years old.

14

4

Share

Is Engine Carbon Cleaner Useful?

Engine carbon cleaner is useful, but due to its short cleaning time inside the engine and the inherent limitations of the no-disassembly cleaning method, its cleaning effect is relatively limited. Below is an introduction to cleaning engine carbon deposits: 1. Additive Cleaning (Fuel Additive): Additive cleaning involves directly adding the cleaner to the fuel tank to mix with the fuel. When the vehicle is started, the cleaner enters the combustion chamber along with the fuel, cleaning the carbon deposits inside the engine to a certain extent. 2. Drip Bottle Cleaning: Drip bottle cleaning is a no-disassembly method. This method involves introducing the cleaner into the engine's intake pipe via a drip bottle, where it is drawn into the combustion chamber along with the intake airflow. During this process, the cleaner removes carbon deposits from the engine's intake tract and combustion chamber. 3. Disassembly Cleaning: As the name suggests, disassembly cleaning involves removing the parts of the engine with carbon deposits for thorough cleaning.

12

5

Share

Rearview Mirror Distance Judgment Techniques for Reversing?

Here are the techniques for judging distance using rearview mirrors when reversing: 1. When the rear vehicle occupies half of the rearview mirror area, and only half of its body is visible, it indicates the rear vehicle is very close. Maintain your current lane and avoid turning. 2. When the rear vehicle occupies half of the side rearview mirror area and its entire body is visible, the distance is approximately 10 meters. Turning is only advisable after signaling and at slower speeds. 3. When the rear vehicle occupies one-third of the side rearview mirror area and its entire body is visible, the distance is about 15 meters, making it safe to turn. 4. When the rear vehicle occupies one-third of the right rearview mirror area, the distance is roughly 15 meters. If it occupies half of the right rearview mirror, the distance is about 10 meters. If the rear vehicle occupies half of the right rearview mirror, it is too close for a safe turn.

1

3

Share

What Causes the ABS Light to Illuminate in the Octavia?

ABS light illumination can occur in various states, each with different causes and solutions, as detailed below: State 1: ABS warning light remains constantly on (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting its ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed or wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the contaminants from the wheel speed sensor and adjust the gap between the sensor and the tone ring to restore normal function. Cause 2: Poor signal transmission due to loose system wiring connections or faulty ABS relay contacts. Solution: Inspect wiring connections and re-secure any loose connections. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple electrical components are in use, the battery voltage may drop below 10.5V. As engine speed increases and voltage rises, the ABS light turns off. This may also indicate insufficient power supply voltage to the ABS system due to poor terminal contact or grounding issues. Solution: Check battery specific gravity; inspect the charging system; examine power supply components (e.g., voltage relay or poor power contacts). State 3: ABS warning light stays on after engine start until engine IGFF turns it off. Cause: Poor grounding connection of ABS hydraulic valve body; faulty wiring connector of ABS hydraulic valve body; ABS control unit malfunction. Solution: Loosen and retighten the hydraulic valve body ground screw, cleaning contact surfaces if necessary; check for enlarged connector gaps; replace ABS or ABS/ASR control unit. State 4: ABS warning light illuminates during high-speed driving. Cause: The ABS control unit detects excessive speed difference between rear and front wheels; incorrect tire or wheel rim specifications. Solution: Refer to vehicle tire and wheel rim specifications listed on the fuel filler cap label. State 5: ABS warning light intermittently flashes. Cause: Improper brake light switch adjustment; internal brake light contact failure. Solution: With engine running, depress brake pedal, manually push brake switch linkage downward fully, then release pedal to complete self-positioning; replace brake light switch if necessary. When the ABS warning light is illuminated, it's advised to avoid continued driving as this indicates a fault in the anti-lock braking system. During emergency braking, wheel lock-up may cause loss of vehicle control and skidding, preventing the driver from decelerating or adjusting trajectory, posing significant safety risks.

20

4

Share

What car brand has three horizontal bars?

The three horizontal bars represent the Skywell brand. Skywell is an automotive technology brand under Skywell Automotive Technology Group Co., Ltd., specializing in the research, development, production, sales, and service of new energy vehicles. Its flagship model, the Skywell ME7, is positioned as a pure electric mid-size SUV with dimensions of 4685mm in length, 1970mm in width, and 1660mm in height, featuring a wheelbase of 2830mm and front-wheel drive configuration. The ME7 is equipped with a permanent magnet synchronous motor paired with a single-speed fixed gear ratio transmission, delivering a maximum power output of 160kW and peak torque of 330Nm.

14

3

Share

Is the Golf produced by Shanghai Volkswagen or FAW-Volkswagen?

What is the ON button?

What is the age requirement for obtaining a B2 driver's license?

Is Engine Carbon Cleaner Useful?

Rearview Mirror Distance Judgment Techniques for Reversing?

What Causes the ABS Light to Illuminate in the Octavia?

What car brand has three horizontal bars?

In which year was the Accord 8.5 generation released?

What is the Function of a Car Engine?

What is the difference between reissuance and renewal of a driver's license?

How Many Kilometers to Replace Spark Plugs?