Is the FAW-Volkswagen Jetta VS5 a joint venture car?

1 Answers
DelBrielle
07/30/25 12:41am
FAW-Volkswagen Jetta VS5 is a joint venture car. The Jetta VS5 is a compact SUV with exterior dimensions of 4419mm in length, 1841mm in width, and 1616mm in height, a wheelbase of 2630mm, a fuel tank capacity of 51 liters, a minimum trunk volume of 482 liters, and a curb weight of 1310kg. The Jetta VS5 is equipped with a 1.4L turbocharged engine, delivering a maximum horsepower of 150hp, a maximum power of 110kW, a maximum power speed of 5000 to 6000 rpm, a maximum torque of 250Nm, and a maximum torque speed of 1750 to 3000 rpm.
Was this review help?
11
1
Share
More Forum Discussions

What Causes Difficulty Starting a Honda Accord in Cold Weather?

The reason for difficulty starting a Honda Accord in cold weather is excessive carbon buildup inside the engine. Taking the 2021 Honda Accord as an example, it belongs to the mid-size sedan category with the following dimensions: length 4893mm, width 1862mm, height 1449mm, wheelbase 2830mm, fuel tank capacity 48.5 liters, and curb weight 1619kg. The 2021 Honda Accord features a MacPherson strut front suspension and a multi-link rear suspension. It is equipped with a 2.0L naturally aspirated engine producing maximum power of 146PS (107kW) and maximum torque of 175Nm, paired with an electronic continuously variable transmission.
16
0
Share

What is the setting method for Odyssey's automatic door locking while driving?

Odyssey's automatic door locking while driving can be set by following these steps: 1. Put the gear in P position; 2. Turn the key to the ON position with all four doors closed; 3. Press and hold the lock button for 6 seconds; 4. The hazard warning lights on the instrument panel will flash twice; 5. The automatic locking function is now activated. Automatic door locking while driving, also known as speed-sensitive auto lock, is an electronic device that automatically presses the door lock button when the vehicle reaches a preset speed, preventing accidental opening of the door. The purpose of the automatic locking function is anti-theft, allowing the doors to lock quickly after starting to drive, which can prevent door-pulling robberies during traffic jams or at red lights, providing a certain level of security.
9
0
Share

What is the reset method for the collision cutoff in the 2016 Lavida?

The reset method for the collision cutoff in the 2016 Lavida is: Use a decoder to access the 44 Power Steering System Engine Control Module, enter the security access code 20103 or 10608, and after successful login, proceed to the basic settings, then select 'Reset All Matching Values' to complete the process. The 2016 Lavida is a compact car with the following dimensions: length 4613mm, width 1765mm, height 1460mm, and a wheelbase of 2610mm. It features a MacPherson strut front suspension and a torsion beam rear suspension. The car is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 112PS, a maximum power of 82kW, and a maximum torque of 145Nm, paired with a 5-speed manual transmission.
3
5
Share

How to Turn Off the Wrench Light on a Car?

The method to turn off the wrench light on a car is to perform vehicle maintenance. The benefits of maintenance include: 1. Ensuring the vehicle remains in optimal performance condition; 2. Improving vehicle efficiency and reducing wear on parts and tires; 3. Enhancing driving safety; 4. Preventing potential hazards caused by vehicle issues; 5. Reducing noise and environmental pollution; 6. Maintaining a clean vehicle appearance and preventing damage. Maintenance tasks include: 1. Replacing engine oil, oil filter, and cleaning the air filter, checking for damage to the generator belt and wiper blades; 2. Checking if tire pressure is normal and inspecting tires for uneven wear, bulges, or damage; 3. Inspecting the vehicle's chassis, including brake pads, brake discs, connecting rods, ball joints, and CV joints for any scratches; 4. Checking all vehicle switches and lights to ensure they are functioning properly.
12
1
Share

Can I not replace the driving license if it is full of stamps?

If the driving license is full of stamps, it cannot be left unreplaced. You need to bring the owner's ID card, the motor vehicle driving license, and the motor vehicle registration certificate to the local vehicle management office or public security traffic management department for replacement. The motor vehicle driving license is subject to annual or biennial review, and the review time is determined based on the type and age of the vehicle. The purpose is to better control the use of the driving license and to promptly determine whether the holder still meets the conditions for the driving license. The process for replacing an expired driving license: 1. The replacement must be done within three months (90 days) before expiration by participating in the motor vehicle inspection; 2. For vehicles not exempt from inspection, the owner needs to bring a power of attorney, the driving license, and the compulsory traffic insurance policy to the local motor vehicle inspection station for inspection; 3. It is no longer necessary to apply for an inspection qualification mark. After passing the inspection, the endorsement will be directly noted on the supplementary page of the driving license.
18
5
Share

What is the solution for abnormal noise from car rubber bushings?

The solutions for abnormal noise from car rubber bushings are: 1. Disassemble the rubber bushing, wrap a layer of polytetrafluoroethylene plastic film on the stabilizer bar, apply grease, and reinstall the rubber bushing; 2. Replace the rubber bushing. The method for pressing in the small rubber bushing of the lower control arm is: 1. Apply lubricating paste on the lower control arm and the rubber bushing before pressing it in to facilitate installation; 2. Press the rubber bushing in at an angle. Once the outer edge of the rubber bushing is successfully inserted, use a hammer to assist in hammering it down, pressing it in at an inclined position. The replacement method for the control arm rubber bushing is: 1. Lift the car with a jack and remove the rubber bushing; 2. Remove both ends of the triangular arm, select a metal sleeve of the corresponding size, and install the rubber bushing; 3. Remove the screw, then use fire to burn out the middle metal sleeve after removal; 4. If the screw is not long enough, add a rubber bushing. Once it is almost in place, use an adjustable wrench with a shim to allow the rubber bushing to smoothly reach its position.
2
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.